Thanks: 0
Likes: 0
Dislikes: 0
-
05-22-2014
#1
Xerox 4112 Jam in face down mode 077-111
xerox 4112
problem with jam at duplex fault code 77-111
paper jamed in duplex when change from 1 side to 2 to 2 side and and inversely, when going more then 3 paper ( 1 work fine )
and when change output settings to paper face up works fine..but cant print face up in drivers no have that options…..
i try other duplex unit, other inverter, sensor below fuser, check connectors on back and rear.. reset connectors on boards…but still have problem….
-
05-22-2014
#2
Senior Tech
250+ Posts
- Rep Power
- 25
Re: Xerox 4112 Jam in face down mode 077-111
I recently experienced a similar issue on a D95 (same mechanical hardware as 4110). The Invert gate solenoid was bad. Clear plastic paper guide under 2d directs the paper into to inverter for duplex or face down printing. Alternately to the finisher for face up printing. If the solenoid is bad the gate (paper guide) won’t change the paper direction, causing it to go into the inverter instead of the finisher, when printing face up.
Test it by making a copy and change the output format. Face up then face down then back to face up. This will cause the solenoid to move the paper guide. If it only jams in one of the output formats the solenoid is bad.
REF. PL 13.12 Inverter — Gate. Items 3&7
Hope this was of some help.
Good luck,
-
05-22-2014
#3
Re: Xerox 4112 Jam in face down mode 077-111
Usually the inverter gate solenoid or the duplex gate solenoid. You also want to remove the duplex unit and drawer assembly to inspect the big black connectors that make contact when you slide these units into place. Ive often seen these connectors break / crack. check both sides of both connectors to ensure this is not the case.
Bookmarks
Bookmarks
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
- BB code is On
- Smilies are On
- [IMG] code is On
- [VIDEO] code is On
- HTML code is Off
Forum Rules
1 2 . P r o b le m S o l v in g
Other Errors
Category
Error Code
C P S M O
002-770
003-750
%
003-751
%
003-753
003-754
%
1 2 — 3 0
This section explains error codes.
If an error caused the printing to end abnormally or a malfunction
occurred in the printer, then an error message code (***-***) is
displayed.
If an error code not described in the following tables is displayed,
or the problem persists even after you have tried the following
solutions, contact the Customer Support Center.
Refer to the following table for error codes and information on how
to rectify the problem.
KEY POINT: If an error code is displayed, all print data of the
printer as well as print data stored in the built-in memory of
the machine is discarded.
Errors are divided into the following Categories:
•
C: Copy
•
P: Print
•
S: Scan
•
M: Mail
•
O: Others Problems
%
% Cause
Unable to process job template due to insufficient hard
disk space.
Remedy
Remove unnecessary data from the hard disk to
increase free disk space.
Cause
Unable to store any documents with 2 Sided Book Copy
feature.
Remedy
Check the 2 Sided Book Copy settings.
Refer to «2 Sided Book Copy (Making 2 Sided Copies of Facing
Pages)» on page 3-34.
%
Cause
The machine is unable to process size, because the
specified document area is too small.
Remedy
Increase resolution or scan area size.
%
Cause
The selected resolution was too large for scanning
mixed size originals using document feeder.
Remedy
Decrease Scan Resolution to 200dpi or less, and
rescan.
%
Cause
An error occurred in the document scanner.
Remedy
Reprocess the job.
Cause and Remedy
X e r o x 4 11 0 / 4 5 9 0 U s e r G u i d e
Укладчик большой емкости
20-12
Xerox
®
D95/D110/D125 Копир/принтер
Руководство пользователя
Коды ошибок
Код ошибки
Возможная причина
Рекомендуемое решение
049-100
049-101
049-102
Ошибка датчика
верхнего лотка
• Осторожно удалите все
обрывки бумаги из областей
удаления застрявшей бумаги.
• Выключите и включите
устройство.
• Если проблема сохраняется,
обратитесь в центр поддержки
заказчиков.
049 104
049 105
049 106
049 108
Ошибка датчика
обходного лотка
• Осторожно удалите все
обрывки бумаги из областей
удаления застрявшей бумаги.
• Выключите и включите
устройство.
• Если проблема сохраняется,
обратитесь в центр поддержки
заказчиков.
049 113
049 114
049 115
049 116
Ошибка датчика
укладчика
• Осторожно удалите все
обрывки бумаги из областей
удаления застрявшей бумаги.
• Выключите и включите
устройство.
• Если проблема сохраняется,
обратитесь в центр поддержки
заказчиков.
049 117
049 119
Ошибка датчика пути
обходного лотка
• Осторожно удалите все
обрывки бумаги из областей
удаления застрявшей бумаги.
• Выключите и включите
устройство.
• Если проблема сохраняется,
обратитесь в центр поддержки
заказчиков.
049 121
Ошибка датчика
выхода укладчика
• Осторожно удалите все
обрывки бумаги из областей
удаления застрявшей бумаги.
• Выключите и включите
устройство.
• Если проблема сохраняется,
обратитесь в центр поддержки
заказчиков.