-
Piroiz
Проблемы с двигателем или с материнкой на roland cx-24?
При включении выдает ошибку MOTOR VOLTAGE.
Это двигатель вентилятора глючнул или материнская плата полетела?
-
Salvares
Сообщение Salvares » 27 мар 2014 09:56
Такая же проблема((. Может кто нибудь ответ дать?
Piroiz
Может поделишься тем как решил этот вопрос?
-
Бушевский Роман
- Постоянный участник
- Сообщения: 237
- Зарегистрирован: 23 ноя 2013 17:36
- Последний визит: 08 июл 2020 10:03
- Изменить репутацию:
Репутация:
Голосов: 9 - Откуда: Украина
Сообщение Бушевский Роман » 31 мар 2014 10:30
Очень похоже что проблема в блоке питания, проверьте выходное напряжение на блоке питания, 5 вольт у тебя есть, проверь второй вольтаж
Такой как и все, но и своих тараканов хватает
-
Salvares
Сообщение Salvares » 01 апр 2014 08:52
Бушевский Роман
Спасибо на выходных займусь. как и что отпишусь.
Вернуться в «Режущие плоттеры ROLAND»
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и 0 гостей
ERROR DESCRIPTION
SCAN MOTOR ERROR
CODE : 0000 0000
Error detected as a result Error Detected at fi rst
NO
MEANING
0001
Feed Motor Deviation Error
(The order from the CPU does not match the
feedback of the Feed Motor.)
0004
Feed Motor Overcurrent Error 1
(Big load is put on the motor movement
instantaneously.)
0008
Feed Motor Overcurrent Error 2
(A little load is put on the motor movement for a
long time.)
000C
0004 and 0008 occurred at the same time.
0005
0001 and 0004 occurred at the same time.
0009
0001 and 0008 occurred at the same time.
0010
Scan Motor Deviation Error
(The order from the CPU does not match the
feedback of the Scan Motor.)
0040
Scan Motor Overcurrent Error 1
(Big load is put on the motor movement
instantaneously.)
0080
Scan Motor Overcurrent Error 2
(A little load is put on the motor movement for a
long time.)
00C0
0040 and 0080 occurred at the same time.
0050
0010 and 0040 occurred at the same time.
0090
0010 and 0080 occurred at the same time.
Revised 1
CAUSE
< External factors >
1. Media Jamming
2. Pull or move the carriage by hands.
3. Carriage runs into a thing or hands.
4. Media is stuck because it is caught by the paper pipe.
5. Media is pulled forcedly.
6. Too heavy media is loaded.
< Machine factors >
1. The grease lubrication of the motor gear is not enough.
2. Motor is broken or end of life.
3. Servo board is broken.
4. Tool carriage fi xation to the belt is loose.
5. The bearing inside the idle pulley is worn out.
6. The carriage belt loses steps.
7. Limit position is not appropriate.
8. Power supply for motor is broken.
5-6
(The symptom may be improved by greasing the belt.)
(When the limit position is not correctly set,
it may cause a scan motor error.)
(When the power supply voltage for the motor is not
supplied, the motor cannot move and it results in the
motor error. )
Symptom
I’m showing a motor error on the control panel display.
Cause
A motor error could be caused by a variety of reasons, refer to the possibilities below.
Solution
1. Weight of the material, too heavy of a roll. Please refer to the back of the users manual and check for the maximum weight for your model
2. Media brake is applied causing a feed motor error. Release the brake in the media supply area in back of the cutter. Repeat the job without using the brake.
3. Dirty grit roller. Remove the media and check the grit roller segments. Carefully rotate the grit roller manually to view the entire circumference of the roller. Use a soft bristle brush to remove any dirt. Never use a wire brush because it will damage the grit segments. The grit roller shaft is an integral part of the frame and has critical factory alignments, it can not be replaced.
4. Problem might be with the power to the motor, inner gear train or life of the motor. Contact your Roland Dealer or Authorized Service Center for assistance.