Коды неисправностей
469
041-210
041-211
Ошибка двухлоткового модуля или сдвоенного лотка большой емкости.
Выключите и снова включите аппарат. Если неисправность не устраняется,
обратитесь на горячую линию Xerox.
047-211
Аппаратная ошибка модуля вывода бумаги. Выключите и снова включите
аппарат. Если неисправность не устраняется, обратитесь на горячую
линию Xerox.
047-212
Ошибка модуля укладки со сдвигом. Выключите и снова включите аппарат.
Если неисправность не устраняется, обратитесь на горячую линию Xerox.
047-213
Ошибка финишера. Выключите и снова включите аппарат. Если
неисправность не устраняется, обратитесь на горячую линию Xerox.
047-214
Ошибка дуплексного модуля. Выключите и снова включите аппарат. Если
неисправность не устраняется, обратитесь на горячую линию Xerox.
047-215
Ошибка связи между основным блоком и модулем вывода. Выключите и
снова включите аппарат. Если неисправность не устраняется, обратитесь
на горячую линию Xerox.
047-216
Ошибка финишера. Выключите и снова включите аппарат. Если
неисправность не устраняется, обратитесь на горячую линию Xerox.
047-217
Ошибка связи между основным блоком и податчиком большой емкости.
Выключите и снова включите аппарат. Если неисправность не устраняется,
обратитесь на горячую линию Xerox.
047-218
Произошла ошибка связи между основным модулем и двухлотковым
модулем или сдвоенным лотком большой емкости. Выключите и снова
включите аппарат. Если неисправность не устраняется, обратитесь на
горячую линию Xerox.
062-210
Неисправен податчик оригиналов. Обратитесь на горячую линию Xerox.
062-211
Ошибка податчика оригиналов. Обратитесь на горячую линию Xerox.
062-277
Ошибка связи между сканером и податчиком. Обратитесь на горячую
линию Xerox.
062-394
Невозможно записать данные из-за недостатка места. Выключите и снова
включите аппарат.
062-790
Сканируемый документ защищен от копирования. Проверьте типы
документов, которые можно копировать, пользуясь руководством
пользователя, глава «Приступая к работе с аппаратом», раздел
«Нелегальное копирование».
071-210
071-211
Ошибка при использовании лотка 1. Выключите и снова включите аппарат.
Если неисправность не устраняется, обратитесь на горячую линию Xerox.
072-210
072-211
Ошибка при использовании лотка 2. Выключите и снова включите аппарат.
Если неисправность не устраняется, обратитесь на горячую линию Xerox.
073-210
073-211
Ошибка при использовании лотка 3. Выключите и снова включите аппарат.
Если неисправность не устраняется, обратитесь на горячую линию Xerox.
074-210
074-211
Ошибка при использовании лотка 4. Выключите и снова включите аппарат.
Если неисправность не устраняется, обратитесь на горячую линию Xerox.
077-211
Произошла ошибка связи с двухлотковым модулем или сдвоенным лотком
большой емкости. Выключите и снова включите аппарат. Если
неисправность не устраняется, обратитесь на горячую линию Xerox.
Код
Описание и меры по устранению
072-210 Tray 2 Lift Fail RAP
BSD-ON: BSD 7.8 Tray 2 Paper Stacking (STM)
BSD-ON: BSD 7.9 Tray 2 Paper Stacking (1TM)
BSD-ON: BSD 7.10 Tray 2 Paper Stacking (3TM)
BSD-ON: BSD 7.19 Tray 2 Paper Stacking (TTM)
072-210 Tray 2 lift NG has occurred three consecutive times.
Initial Actions
• Check for obstructions behind the tray.
• Ensure that the tray is loaded correctly.
• Ensure the tray is pushed fully home.
• Check the drive system between the bottom plate and the tray 2 feed/lift motor for operation failure.
Procedure
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
Refer to the procedures that follow as necessary:
• GP 6 How to Check a Motor.
• GP 7 How to Check a Sensor.
Perform the steps that follow:
1. Enter dC330, code 072-102. Check the tray 2 level sensor, PL 80.20 Item 6.
2. Enter dC330, code 072-002. Check the tray 2 feed/lift motor, PL 80.20 Item 4.
3. Check the drive gears, PL 80.20 for wear or damage. Install new components as necessary.
4. If the fault persists, install new components as necessary:
• 1TM PWB, PL 70.17 Item 5.
• 3TM PWB, PL 70.23 Item 5.
• STM PWB, PL 70.28 Item 4.
• TTM PWB, PL 70.90 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner’s property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON:7.8
After the Tray 2 Feed/Lift Motor turned On, the Tray 2 Level Sensor did not turn On within the
specified time.
Initial Actions
•
Reload paper in the tray correctly.
•
Remove foreign substances in the tray.
•
Power OFF/ON
Procedure
Remove the tray and reinstall. The Tray 2 Feed/Lift Motor can be heard.
Y
N
Execute
Component
Control[071-008 Tray 2 Feed/Lift Motor ON]. The Tray 2 Feed/Lift
Motor
(PL
2.3) can be heard.
Y
N
Check the connections of P/J202,
J409
are connected correctly.
Y
N
Connect P/J202,
P/J602
Remove the Tray 1 Feed/Lift Motor
Replace the Tray 2 Feed/Lift Motor with the Tray 1 Feed/Lift Motor.
Execute
Component
Control[071-008 Tray 2 Feed/Lift Motor ON]. The Tray 1 Feed/
Lift Motor
(PL
2.3) can be heard.
Y
N
Return the Tray 1 Feed/Lift Motor to its original position.
Check the wire between J202 and J409 for an open circuit or a short circuit
(BSD 7.8
Flag
1). The wire between J202 and J409 is conducting without
an open circuit or a short circuit.
Y
N
Repair the open circuit or short circuit.
Replace the MCU PWB
(PL
Return the Tray 1 Feed/Lift Motor to its original position.
Replace the Tray 2 Feed/Lift Motor
Go to the
OF 2
(SIZE SWITCH ASSY RAP).
Check the installation of the Tray 2 Level Sensor
The Tray 4 Level Sensor is installed correctly and the actuator works.
Y
N
Reinstall the Tray 4 Level Sensor.
Execute
Component
Control[071-207 Tray 2 Level Sensor]. Manually activate the Tray 2 Level
Sensor
(PL
2.3). The display changes.
Launch Version
WorkCentre 5225, 5230
P/J602
and P/J409. P/J202,
P/J602
and P/J409.
(PL
2.3) and the Tray 2 Feed/Lift Motor
9.1).
(PL
2.3).
(PL
2.3) and the operation of the actuator.
Y
N
Check the connections of P/J102,
are connected correctly.
Y
N
Connect P/J102,
Check the wire between J102 and J409 for an open circuit or a short circuit (BSD 7.8
2/Flag
3). The wire between J102 and J409 is conducting without an open circuit or
a short circuit.
Y
N
Repair the open circuit or short circuit.
Measure the voltage between the MCU PWB P409B-7 (+) and GND (-) (BSD 7.8
The voltage is approx. +5VDC.
Y
N
Replace the MCU PWB
Measure the voltage between the MCU PWB P409B-9 (+) and GND (-) (BSD 7.8
and
P/
Activate the actuator of the Tray 2 Level Sensor
Y
N
Replace the Tray 2 Level Sensor
Replace the MCU PWB
(PL
2.3).
Replace the MCU PWB
(PL
February, 2008
2-527
P/J602
and P/J409. P/J102,
P/J602
and P/J409.
(PL
9.1).
(PL
2.3). The voltage changes.
(PL
2.3).
(PL
9.1).
9.1).
P/J602
and
P/J409
Flag
Flag
3).
Flag
2).
Status Indicator Raps
072-210