DOOSAN Fault Codes DTC
Doosan Fault Codes DTC
Doosan Fault Codes DTC.pdf
Adobe Acrobat Document
181.9 KB
DOOSAN Excavator Fault Codes List DTC
FAULT CODE — NAME — FAULT DESCRIPTION
12 NONE Signifies the end of one pass through the fault list
14 ECTSensorInputLow Normally set if the coolant sensor wire is shorted to ground
15 ECTSensorInputHigh Set if the coolant sensor wire is disconnected or open
16 ECTRangeHigh Coolant sensor has measured an excessive temperature or shorted to GND
22 ThrottleSensorInputLo TPS1 signal wire is open
23 ThrottleSensorInputHi TPS1 signal wire is shorted
24 ThrottleSensorRangeLo TPS Sensor malfunction
25 ThrottleSensorRangeHi TPS Sensor malfunction
26 ETCSticking ETC driver signal wire is open or the throttle plate is sticking inside the throttle body
27 PredictedTPSDifference TPS1 is different than calculated position
28 ETCSpringTestFailed Throttle return spring failed keyup test
29 ETCDriverFault Throttle driver over-current or driver signals shorted
33 MapSensorInputLow MAP signal disconnected or open circuit
34 MapSensorInputHigh MAP signal shorted or sensor failure
37 IATSensorInputLow TMAP sensor failure or shorted circuit
38 IATSensorInputHigh TMAP disconnected or IAT signal open
42 EST1Low Coil driver signal low or under current
43 EST1High Coil driver signal high or over current
52 LowOilPressure Low engine oil pressure
53 BatterySensorInputLow Battery voltage measured below 8.0 VDC
54 BatterySensorInputHigh Battery voltage measured above 15.9 VDC
55 XDRPSensorInputLow Measured sensor transducer power is below 4.6 VDC
56 XDRPSensorInputHigh Measured sensor transducer power is above 5.2 VDC
57 Engine OverSpeed RPM increased above maximum rpm setpoint
61 Pedal1SensorInputLo APP1 signal disconnected, open circuit or sensor malfunction
62 Pedal1SensorInputHi APP1 sensor failure or shorted circuit
63 Pedal1SensorRangeLo APP1 potentiometer malfunction
64 Pedal1SensorRangeHi APP1 potentiometer malfunction
65 Pedal2SensorInputLo APP2 sensor failure or shorted signal
66 Pedal2SensorInputHi APP2 signal disconnected, open circuit or sensor malfunction
67 Pedal2SensorRangeLo APP2 potentiometer malfunction
68 Pedal2SensorRangeHi APP2 potentiometer malfunction
69 Pedal1ToPedal2Difference Measured APP2 pedal position signal is different than APP1
signal
71 AFRTrimValveOutput FTV modulation driver signal fault
72 AFRTrimValveLowerDC FTV duty cycle at lower (LEAN) limit
73 AFRTrimValveUpperDC FTV duty cycle at upper (RICH) limit
74 O2SensorSwitching O2 sensor not switching across the reference AFR voltage
77 OxygenSensorInputHigh O2 sensor signal shorted to +5 VDC
Doosan DX225LCA Excavator Fault Codes List – FMI & V-Codes See also: Doosan Service Repair Manuals PDF
Failure Information Code at Machine Side
| Code | Failure Component | Measuring Points | Correct Value | Remarks | |
| Active | Passive | ||||
| V201 | Gauge Panel
Communication Error |
CN7-4
CN7-5 |
– |
R = 60 ±5 Ω | It is a composite resistance of CAN line. This value has to be measured by connected condition of CAN line. |
|
V202 |
Ecu Communication Error |
CN4-4 CN4-5 |
– |
R = 60 ±5 Ω |
|
|
V210 |
Pump P/V |
CN1-10 CN1-21 |
– |
R = 18 ±2 Ω (25°C (77°F)) |
Pump proportional pressure reducing valve. |
| V211 | Cooling Fan P/V | – | – | N.A. | |
|
V212 |
Flow Control P/V |
CN1-19 CN1-20 |
– |
R = 14 ±2 Ω (25°C (77°F)) |
Flow control proportional pressure reducing valve. |
|
V213 |
Relief Pressure Up S/V |
CN1-1 CN1-11 |
V = V_volt (Note 4.) |
R = 26.2 ±2 Ω (25°C (77°F)) |
Breaker/boost/ shear selector switch has to be selected as a boost function and the boost switch on the right-hand joystick is “ON” status. |
|
V214 |
High Speed S/V |
CN1-1 CN1-12 |
V = V_volt |
R = 26.2 ±2 Ω (25°C (77°F)) |
Voltage is only measured when the pressure switch (Py) is turned “ON.” |
|
V215 |
Swing Priority S/V |
CN1-1 CN1-13 |
V = V_volt |
R = 26.2 ±2 Ω (25°C (77°F)) |
Work mode has to be selected as a trenching mode. |
| V216 | Reverse Fan Speed S/V | – | – | N.A. | |
|
V217 |
Starter Relay |
CN1-1 CN1-15 |
V = V_volt |
– |
It has to be measured in engine start up state. |
| V218 |
After Heat Relay |
1-16
1-04 |
– |
– |
N.A. |
| Code | Failure Component | Measuring Points | Correct Value | Remarks | |
| Active | Passive | ||||
| V220 |
Front Pump Press. Sensor |
CN3-1
CN3-2 |
V = IV |
– |
It has to be measured in engine stop state. |
| V221 |
Rear Pump Press. Sensor |
CN3-3
CN3-4 |
V = IV |
– |
|
|
V222 |
Hyd. Oil Temperature Sensor |
CN3-9 CN3-10 |
– |
R = 2.45 ±0.25 k Ω (25°C (77°F))
R = 320 ±32 Ω (80°C (176°F)) |
|
| V223 | Water Temperature Sensor | – | – | N.A. | |
| V224 | Engine Speed Sensor | – | – | N.A. | |
|
V225 |
Fuel Level Sensor |
CN3-7 CN3-8 |
– |
Empty: 5 ±0.25 k Ω
Full: 320 ±32 Ω |
|
|
V226 |
Alternator Potential |
CN2-14 CN1-8 |
V = 2 ±1V |
– |
It has to be measured in engine stop state. |
|
V227 |
Dial |
CN3-16 CN3-7 |
– |
R = 1.0 ±0.3 k Ω
R = 4.0 ±1.5 k Ω |
|
| V228 | Tps (Wheel) | – | – | N.A. | |
| V229 | Parking Brake Press. Sensor | – | – | N.A. | |
| V230 | E/g Control Motor Sensor | – | – | N.A. |
Active value: Starter switch has to be turned “ON”NOTE:
- Measuring points between component and wire harness have to be connected. Passive value: Starter switch has to be turned “OFF”
- Measuring points between component and wire harness have to be disconnected.
- Measuring points are engine controller’s points and passive value is each component’s value.
- V_batt: Source power of equipment.
FMIs (Failure Mode Identifier)
| FMI 0 | Above normal range (DATA VALID but ABOVE NORMAL OPERATIONAL RANGE) |
| FMI 1 | Below normal range (DATA VALID but BELOW NORMAL OPERATIONAL RANGE) |
| FMI 2 | Incorrect signal (DATA ERRATIC, INTERMITTENT OR INCORRECT) |
| FMI 3 | Voltage above normal (VOLTAGE ABOVE NORMAL OR SHORTED TO HIGH SOURCE) |
| FMI 4 | Voltage below normal (VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE) |
| FMI 5 | Current below normal (CURRENT BELOW NORMAL OR OPEN CIRCUIT) |
| FMI 6 | Current above normal (CURRENT ABOVE NORMAL OR GROUNDED CIRCUIT) |
| FMI 8 | Abnormal signal (ABNORMAL FREQUENCY OR PULSE WIDTH OR PERIOD) |
| FMI 11 | Failure mode not identifiable (ROOT CAUSE NOT KNOWN – Malfunction) |
| FMI 31 | NOT AVAILABLE OR CONDITION EXISTS |
Когда FFXIV внезапно выдает ошибку с кодом 2002, 3001, 4004, 5003 или 5006, то поиграть уже не получается, и это не может не расстраивать.
Понятно, что «не пущает». Понятно, что на сервере опять что-то не так или он вообще в отключке. Но не всегда понятно (и не всем) понятно, когда это прекратиться и что в таком случае делать…
В этой связи, очень кратко о том,..
когда в Final Fantasy 14 выскакивает ошибка 2002, 3001, 4004, 5003 или 5006
Значит, отметим для начала, что хоть коды у этих ошибок и разные (следовательно, и причины возникновения у каждой тоже свои, как вы уже наверняка догадались), но как бы устраняются все они одним простым способом.
А именно, надо просто подождать, пока на стороне сервера игры ситуация не нормализуется, и он снова начнет функционировать должным образом.
Не пропустите: ОШИБКА 24202 В FFXIV И НЕ ПРОХОДИТ ОПЛАТА — ЧТО ДЕЛАТЬ
Тем более, что в качестве компенсации за все причиненные этими и прочими техническими сбоями неудобства компания Square Enix всем владельцам подписки начислила целую неделю бесплатной игры.
Плюс к этому, в обращении к игрокам Yoshi-P исчерпывающе объяснил причины перечисленных ошибок. Так что, нам остается только его процитировать:
-
почему возникает ошибка 2002 в FF14
Error 2002 случается, когда в центр обработки данных единовременно пытаются зайти более 17000 человек. Кроме того, эта же ошибка может возникать, когда у игрока нестабильное соединение или происходит потеря пакетов. Поэтому, чтобы проблему устранить, надо либо просто подождать, когда перегруз на сервере пройдет, либо проверить состояние интернет-соединения и наладить стабильное подключение, чтобы не приходилось постоянно отключаться и повторно подключаться.
-
почему возникают ошибки Error 3001, 4004, 5003 и 5006 в FF14
Игроки получат ошибку подключения с кодом 3001, 4004, 5003 или 5006 в FFXIV, когда подключение к серверу управления входом в систему истекает по причине слишком долгого пребывания в очереди. Разработчики планировали, что заданного периода ожидания в лобби будет достаточно, но очереди сейчас намного длиннее, чем предполагалось. Вскоре должно быть реализовано исправление, которое устранит эти ошибки.
Итого: когда видим код 2002, 3001, 4004, 5003 или 5006 в FF14, то не суетимся особо, а просто пробуем зайти в игру через некоторое время. Ну и на всякий проверяем состояние подключения со своей стороны.