Меню

Tennant t5 коды ошибок

ON- -BOARD BATTERY CHARGER ERROR CODES

DISPLAY CODE

bat

E01

E02

E03

SCt

Srt

T5 9002333 REV.02 (07-06)

T5 –Maintenance

(Page 3 of 15)

FAULT

Loose or damaged battery cable

Battery exceeded maximum voltage level.

Exceeded maximum battery voltage allowed.

Safety thermostat exceeded maximum internal

temperature.

Exceeded maximum time for charging phase

leaving the batteries undercharged due to a

sulfated or faulty battery.

Safety timer exceeded maximum charging

time. Interrupts charging cycle.

Possible internal short circuit.

SOLUTION

Check battery cable connections.

No action necessary.

No action necessary.

Check if the charger vents are obstructed.

Repeat the charging cycle and if the error

code E03 reappears check battery or

replace it.

Replace battery.

Contact Service Center.

M

9

Источник

  • Contents

  • Table of Contents

  • Troubleshooting

  • Bookmarks

Quick Links

T5

Scrubber-Dryer

English

EN

Operator Manual

R

For the latest Parts manual and other

language Operator manuals, visit:

9002347

www.tennantco.com/manuals

Rev. 07 (06-2016)

*000000*

www.tennantco.com

loading

Related Manuals for Tennant T5

Summary of Contents for Tennant T5

  • Page 1
    Scrubber-Dryer English Operator Manual For the latest Parts manual and other language Operator manuals, visit: 9002347 www.tennantco.com/manuals Rev. 07 (06-2016) *000000* www.tennantco.com…
  • Page 2
    It provides necessary operation and maintenance INTENDED USE instructions. Read this manual completely and The T5 walk behind scrubber is designed to scrub hard understand the machine before surfaces (concrete, asphalt, stone, synthetic, etc) in an operating or servicing it.

  • Page 3: Table Of Contents

    USING AN OFF- BOARD BATTERY CHARGER (OPTION) ……Tennant T5 (06- 16)

  • Page 4: Important Safety Instructions

    Keep battery compartment open when With pads or accessories not supplied or charging. approved by Tennant. The use of other pads may impair safety. WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials In outdoors areas.

  • Page 5
    All repairs must be performed by trained personnel. Do not modify the machine from its original design. Use Tennant supplied or approved replacement parts. Wear personal protective equipment as needed and where recommended in this manual. For Safety: wear protective gloves.

  • Page 6: Safety Labels

    Keep sparks and open flame away when charging. Keep battery compartment open when charging. FOR SAFETY LABEL — Read manual before Located at bottom side of operating machine. recovery tank. Located on recovery tank cover. Tennant T5 (12- 13)

  • Page 7: Machine Components

    11. Squeegee Assembly 25. Pad Driver Window 12. Solution Tank Clean-Out Port 26. Scrub Head Skirt 13. Recovery Tank Support Stand 27. Parking Brake 14. Control Board 28. Cylindrical Brush Scrub Head 15. Bucket Fill Port/Clean- out Port Tennant T5 (09- 08)

  • Page 8: Control Panel Components

    6. Solution flow decrease button (- ) 13. ec- H2O system indicator light (ec- H2O model) 7. Fault indicator — Contact Service 14. Main power on/off key switch 8. Supervisor Control indicator — Lockout feature 15. Hour meter Tennant T5 (09- 08)

  • Page 9: Machine Installation

    2. Lift the recovery tank and remove the right side battery compartment panel (Figure 1). 13mm on- board battery charger, make sure that the wrench required. charger is properly set for your battery type before charging (See ON- BOARD CHARGER SETTINGS). Tennant T5 (12- 13)

  • Page 10: How The Machine Works

    Stripping Pad (Brown) — Used for stripping of floor finish to prepare the floor for recoating. Heavy Duty Stripping Pad (Black) — Used for aggressive stripping of heavy finishes/sealers, or very heavy duty scrubbing. Tennant T5 (06- 15)

  • Page 11: Machine Setup

    2. Attach the pad to the pad driver before installing FIG. 5 the driver. Secure pad with centerlock (Figure 9). 4. Connect the vacuum hose to the squeegee assembly. Loop the hose as shown using the hose clip provided (Figure 6). FIG. 9 FIG. 6 Tennant T5 (12- 13)

  • Page 12
    (Figure 12). 4. Check the brushes to ensure they are properly adjusted (See ADJUSTING SCRUB HEAD BRUSHES). FIG. 12 6. Check the scrub head to ensure that it is properly adjusted (See ADJUSTING SCRUB HEAD BRUSHES). Tennant T5 (06- 16)

  • Page 13: Ec-H2O Nanoclean Water Conditioning Cartridge (Ec-H2O Nanoclean Model)

    (Figure 16). 3. When the supply hose is not in use, connect the storage plug to prevent the FaST system from drying out and clogging up the hose. (Figure 19). FIG. 16 FIG. 19 Tennant T5 (06- 15)

  • Page 14: Filling Solution Tank

    ATTENTION: ec-H2O NanoClean Models- During first time use and after replacing the water conditioning cartridge, the ec-H2O system will automatically override the selected solution flow rate for up to 75 minutes. Tennant T5 (06- 15)

  • Page 15
    FaST scrubbing or for ec-H2O (Figure 25). To reverse the machine, simply push scrubbing on ec-H2O models manufactured before the control handle bail forward. Raise squeegee ec-H2O NanoClean models. when reversing machine. Tennant T5 (06- 15)

  • Page 16: Emergency Shut- Off Button

    3. Do not operate machine in areas where the ambient temperature is above 43 C (110 F). Do not operate scrubbing functions in areas where the ambient temperature is below freezing 0 C (32 F) Tennant T5 (12- 13)

  • Page 17: Battery Charge Level Indicator

    FIG. 31 FIG. 32 ec- H2O SYSTEM INDICATOR LIGHT CODE CONDITION Solid green Normal operation Blinking red Flush ec- H2O module Solid red Contact Service Center Tennant T5 (06- 15)

  • Page 18: Hour Meter

    2. Connect the solution hose to the coupler at the lower right side of machine (Figure 34). FIG. 37 FIG. 34 Tennant T5 (09- 08)

  • Page 19: Draining And Cleaning Tanks

    FIG. 41 4. Clean the float shut-off screen and debris tray located in the recovery tank (Figure 42). FIG. 42 Tennant T5 (12- 13)

  • Page 20: Draining Solution Tank

    FIG. 44 — FOR WET (Lead acid) BATTERIES 3. Clean the solution tank filter (Figure 45). OUTPUT VOLTAGE — 24 VOLTS OUTPUT CURRENT — 20 AMPS AUTOMATIC SHUTOFF CIRCUIT FOR DEEP CYCLE BATTERY CHARGING FIG. 45 Tennant T5 (06- 16)

  • Page 21: On- Board Battery Charger Settings

    Lead Acid (Wet) The charger cord must be unplugged when resetting. Gel (Generic) Charger Version 3.5 Exide GEL BATTERY LEAD ACID BATTERY Generic GEL BATTERY Charger Version 3.4 or earlier GEL BATTERY LEAD ACID BATTERY FIG. 47 Tennant T5 (12- 13)

  • Page 22: Using The On- Board Battery Charger

    4. Prop up the recovery tank for ventilation (Figure 48). FIG. 48 5. Connect the charger’s AC power supply cord into a properly grounded receptacle (Figure 49). NOTE: The machine will not operate when charging. FIG. 49 Tennant T5 (NIL)

  • Page 23: On- Board Battery Charger Error Codes

    E03 reappears check battery or re- sulfated or faulty battery. place it. Safety timer exceeded maximum charging Replace battery. time. Interrupts charging cycle. Possible internal short circuit. Contact Service Center. Tennant T5 (03- 08)

  • Page 24: Using An Off- Board Battery Charger (Option)

    FOR SAFETY: Do not disconnect the charger’s DC cord from the machine’s receptacle when the charger is operating. Arcing may result. If the charger must be interrupted during charging, disconnect the AC power supply cord first. Tennant T5 (12- 13)

  • Page 25: Cylindrical Brush Model

    6. Raise the scrub head and pull the machine away. 7. Observe the brush pattern on floor. If the brush pattern is uneven or tapered, adjustment is required. 8. Reconnect drive motor wire. Tennant T5 (06- 06)

  • Page 26
    4. To lower the brush end, turn the shaft clockwise for the front brush and counter- clockwise for the rear brush. Retighten hex screw (Figure 61). FIG. 61 5. Recheck brush pattern. NOTE: Replace brushes when worn to 15mm. Tennant T5 (06- 06)

  • Page 27: Maintenance Chart

    Check and clean 750 Hours Vacuum fan motor Replace carbon brushes Disk brush motors Replace carbon brushes Propelling motor Replace carbon brushes 1000 Hours Cylindrical brush motors Replace carbon brushes FaST water and air filters Replace Tennant T5 (12- 13)

  • Page 28: Machine Maintenance

    Rinse and clean out the recovery tank (Figure 63). FIG. 67 FIG. 63 7. Rotate pad or replace when worn (Figure 68). 3. Remove the recovery tank float shut- off screen and clean (Figure 64). Disk Model FIG. 68 FIG. 64 Tennant T5 (12- 13)

  • Page 29
    71). Replace when worn to a length of 15mm. 13. Check the condition of the squeegee blade wiping edge (Figure 74). Rotate blade if worn (See SQUEEGEE BLADES). 15mm Cylindrical Brush Model FIG. 71 FIG. 74 Tennant T5 (06- 16)

  • Page 30: Monthly Maintenance

    Cylindrical Brush Model FIG. 79 2. Inspect and clean the recovery tank cover seal (Figure 80). Replace if damaged. FIG. 77 17. Recharge the batteries (Figure 78). See CHARGING BATTERIES. FIG. 80 Tennant T5 (06- 16)

  • Page 31: Battery Maintenance

    Add distilled water if low. DO NOT OVERFILL. The electrolyte will expand and may overflow when charging. After charging, distilled water can be added up to about 3 mm (0.12 in) below the sight tubes. FIG. 83 Tennant T5 (06- 16)

  • Page 32: Squeegee Blades

    (Figure 85). FIG. 87 MOTOR MAINTENANCE Replace motor carbon brushes as indicated. Contact trained personnel for carbon brush replacement. Carbon Brush Replacement Hours Drive Transaxle Motor Vacuum Motor Disk Brush Motors Cylindrical Brush Motors 1000 FIG. 85 Tennant T5 (12- 13)

  • Page 33: Fast System Maintenance

    (Figure 92). 3. Replace the water and air filter. An 8mm hex wrench is required to install the new water filter (Figure 90). Water Filter (50 Mesh/Brown) Gray Collar FIG. 92 Air Filter (50 Mesh/Brown) FIG. 90 Tennant T5 (06- 15)

  • Page 34: Ec- H2O Module Flush Procedure

    7 minute cycle in order to reset the system indicator light and alarm. FIG. 94 Repeat flush procedure if the ec- H2O module does not reset. If module fails to reset, contact an Authorized Service Center. Tennant T5 (06- 15)

  • Page 35: Jacking Up Machine

    5. Open the recovery tank cover to promote air circulation. ATTENTION: Do not expose machine to rain, store indoors. 6. If storing machine in freezing temperatures, follow the FREEZE PROTECTION instructions below. Tennant T5 (06- 16)

  • Page 36: Freeze Protection

    If the antifreeze is not properly flushed from the ec- H2O system, the ec- H2O module may detect an error and not function (ec- H2O switch indicator light will turn red). If this occurs, reset key and repeat the flush procedure as described below. Tennant T5 (06- 15)

  • Page 37: Troubleshooting

    Faulty control board Contact Service Center Wheels raised off floor Contact Service Center Faulty transaxle motor or wiring Contact Service Center Worn carbon brushes Contact Service Center Exceeded maximum incline Avoid steep inclines and reset key Tennant T5 (06- 06)

  • Page 38
    Replace battery Batteries need maintenance See BATTERY MAINTENANCE Faulty battery charger Repair or replace battery charger Solution flow and brush pressure Supervisor controls are activated Contact your Supervisor buttons and FaST system switch (lockout feature) are locked Tennant T5 (06- 06)
  • Page 39
    Defective module Contact Service Center solid red ec- H2O system indicator light Defective light or module Contact Service Center does not turn on No water flow Clogged module Contact Service Center Defective solution pump Replace solution pump Tennant T5 (06- 15)

  • Page 40: Control Panel Fault Indicator Codes

    Restart key to reset. All battery lights blink Emergency- Stop button activated Turn button clockwise to reset. All battery lights ripple Key turned on while bail was engaged. Release the control handle start bail. Tennant T5 (06- 06)

  • Page 41: General Machine Dimensions/Capacities/Performance

    SOUND POWER LEVEL 84 dBa 83 dBa +UNCERTAINTY K VIBRATION AT HAND- ARM* <2.5 m/s <2.5 m/s GRADE LEVEL, MAX. Scrubbing 5%, Transporting 8%, Ramp Loading (tanks empty) 19.5% * Values per EN 60335- 2- 72 Tennant T5 (12- 13)

  • Page 42: Machine Dimensions

    800 mm Disk Disk Disk Cylindrical Cylindrical 1.346 mm 1.400 mm 1.463 mm 1.387 mm 1.387 mm 645 mm 737 mm 838 mm 711 mm 864 mm 908 mm 1.051 mm 1.185 mm 1.051 mm 1.185 mm Tennant T5 (09- 08)

Источник

  • Contents

  • Table of Contents

  • Troubleshooting

  • Bookmarks

Quick Links

T5

Scrubber-Dryer

English

EN

Operator Manual

R

For the latest Parts manual and other

language Operator manuals, visit:

9002347

www.tennantco.com/manuals

Rev. 07 (06-2016)

*000000*

www.tennantco.com

loading

Related Manuals for Tennant T5

Summary of Contents for Tennant T5

  • Page 1
    Scrubber-Dryer English Operator Manual For the latest Parts manual and other language Operator manuals, visit: 9002347 www.tennantco.com/manuals Rev. 07 (06-2016) *000000* www.tennantco.com…
  • Page 2
    It provides necessary operation and maintenance INTENDED USE instructions. Read this manual completely and The T5 walk behind scrubber is designed to scrub hard understand the machine before surfaces (concrete, asphalt, stone, synthetic, etc) in an operating or servicing it.

  • Page 3: Table Of Contents

    USING AN OFF- BOARD BATTERY CHARGER (OPTION) ……Tennant T5 (06- 16)

  • Page 4: Important Safety Instructions

    Keep battery compartment open when With pads or accessories not supplied or charging. approved by Tennant. The use of other pads may impair safety. WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials In outdoors areas.

  • Page 5
    All repairs must be performed by trained personnel. Do not modify the machine from its original design. Use Tennant supplied or approved replacement parts. Wear personal protective equipment as needed and where recommended in this manual. For Safety: wear protective gloves.

  • Page 6: Safety Labels

    Keep sparks and open flame away when charging. Keep battery compartment open when charging. FOR SAFETY LABEL — Read manual before Located at bottom side of operating machine. recovery tank. Located on recovery tank cover. Tennant T5 (12- 13)

  • Page 7: Machine Components

    11. Squeegee Assembly 25. Pad Driver Window 12. Solution Tank Clean-Out Port 26. Scrub Head Skirt 13. Recovery Tank Support Stand 27. Parking Brake 14. Control Board 28. Cylindrical Brush Scrub Head 15. Bucket Fill Port/Clean- out Port Tennant T5 (09- 08)

  • Page 8: Control Panel Components

    6. Solution flow decrease button (- ) 13. ec- H2O system indicator light (ec- H2O model) 7. Fault indicator — Contact Service 14. Main power on/off key switch 8. Supervisor Control indicator — Lockout feature 15. Hour meter Tennant T5 (09- 08)

  • Page 9: Machine Installation

    2. Lift the recovery tank and remove the right side battery compartment panel (Figure 1). 13mm on- board battery charger, make sure that the wrench required. charger is properly set for your battery type before charging (See ON- BOARD CHARGER SETTINGS). Tennant T5 (12- 13)

  • Page 10: How The Machine Works

    Stripping Pad (Brown) — Used for stripping of floor finish to prepare the floor for recoating. Heavy Duty Stripping Pad (Black) — Used for aggressive stripping of heavy finishes/sealers, or very heavy duty scrubbing. Tennant T5 (06- 15)

  • Page 11: Machine Setup

    2. Attach the pad to the pad driver before installing FIG. 5 the driver. Secure pad with centerlock (Figure 9). 4. Connect the vacuum hose to the squeegee assembly. Loop the hose as shown using the hose clip provided (Figure 6). FIG. 9 FIG. 6 Tennant T5 (12- 13)

  • Page 12
    (Figure 12). 4. Check the brushes to ensure they are properly adjusted (See ADJUSTING SCRUB HEAD BRUSHES). FIG. 12 6. Check the scrub head to ensure that it is properly adjusted (See ADJUSTING SCRUB HEAD BRUSHES). Tennant T5 (06- 16)

  • Page 13: Ec-H2O Nanoclean Water Conditioning Cartridge (Ec-H2O Nanoclean Model)

    (Figure 16). 3. When the supply hose is not in use, connect the storage plug to prevent the FaST system from drying out and clogging up the hose. (Figure 19). FIG. 16 FIG. 19 Tennant T5 (06- 15)

  • Page 14: Filling Solution Tank

    ATTENTION: ec-H2O NanoClean Models- During first time use and after replacing the water conditioning cartridge, the ec-H2O system will automatically override the selected solution flow rate for up to 75 minutes. Tennant T5 (06- 15)

  • Page 15
    FaST scrubbing or for ec-H2O (Figure 25). To reverse the machine, simply push scrubbing on ec-H2O models manufactured before the control handle bail forward. Raise squeegee ec-H2O NanoClean models. when reversing machine. Tennant T5 (06- 15)

  • Page 16: Emergency Shut- Off Button

    3. Do not operate machine in areas where the ambient temperature is above 43 C (110 F). Do not operate scrubbing functions in areas where the ambient temperature is below freezing 0 C (32 F) Tennant T5 (12- 13)

  • Page 17: Battery Charge Level Indicator

    FIG. 31 FIG. 32 ec- H2O SYSTEM INDICATOR LIGHT CODE CONDITION Solid green Normal operation Blinking red Flush ec- H2O module Solid red Contact Service Center Tennant T5 (06- 15)

  • Page 18: Hour Meter

    2. Connect the solution hose to the coupler at the lower right side of machine (Figure 34). FIG. 37 FIG. 34 Tennant T5 (09- 08)

  • Page 19: Draining And Cleaning Tanks

    FIG. 41 4. Clean the float shut-off screen and debris tray located in the recovery tank (Figure 42). FIG. 42 Tennant T5 (12- 13)

  • Page 20: Draining Solution Tank

    FIG. 44 — FOR WET (Lead acid) BATTERIES 3. Clean the solution tank filter (Figure 45). OUTPUT VOLTAGE — 24 VOLTS OUTPUT CURRENT — 20 AMPS AUTOMATIC SHUTOFF CIRCUIT FOR DEEP CYCLE BATTERY CHARGING FIG. 45 Tennant T5 (06- 16)

  • Page 21: On- Board Battery Charger Settings

    Lead Acid (Wet) The charger cord must be unplugged when resetting. Gel (Generic) Charger Version 3.5 Exide GEL BATTERY LEAD ACID BATTERY Generic GEL BATTERY Charger Version 3.4 or earlier GEL BATTERY LEAD ACID BATTERY FIG. 47 Tennant T5 (12- 13)

  • Page 22: Using The On- Board Battery Charger

    4. Prop up the recovery tank for ventilation (Figure 48). FIG. 48 5. Connect the charger’s AC power supply cord into a properly grounded receptacle (Figure 49). NOTE: The machine will not operate when charging. FIG. 49 Tennant T5 (NIL)

  • Page 23: On- Board Battery Charger Error Codes

    E03 reappears check battery or re- sulfated or faulty battery. place it. Safety timer exceeded maximum charging Replace battery. time. Interrupts charging cycle. Possible internal short circuit. Contact Service Center. Tennant T5 (03- 08)

  • Page 24: Using An Off- Board Battery Charger (Option)

    FOR SAFETY: Do not disconnect the charger’s DC cord from the machine’s receptacle when the charger is operating. Arcing may result. If the charger must be interrupted during charging, disconnect the AC power supply cord first. Tennant T5 (12- 13)

  • Page 25: Cylindrical Brush Model

    6. Raise the scrub head and pull the machine away. 7. Observe the brush pattern on floor. If the brush pattern is uneven or tapered, adjustment is required. 8. Reconnect drive motor wire. Tennant T5 (06- 06)

  • Page 26
    4. To lower the brush end, turn the shaft clockwise for the front brush and counter- clockwise for the rear brush. Retighten hex screw (Figure 61). FIG. 61 5. Recheck brush pattern. NOTE: Replace brushes when worn to 15mm. Tennant T5 (06- 06)

  • Page 27: Maintenance Chart

    Check and clean 750 Hours Vacuum fan motor Replace carbon brushes Disk brush motors Replace carbon brushes Propelling motor Replace carbon brushes 1000 Hours Cylindrical brush motors Replace carbon brushes FaST water and air filters Replace Tennant T5 (12- 13)

  • Page 28: Machine Maintenance

    Rinse and clean out the recovery tank (Figure 63). FIG. 67 FIG. 63 7. Rotate pad or replace when worn (Figure 68). 3. Remove the recovery tank float shut- off screen and clean (Figure 64). Disk Model FIG. 68 FIG. 64 Tennant T5 (12- 13)

  • Page 29
    71). Replace when worn to a length of 15mm. 13. Check the condition of the squeegee blade wiping edge (Figure 74). Rotate blade if worn (See SQUEEGEE BLADES). 15mm Cylindrical Brush Model FIG. 71 FIG. 74 Tennant T5 (06- 16)

  • Page 30: Monthly Maintenance

    Cylindrical Brush Model FIG. 79 2. Inspect and clean the recovery tank cover seal (Figure 80). Replace if damaged. FIG. 77 17. Recharge the batteries (Figure 78). See CHARGING BATTERIES. FIG. 80 Tennant T5 (06- 16)

  • Page 31: Battery Maintenance

    Add distilled water if low. DO NOT OVERFILL. The electrolyte will expand and may overflow when charging. After charging, distilled water can be added up to about 3 mm (0.12 in) below the sight tubes. FIG. 83 Tennant T5 (06- 16)

  • Page 32: Squeegee Blades

    (Figure 85). FIG. 87 MOTOR MAINTENANCE Replace motor carbon brushes as indicated. Contact trained personnel for carbon brush replacement. Carbon Brush Replacement Hours Drive Transaxle Motor Vacuum Motor Disk Brush Motors Cylindrical Brush Motors 1000 FIG. 85 Tennant T5 (12- 13)

  • Page 33: Fast System Maintenance

    (Figure 92). 3. Replace the water and air filter. An 8mm hex wrench is required to install the new water filter (Figure 90). Water Filter (50 Mesh/Brown) Gray Collar FIG. 92 Air Filter (50 Mesh/Brown) FIG. 90 Tennant T5 (06- 15)

  • Page 34: Ec- H2O Module Flush Procedure

    7 minute cycle in order to reset the system indicator light and alarm. FIG. 94 Repeat flush procedure if the ec- H2O module does not reset. If module fails to reset, contact an Authorized Service Center. Tennant T5 (06- 15)

  • Page 35: Jacking Up Machine

    5. Open the recovery tank cover to promote air circulation. ATTENTION: Do not expose machine to rain, store indoors. 6. If storing machine in freezing temperatures, follow the FREEZE PROTECTION instructions below. Tennant T5 (06- 16)

  • Page 36: Freeze Protection

    If the antifreeze is not properly flushed from the ec- H2O system, the ec- H2O module may detect an error and not function (ec- H2O switch indicator light will turn red). If this occurs, reset key and repeat the flush procedure as described below. Tennant T5 (06- 15)

  • Page 37: Troubleshooting

    Faulty control board Contact Service Center Wheels raised off floor Contact Service Center Faulty transaxle motor or wiring Contact Service Center Worn carbon brushes Contact Service Center Exceeded maximum incline Avoid steep inclines and reset key Tennant T5 (06- 06)

  • Page 38
    Replace battery Batteries need maintenance See BATTERY MAINTENANCE Faulty battery charger Repair or replace battery charger Solution flow and brush pressure Supervisor controls are activated Contact your Supervisor buttons and FaST system switch (lockout feature) are locked Tennant T5 (06- 06)
  • Page 39
    Defective module Contact Service Center solid red ec- H2O system indicator light Defective light or module Contact Service Center does not turn on No water flow Clogged module Contact Service Center Defective solution pump Replace solution pump Tennant T5 (06- 15)

  • Page 40: Control Panel Fault Indicator Codes

    Restart key to reset. All battery lights blink Emergency- Stop button activated Turn button clockwise to reset. All battery lights ripple Key turned on while bail was engaged. Release the control handle start bail. Tennant T5 (06- 06)

  • Page 41: General Machine Dimensions/Capacities/Performance

    SOUND POWER LEVEL 84 dBa 83 dBa +UNCERTAINTY K VIBRATION AT HAND- ARM* <2.5 m/s <2.5 m/s GRADE LEVEL, MAX. Scrubbing 5%, Transporting 8%, Ramp Loading (tanks empty) 19.5% * Values per EN 60335- 2- 72 Tennant T5 (12- 13)

  • Page 42: Machine Dimensions

    800 mm Disk Disk Disk Cylindrical Cylindrical 1.346 mm 1.400 mm 1.463 mm 1.387 mm 1.387 mm 645 mm 737 mm 838 mm 711 mm 864 mm 908 mm 1.051 mm 1.185 mm 1.051 mm 1.185 mm Tennant T5 (09- 08)

Источник

Достигните высочайшего уровня чистоты, гигиены и безопасности с поломоечной машиной Tennant T5

  • Берегите ресурсы! Чистите без химикатов с новой технологией ec-H2O™ — электрически активированная вода превращает воду в мощное чистящее средство
  • Берегите ресурсы! Чистите, используя на 90% меньше чистящего средства, и уменьшите размеры упаковки для химикатов на 80% с технологией FaST®
  • Берегите ресурсы! Уменьшите потребление воды на 90% и сократите неэффективное использование на 70% с технологией FaST®
  • Поломоечная машина tennant T5 уменьшает количество бактерий и налета благодаря легко очищаемым и легко доступным гигиеничным бакам
  • Низкий уровень шума в 67 дБ позволяет чистить в самых чувствительных к шуму местах
  • Улучшенная безопасность — поломоечная машина Tennant T5 полностью удаляет моющее средство, даже при повороте на 180 градусов, благодаря уникально спроектированному скребку

Ключевые характеристики производительности и надежности машины Tennant T5:

  • В машине Tennant Т5 установлены гигиеничные баки, уменьшающие количество плесени, бактерий и других загрязняющих веществ
  • Работающая от аккумуляторов поломоечная машина Tennant T5 практически не издает шума
  • Параболическая система скребка обладает оптимальным углом атаки, что позволяет полностью удалять остатки моющего средства
  • Технология FaST® использует до 70% меньше моющего средства во время чистки
  • Технология ec-H2O™ обеспечивает великолепный результат чистки без использования химикатов

Выберите лучшую технологию чистки для вашей среды

  • Новая технология ec-H2O™ — электрически активированная вода сокращает негативное влияние на окружающую среду: изготовление упаковки, транспортировку, использование и переработку химикатов
  • Технология FaST® — технология чистки пеной. Используя инновационную систему чистки пеной, поломоечные машины с FaST увеличивают производительность до 30%, уменьшают потребление воды до 70% и исключают необходимость контакта оператора с химикатами.

Tennant T5 – среднеразмерная производительная машина, для работы которой используется технология FaST®, снижающая объем химических моющих средств на 80%. Кроме того, значительно снижено потребление воды, улучшены показатели производительности, машина оборудована удобными гигиеническими баками.

Техника может использоваться для жилых помещений, офисов, торговых и развлекательных центров, салонов. В качестве источника питания установлена батарея на 24 В, общая мощность техники – 1200 Вт.

Особенности и преимущества модели Т5

Моющая машина T5 среднеразмерного класса отличается такими преимуществами:

  • производитель – до 1000-2500 кв.м/час;
  • ширина дорожки очистки – 60-70см;
  • скорость уборки (в зависимости от выбранного режима) – 2925-3600 кв.м/час;
  • низкий уровень шума – 67 ДБа;
  • простая замена щеток;
  • наличие технологии FaST® для экономного расхода воды и моющих средств;
  • автономность, благодаря установленному аккумулятору;
  • возможность использования модели с технологий ec-H2O.

Модель является самой мощной в среднеразмерном классе, она востребована для уборки офисов, развлекательных центров, жилых помещений, салонов и магазинов. Удобные щетки обеспечивают уборку мусора в труднодоступных места, машина работает от батареи, что обеспечивает ее автономность и мобильность.

Для заказа модели Т500 звоните нам по телефону: +7 (812) 425-62-66,  также Вы можете оставить онлайн-заявку на сайте с указанием своих контактных данных.

Источник

  • Contents

  • Table of Contents

  • Troubleshooting

  • Bookmarks

Quick Links

T5

Scrubber- -Dryer

Operator Manual

The Safe Scrubbing Alternativer

R

Hygenic

Fully Cleanable Tanks

QA Controlst Supervisor Settings

North America / International

9002326

Rev. 06 (11- -2008)

*9002326*

www.tennantco.com

loading

Related Manuals for Tennant T5

Summary of Contents for Tennant T5

  • Page 1
    Scrubber- -Dryer Operator Manual The Safe Scrubbing Alternativer Hygenic Fully Cleanable Tanks QA Controlst Supervisor Settings North America / International 9002326 Rev. 06 (11- -2008) *9002326* www.tennantco.com…
  • Page 2
    Phone: (800) 553- -8033 or (763) 513- -2850 www.tennantco.com FaSK—PAK and 1—STEP are US registered and unregistered trademarks of Tennant Company. Specifications and parts are subject to change without notice. Copyright E 2006, 2007, 2008 TENNANT COMPANY, Printed in U.S.A. All rights reserved. Tennant T5 (09- -08)

  • Page 3: Table Of Contents

    ….MACHINE DIMENSIONS ….Tennant T5 (11- -08)

  • Page 4: Safety Precautions

    Do not modify the machine from its original order to avoid a hazard. design. WARNING: Spinning Brush. Keep Hands Away. Turn Off Power Before Working On Machine. Tennant T5 (11- -08)

  • Page 5: Safety Labels

    Before Working On Machine. BATTERY CHARGE LABEL — — Located on bottom side of recovery tank. WARNING: Fire Or Explosion Hazard. Batteries Emit Hydrogen Gas. Keep Sparks And Open Flame Away. Keep Battery Compartment Open When Charging. Tennant T5 (06- -06)

  • Page 6: Machine Components

    11. Squeegee Assembly 25. Pad Driver Window 12. Solution Tank Clean-Out Port 26. Scrub Head Skirt 13. Recovery Tank Support Stand 27. Parking Brake (option) 14. Control Board 28. Cylindrical Brush Scrub Head 15. Bucket Fill Port/Clean—out Port Tennant T5 (09- -08)

  • Page 7: Control Panel Components

    6. Solution flow decrease button (—) 13. ec- -H2O system indicator light (ec- -H2O model) 7. Fault indicator — Contact Service 14. Main power on/off key switch 8. Supervisor control indicator — Lockout feature 15. Hour meter Tennant T5 (09- -08)

  • Page 8: Machine Installation

    (Figure 1). 13mm wrench required. IMPORTANT: If your machine is equipped with the on- -board battery charger, make sure that the charger is properly set for your battery type before charging (See ON- -BOARD CHARGER SETTINGS). Tennant T5 (06- -06)

  • Page 9: How The Machine Works

    Nylon fiber impregnated with abrasive grit to remove stains and soilage. Strong action on any surface. FIG. 5 Performs well on buildup, grease, or tire marks. Polishing Pad (White) — — Used to maintain highly polished or burnished floors. Tennant T5 (09- -08)

  • Page 10: Installing Brushes

    (Figure 8). FIG. 10 4. To remove the pad driver, raise the scrub head and push the pad release plunger downward (Figure 11). 2 mm 1/16” Lock Nut FIG. 8 FIG. 11 Tennant T5 (09- -08)

  • Page 11: Installing Fast—Pak

    (See ADJUSTING SCRUB HEAD FIG. 15 BRUSHES). 3. When the supply hose is not in use, connect the storage plug to prevent the FaST system from drying out and clogging up the hose (Figure 16). FIG. 16 Tennant T5 (06- -06)

  • Page 12: Filling Solution Tank

    ( I ) position (Figure 19). ec- H2O Model: Press the ec- -H2O system switch to the on ( I ) position (Figure 19). NOTE: The ec- -H2O system indicator light will not turn on until the machine starts scrubbing. Tennant T5 (03- -08)

  • Page 13
    (Figure 22). To reverse the machine, simply push the control handle bail forward. Raise squeegee when reversing machine. FIG. 24 9. To stop scrubbing, release the control handle bail, press the 1- -STEP scrub button and raise the squeegee. Tennant T5 (09- -08)

  • Page 14: Emergency Stopping

    PROCEDURE) (Figure 26). NOTE: When the alarm sounds and the light blinks red, FIG. 27 the machine will bypass the ec- -H2O system. To continue scrubbing, turn the ec- -H2O switch off and change over to conventional scrubbing. Tennant T5 (09- -08)

  • Page 15: Hour Meter

    1. Turn the key and wand switch to the on ( I ) 2. Connect the solution hose to the coupler at the position (Figure 32). The FaST/ec- -H2O system lower right side of machine (Figure 29). switch is disabled when operating the wand. FIG. 29 FIG. 32 Tennant T5 (09- -08)

  • Page 16: Draining And Cleaning Tanks

    WARNING: Fire or Explosion Hazard. Do Not Pick Up Flammable Materials Or Reactive Metals. FIG. 36 4. Clean the float shut-off screen and debris tray located in the recovery tank (Figure 37). FIG. 37 Tennant T5 (09- -08)

  • Page 17: Draining Solution Tank

    The charger will display a sequence of codes. One of the codes will either read “GEL” or “Acd” (Figure 41). GEL = Set for sealed/maintenance free batteries Acd = Set for wet/lead acid batteries FIG. 40 FIG. 41 Tennant T5 (06- -06)

  • Page 18: Using The On- -Board Battery Charger

    If the charger detects a problem, the charger will display an error code (See ON—BOARD BATTERY CHARGER ERROR CODES). FIG. 43 5. Connect the charger’s AC power supply cord into a properly grounded receptacle (Figure 44). Tennant T5 (09- -06)

  • Page 19: On—Board Battery Charger Error Codes

    E03 reappears check battery or re- sulfated or faulty battery. place it. Safety timer exceeded maximum charging Replace battery. time. Interrupts charging cycle. Possible internal short circuit. Contact Service Center. Tennant T5 (06- -07)

  • Page 20: On—Board Charger Fuse Replacement

    6. Connect the charger’s DC cord into the machine’s battery receptacle (Figure 50). FIG. 47 3. The fuse holder is located at the bottom of the charger. Use a screwdriver to access the fuse (Figure 48). FIG. 50 Tennant T5 (01- -07)

  • Page 21: Adjusting Scrub Head Brushes

    (Figure 54). FIG. 51 4. If scrub head is not level, loosen the lock nut and turn the scrub head leveling screw to level. Tighten down the lock nut once head is level (Figure 52). FIG. 54 Tennant T5 (01- -07)

  • Page 22
    Retighten hex screw (Figure 59). FIG. 56 3. Recheck brush pattern. FIG. 59 NOTE: Replace brushes when worn to 5/8” (15mm). 5. Recheck brush pattern. NOTE: Replace brushes when worn to 5/8” (15mm). Tennant T5 (01- -07)

  • Page 23: Machine Maintenance

    Clean the solution tank filter (Figure 65). FIG. 61 FIG. 65 3. Remove the recovery tank float shut—off screen and clean (Figure 62). 7. Rotate pad or replace when worn (Figure 66). Disk Model FIG. 62 FIG. 66 Tennant T5 (01- -07)

  • Page 24
    13. Clean the machine with an all purpose cleaner and plates and drive hubs (Figure 69). damp cloth (Figure 72). FOR SAFETY: When cleaning machine, do not power spray or hose off machine. Electrical malfunction may occur. Cylindrical Brush Model FIG. 69 FIG. 72 Tennant T5 (01- -07)

  • Page 25: Monthly Maintenance

    3. Lubricate all pivot points and rollers with a water the machine was used for a total of 30 minutes or resistant grease. more. 4. Lubricate the casters with a water resistant grease (Figure 78). FIG. 75 FIG. 78 Tennant T5 (06- -07)

  • Page 26: Battery Maintenance

    2. Clean the batteries to prevent battery corrosion. Use a scrub brush with a mixture of baking soda and water (Figure 80). FOR SAFETY: When cleaning batteries, wear protective gloves and eye protection. Avoid contact with battery acid. FIG. 82 Tennant T5 (01- -07)

  • Page 27: Motor Maintenance

    (Figure 87). Vacuum Motor Water Filter Disk Brush Motors (50 Mesh/Brown) Cylindrical Brush Motors 1000 WARNING: Electrical Hazard. Disconnect Battery Cables Before Servicing Machine. Air Filter (50 Mesh/Brown) FIG. 87 Tennant T5 (03- -08)

  • Page 28: Ec—H2O Module Flush Procedure

    FOR SAFETY: When servicing machine, jack machine up at designated locations only. Use jack FIG. 88 or hoist that will support machine weight. 4. Turn the key to the on ( I ) position. FIG. 90 Tennant T5 (11- -08)

  • Page 29: Transporting Machine

    2. Fill the solution tank with cool water until full (See FILLING SOLUTION TANK). 4. Open the recovery tank cover to promote air circulation. ATTENTION: Do not expose machine to rain, store indoors. 5. If storing machine in freezing temperatures, follow the FREEZE PROTECTION instructions below. Tennant T5 (09- -08)

  • Page 30
    FIG. 97 detergent from the hose (Figure 95). Reconnect the hose after draining. To access the injector 10. To drain the antifreeze from the FaST supply hose, assembly remove the front cover. repeat steps 1 and 2. Tennant T5 (09- -08)

  • Page 31: Recommended Stock Items

    Contact Service Center Faulty transaxle motor or wiring Contact Service Center Worn carbon brushes Contact Service Center Exceeded maximum incline Avoid steep inclines and reset key Vacuum motor will not Squeegee is raised off floor Lower squeegee operate Tennant T5 (11- -08)

  • Page 32
    Batteries need maintenance See BATTERY MAINTENANCE Faulty battery charger Repair or replace battery charger Solution flow and brush Supervisor controls are activated (lock- Contact your Supervisor pressure buttons and out feature) FaST system switch are locked Tennant T5 (06- -06)
  • Page 33
    H2O Model: Defective light or module Contact Service Center ec- -H2O system indicator light does not turn on ec- H2O Model: Clogged module Contact Service Center No water flow Defective solution pump Replace solution pump Tennant T5 (09- -08)

  • Page 34: Control Panel Fault Indicator Codes

    Restart key to reset. All battery lights blink Emergency—Stop button activated Turn button clockwise to reset. All battery lights ripple Key turned on while bail was engaged. Release the control handle start bail. Tennant T5 (06- -06)

  • Page 35: Machine Specifications

    GRADE LEVEL, MAX. Scrubbing 5% (3°), Transporting 8% (5°) * Run times are based on Continuous Scrubbing Run Times. ** Sound pressure (ISO 11201) as recommended by the American Association of Cleaning Equipment Manufacturers (AACEM) and OSHA. Tennant T5 (06- -07)

  • Page 36
    0.83 L/min 1.14 L/min 1.67 L/min (optional) (optional) (optional) (optional) 0.30 gpm / 0.44 gpm / 1.67 L/min 1.14 L/min (optional) (optional) * If the optional solution flow rates are required, contact an Authorized Service Center. Tennant T5 (09- -08)

  • Page 37: Machine Dimensions

    33 in / 838 mm 28 in / 711 mm 34 in / 864 mm 35.7 in / 908 mm 41.3 in / 1,051 mm 46.6 in / 1,185 mm 41.3 in / 1,051 mm 46.6 in / 1,185 mm Tennant T5 (06- -07)

Источник

  • Contents

  • Table of Contents

  • Troubleshooting

  • Bookmarks

Quick Links

T5

Scrubber- -Dryer

Operator Manual

The Safe Scrubbing Alternativer

R

Hygenic

Fully Cleanable Tanks

QA Controlst Supervisor Settings

North America / International

9002326

Rev. 06 (11- -2008)

*9002326*

www.tennantco.com

loading

Related Manuals for Tennant T5

Summary of Contents for Tennant T5

  • Page 1
    Scrubber- -Dryer Operator Manual The Safe Scrubbing Alternativer Hygenic Fully Cleanable Tanks QA Controlst Supervisor Settings North America / International 9002326 Rev. 06 (11- -2008) *9002326* www.tennantco.com…
  • Page 2
    Phone: (800) 553- -8033 or (763) 513- -2850 www.tennantco.com FaSK—PAK and 1—STEP are US registered and unregistered trademarks of Tennant Company. Specifications and parts are subject to change without notice. Copyright E 2006, 2007, 2008 TENNANT COMPANY, Printed in U.S.A. All rights reserved. Tennant T5 (09- -08)

  • Page 3: Table Of Contents

    ….MACHINE DIMENSIONS ….Tennant T5 (11- -08)

  • Page 4: Safety Precautions

    Do not modify the machine from its original order to avoid a hazard. design. WARNING: Spinning Brush. Keep Hands Away. Turn Off Power Before Working On Machine. Tennant T5 (11- -08)

  • Page 5: Safety Labels

    Before Working On Machine. BATTERY CHARGE LABEL — — Located on bottom side of recovery tank. WARNING: Fire Or Explosion Hazard. Batteries Emit Hydrogen Gas. Keep Sparks And Open Flame Away. Keep Battery Compartment Open When Charging. Tennant T5 (06- -06)

  • Page 6: Machine Components

    11. Squeegee Assembly 25. Pad Driver Window 12. Solution Tank Clean-Out Port 26. Scrub Head Skirt 13. Recovery Tank Support Stand 27. Parking Brake (option) 14. Control Board 28. Cylindrical Brush Scrub Head 15. Bucket Fill Port/Clean—out Port Tennant T5 (09- -08)

  • Page 7: Control Panel Components

    6. Solution flow decrease button (—) 13. ec- -H2O system indicator light (ec- -H2O model) 7. Fault indicator — Contact Service 14. Main power on/off key switch 8. Supervisor control indicator — Lockout feature 15. Hour meter Tennant T5 (09- -08)

  • Page 8: Machine Installation

    (Figure 1). 13mm wrench required. IMPORTANT: If your machine is equipped with the on- -board battery charger, make sure that the charger is properly set for your battery type before charging (See ON- -BOARD CHARGER SETTINGS). Tennant T5 (06- -06)

  • Page 9: How The Machine Works

    Nylon fiber impregnated with abrasive grit to remove stains and soilage. Strong action on any surface. FIG. 5 Performs well on buildup, grease, or tire marks. Polishing Pad (White) — — Used to maintain highly polished or burnished floors. Tennant T5 (09- -08)

  • Page 10: Installing Brushes

    (Figure 8). FIG. 10 4. To remove the pad driver, raise the scrub head and push the pad release plunger downward (Figure 11). 2 mm 1/16” Lock Nut FIG. 8 FIG. 11 Tennant T5 (09- -08)

  • Page 11: Installing Fast—Pak

    (See ADJUSTING SCRUB HEAD FIG. 15 BRUSHES). 3. When the supply hose is not in use, connect the storage plug to prevent the FaST system from drying out and clogging up the hose (Figure 16). FIG. 16 Tennant T5 (06- -06)

  • Page 12: Filling Solution Tank

    ( I ) position (Figure 19). ec- H2O Model: Press the ec- -H2O system switch to the on ( I ) position (Figure 19). NOTE: The ec- -H2O system indicator light will not turn on until the machine starts scrubbing. Tennant T5 (03- -08)

  • Page 13
    (Figure 22). To reverse the machine, simply push the control handle bail forward. Raise squeegee when reversing machine. FIG. 24 9. To stop scrubbing, release the control handle bail, press the 1- -STEP scrub button and raise the squeegee. Tennant T5 (09- -08)

  • Page 14: Emergency Stopping

    PROCEDURE) (Figure 26). NOTE: When the alarm sounds and the light blinks red, FIG. 27 the machine will bypass the ec- -H2O system. To continue scrubbing, turn the ec- -H2O switch off and change over to conventional scrubbing. Tennant T5 (09- -08)

  • Page 15: Hour Meter

    1. Turn the key and wand switch to the on ( I ) 2. Connect the solution hose to the coupler at the position (Figure 32). The FaST/ec- -H2O system lower right side of machine (Figure 29). switch is disabled when operating the wand. FIG. 29 FIG. 32 Tennant T5 (09- -08)

  • Page 16: Draining And Cleaning Tanks

    WARNING: Fire or Explosion Hazard. Do Not Pick Up Flammable Materials Or Reactive Metals. FIG. 36 4. Clean the float shut-off screen and debris tray located in the recovery tank (Figure 37). FIG. 37 Tennant T5 (09- -08)

  • Page 17: Draining Solution Tank

    The charger will display a sequence of codes. One of the codes will either read “GEL” or “Acd” (Figure 41). GEL = Set for sealed/maintenance free batteries Acd = Set for wet/lead acid batteries FIG. 40 FIG. 41 Tennant T5 (06- -06)

  • Page 18: Using The On- -Board Battery Charger

    If the charger detects a problem, the charger will display an error code (See ON—BOARD BATTERY CHARGER ERROR CODES). FIG. 43 5. Connect the charger’s AC power supply cord into a properly grounded receptacle (Figure 44). Tennant T5 (09- -06)

  • Page 19: On—Board Battery Charger Error Codes

    E03 reappears check battery or re- sulfated or faulty battery. place it. Safety timer exceeded maximum charging Replace battery. time. Interrupts charging cycle. Possible internal short circuit. Contact Service Center. Tennant T5 (06- -07)

  • Page 20: On—Board Charger Fuse Replacement

    6. Connect the charger’s DC cord into the machine’s battery receptacle (Figure 50). FIG. 47 3. The fuse holder is located at the bottom of the charger. Use a screwdriver to access the fuse (Figure 48). FIG. 50 Tennant T5 (01- -07)

  • Page 21: Adjusting Scrub Head Brushes

    (Figure 54). FIG. 51 4. If scrub head is not level, loosen the lock nut and turn the scrub head leveling screw to level. Tighten down the lock nut once head is level (Figure 52). FIG. 54 Tennant T5 (01- -07)

  • Page 22
    Retighten hex screw (Figure 59). FIG. 56 3. Recheck brush pattern. FIG. 59 NOTE: Replace brushes when worn to 5/8” (15mm). 5. Recheck brush pattern. NOTE: Replace brushes when worn to 5/8” (15mm). Tennant T5 (01- -07)

  • Page 23: Machine Maintenance

    Clean the solution tank filter (Figure 65). FIG. 61 FIG. 65 3. Remove the recovery tank float shut—off screen and clean (Figure 62). 7. Rotate pad or replace when worn (Figure 66). Disk Model FIG. 62 FIG. 66 Tennant T5 (01- -07)

  • Page 24
    13. Clean the machine with an all purpose cleaner and plates and drive hubs (Figure 69). damp cloth (Figure 72). FOR SAFETY: When cleaning machine, do not power spray or hose off machine. Electrical malfunction may occur. Cylindrical Brush Model FIG. 69 FIG. 72 Tennant T5 (01- -07)

  • Page 25: Monthly Maintenance

    3. Lubricate all pivot points and rollers with a water the machine was used for a total of 30 minutes or resistant grease. more. 4. Lubricate the casters with a water resistant grease (Figure 78). FIG. 75 FIG. 78 Tennant T5 (06- -07)

  • Page 26: Battery Maintenance

    2. Clean the batteries to prevent battery corrosion. Use a scrub brush with a mixture of baking soda and water (Figure 80). FOR SAFETY: When cleaning batteries, wear protective gloves and eye protection. Avoid contact with battery acid. FIG. 82 Tennant T5 (01- -07)

  • Page 27: Motor Maintenance

    (Figure 87). Vacuum Motor Water Filter Disk Brush Motors (50 Mesh/Brown) Cylindrical Brush Motors 1000 WARNING: Electrical Hazard. Disconnect Battery Cables Before Servicing Machine. Air Filter (50 Mesh/Brown) FIG. 87 Tennant T5 (03- -08)

  • Page 28: Ec—H2O Module Flush Procedure

    FOR SAFETY: When servicing machine, jack machine up at designated locations only. Use jack FIG. 88 or hoist that will support machine weight. 4. Turn the key to the on ( I ) position. FIG. 90 Tennant T5 (11- -08)

  • Page 29: Transporting Machine

    2. Fill the solution tank with cool water until full (See FILLING SOLUTION TANK). 4. Open the recovery tank cover to promote air circulation. ATTENTION: Do not expose machine to rain, store indoors. 5. If storing machine in freezing temperatures, follow the FREEZE PROTECTION instructions below. Tennant T5 (09- -08)

  • Page 30
    FIG. 97 detergent from the hose (Figure 95). Reconnect the hose after draining. To access the injector 10. To drain the antifreeze from the FaST supply hose, assembly remove the front cover. repeat steps 1 and 2. Tennant T5 (09- -08)

  • Page 31: Recommended Stock Items

    Contact Service Center Faulty transaxle motor or wiring Contact Service Center Worn carbon brushes Contact Service Center Exceeded maximum incline Avoid steep inclines and reset key Vacuum motor will not Squeegee is raised off floor Lower squeegee operate Tennant T5 (11- -08)

  • Page 32
    Batteries need maintenance See BATTERY MAINTENANCE Faulty battery charger Repair or replace battery charger Solution flow and brush Supervisor controls are activated (lock- Contact your Supervisor pressure buttons and out feature) FaST system switch are locked Tennant T5 (06- -06)
  • Page 33
    H2O Model: Defective light or module Contact Service Center ec- -H2O system indicator light does not turn on ec- H2O Model: Clogged module Contact Service Center No water flow Defective solution pump Replace solution pump Tennant T5 (09- -08)

  • Page 34: Control Panel Fault Indicator Codes

    Restart key to reset. All battery lights blink Emergency—Stop button activated Turn button clockwise to reset. All battery lights ripple Key turned on while bail was engaged. Release the control handle start bail. Tennant T5 (06- -06)

  • Page 35: Machine Specifications

    GRADE LEVEL, MAX. Scrubbing 5% (3°), Transporting 8% (5°) * Run times are based on Continuous Scrubbing Run Times. ** Sound pressure (ISO 11201) as recommended by the American Association of Cleaning Equipment Manufacturers (AACEM) and OSHA. Tennant T5 (06- -07)

  • Page 36
    0.83 L/min 1.14 L/min 1.67 L/min (optional) (optional) (optional) (optional) 0.30 gpm / 0.44 gpm / 1.67 L/min 1.14 L/min (optional) (optional) * If the optional solution flow rates are required, contact an Authorized Service Center. Tennant T5 (09- -08)

  • Page 37: Machine Dimensions

    33 in / 838 mm 28 in / 711 mm 34 in / 864 mm 35.7 in / 908 mm 41.3 in / 1,051 mm 46.6 in / 1,185 mm 41.3 in / 1,051 mm 46.6 in / 1,185 mm Tennant T5 (06- -07)

Источник

0 0 голоса
Рейтинг статьи
Подписаться
Уведомить о
guest

0 комментариев
Старые
Новые Популярные
Межтекстовые Отзывы
Посмотреть все комментарии

А вот еще интересные материалы:

  • Яшка сломя голову остановился исправьте ошибки
  • Ясность цели позволяет целеустремленно добиваться намеченного исправьте ошибки
  • Ясность цели позволяет целеустремленно добиваться намеченного где ошибка
  • Tenda код ошибки 678
  • Tempro 300 ошибка ah

    • ➤