Researchdownload ошибка incompatible partition

Инструкция по прошивке Spreadtrum смартфонов через Research Download

Инструкция по прошивке смартфона на чипсете Spreadtrum через ResearchDownload

Что нам понадобится:

Инструкция по установке .pac прошивки целиком:

1. Скачайте из вложений архив RESEARCHDOWNLOAD_2.9.7003.zip и распакуйте его. Из распакованного архива, на правах администратора (правый клик по файлу -> запуск от имени администратора), запустите файл ResearchDownload.exe

2. Появится окно программы, нажмите на значёк одной шестерёнки расположенный в левом верхнем углу программы. Появится окно обзора, выберите вашу прошивку в формате .pac

3. После выбора прошивки, программа «подвиснет» на некоторое время и после этого имя загруженной прошивки отобразится в верхней части программы

4. Далее, убедитесь что ваше устройство отключено от ПК и нажмите значёк Play (стрелка вроде «>») в окне ResearchDownload, чтобы перевести программу в режим ожидания подключения смартфона

5. Далее берём наш смартфон в руки, выключаем его полностью. Если у вас съёмная батарея, то вытащите её и вставьте обратно, но не включайте смартфон, если батарея несъёмная, то можно пропустить данный пункт. Итак, после того как «передёрнули» батарею, подключаем смартфон к компьютеру и при этом держим кнопку уменьшения звука.

6. После подключения смартфона, как описано ниже, в окне программы ResearchDownload, должна будет начаться прошивка, как только она стартует, можно будет отпустить кнопку уменьшения звука и просто дождаться завершения прошивки. Если прошивка не стартует, то, скорее всего не установлены драйвера. После завершения прошивки вы увидите надпись «Passed», после этого можно отключить смартфон (рекомендую еще раз «передёрнуть» батарею») и запустить его. Имейте в виду что после перепрошивки, первый старт смартфона, может длиться долльше обычного (не паникуйте сразу).

Источник

Prestigio PSP5502DUO требует _REPARTITION_

Assists

======= Flash
Files set for flashing :
[ MCU ] : SC7731_TE50B3G_5.1_PSP5502DUO.20160405.1.0.06_PSP5502DUO.pac
CRVersion : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : SC7731_eMMC_TE50B3G_5.1_PSP5502DUO.20160405.1.0.06_PSP5502DU_INFINITY-BOX
File : Infinity_fdl1.bin
File : Infinity_fdl2.bin
File : nvitem_w.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : sc7731g_CP0_modem.bin
File : DSP_DM_Gx.bin
File : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
File : logo_720x1280.bin
File : fblogo_720x1280.bin
File : boot.img
File : system.img
File : cache.img
File : recovery.img
File : userdata.img
File : u-boot.bin

1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
-> Alternative : just ONE ‘VolumeUp’ or ‘VolumeDown’ key
3. Insert cable

Phone found! [ 19 ]
Port Opened
Sync.
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync.
Sending FDL
[Info] : If SW freeze here more, than 15 seconds — remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
PMTManager : Load 0x18 records
PMTManager : PMT Update Failed.
Selected firmware doesn’t match to current HW or EMPTY battery!
Flashing terminated!

Connecting to the SD/eMMC Card. OK
Выставленное I/O Напряжение 1.79V, SD_CLK Frequency is 6 MHz

Memory Type . eMMC
Manufacturer ID . 0x90
OEM/Application ID . 0x4A
Product Name . «H8G1e »
Package . BGA
User Area Partition Size . 0x0001D2000000 Bytes (7.28 GB)
Boot Partition Size . 0x000000400000 Bytes (4.00 MB)
RPMB Partition Size . 0x000000400000 Bytes (4.00 MB)
OCR Register . 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits . NONE
ExtCSD Register Fields . [177] = 0x00 , [179] = 0x08 , [162] = 0x00
Boot Configuration . Boot from Boot Partition 1 (Bus Width = 1 Bit)
Chip Revision . 0.7
Multimedia Card Revision . 1.7 (eMMC v5.0)
Serial Number . 0x32144835
Memory Manufacturing Date . April, 2016

Источник

Repartition failed operation failed при прошивке research download

Below is a comprehensive list of Research / Upgrade Download tool errors, what they mean and how to fix them. We’ll keep building this list to ensure it captures all errors and proffers effective solutions. Ensure to see the tutorial on how to use Research Download tool / Upgrade Download tool to be sure you’re doing it right else you’ll keep running into error after error. Research Download tool & Upgrade Download tool are Windows desktop applications for flashing firmware / pac files to Spreadtrum (SPD) Android devices.

Phone is totally dead

Message: The phone doesnt respond to power button or only vibrates after pressing the power button but doesnt come on

Meaning: The OS is either corrupted or there’s no power to boot the phone

Solution:

• Ensure the battery is well charged
• Re-flash the pac file

Research / Upgrade download tool does not show waiting. instead, the phone just charges

Message: After you click Start and connect the phone to the PC, the tool doesn’t show waiting. Instead, the phone begins charging or shows a charging sign. You could sometimes get the USB connection-disconnection sound on the PC

Meaning: The Spreadtrum drivers have not been properly associated with the device

Solution:

• Launch Device manager (Right-click My Computer > Select Manage)
• Connect the phone to the PC via a USB cord, Device manager should refresh
• Take note of what the phone is detected as (often as Unknown or Spreadtrum under Other devices)
• Right-click whatever the phone is detect as and select Update Driver Software.
• Select Browse my computer for driver software
• Select Let me pick from a list of device drivers on my computer
• Click Next
• Click Have Disk
• Proceed with the Spreadtrum (SCiU2S) driver installation steps described at https://www.hovatek.com/forum/thread-827.html and click Yes if you get an Update Driver warning

Progress bar stuck at waiting.

Message: After clicking Start Downloading and connecting the phone, the Progress bar gets stuck at Waiting.

Meaning: The tools is having problems finding the phone

Solution:

• Ensure the phone is switched off with a charged battery inside before connecting to PC for flashing
• Ensure to install Spreadtrum drivers before flashing (see https://www.hovatek.com/forum/thread-827.html)
• Try using a different USB cord, PC port or PC
• Try holding the volume decrease button while connecting to PC for flashing. You could try the Volume increase button also

Failed: NV data in device is crashed

Message: Failed: NV data in phone is crashed

Meaning: The tool is unable to properly read nv data items on the phone

Solution:

• Retry flashing using upgrade download tool or factory download tool @ https://www.hovatek.com/forum/thread-15611.html

Failed: NV data read in phone is crashed

Message: Failed:NV data read in phone is crashed

Meaning: The NV items (Calibration) are causing a clash

USB device not recognized

Message: USB device not recognized prompt at system tray after connecting the phone to PC

Meaning: The PC is having problems communicating with the phone (often due to interruption, hardware or driver problems)

Solution:

• Try a different USB cord, PC port or PC
• Re-install Spreadtrum drivers (see https://www.hovatek.com/forum/thread-827.html)
• Ensure the phone is switched off before connecting to PC for flashing (take out the battery and slot back in to be sure)

Failed: Operation failed

Message: Failed: Operation failed error during flashing

Meaning: An error was encountered during flashing

Solution:

• Flash one file at a time (fdl 1 & 2 are required so the third will be selected one at a time from the remaining files)
• Ensure the flashing process isn’t interrupted by a shaky USB cord / Port
• Try using a higher version of Research Download tool
• Try a different pac file

Failed: download size error

Message: Failed: download size error

Meaning: There was a problem flashing a file to its assigned partition due to its size

Solution:

• Flash one file at a time (fdl 1 & 2 are required so the third will be selected one at a time from the remaining files)
• Try a different pac file
• Use the latest version of Research Download tool or Upgrade Download tool (V r2.9.9008 and above)

Downloading failed : wait input time out / remote data too large

Message: Downloading failed : wait input time out
Meaning: A timeout was reached as a result of the flashing process taking too long

Solution:

• Use the latest version of Research Download tool or Upgrade Download tool (V r2.9.9008 and above)

Failed incompatible partition

Message: Failed incompatible partition

Meaning: There was an error flashing to certain partitions

Solution:

• Go to Settings > Options > Option . Tick Repartition
• Use the latest version of Research Download tool or Upgrade Download tool (V r2.9.9008 and above)
• Flash one item at a time (fdl 1&2 are constant)
• Flash using a different tool e.g Miracle box, CM2SPD, or any other with support for flashing SPD phones

Stuck at checking Bautrate

Message: Checking Bautrate

Meaning: The tool encountered an error initializing flashing

Solution:

• Disconnect the phone from the PC, take out the battery and slot back in
• Close Research Download / Upgrade download tool and relaunch

Failed: buffer error

Message: Failed: decode or verify received buffer error

Meaning: The tool encountered a problem flashing the pac file

Solution:

• Download the latest version of Research Download or Upgrade Download tool @ https://www.hovatek.com/forum/thread-15611.html

Failed: uart send error

Message: [Removed] Failed: uart send error

Meaning: The flashing process got interrupted

Solution:

• Try using a different USB cord, port and PC
• Download the latest version of Research Download or Upgrade Download tool @ https://www.hovatek.com/forum/thread-15611.html
• Try flashing with Miracle Box
• Ensure to hold the Volume down button when connecting to the PC for flashing
• Try changing the phone’s USB port

The second enumeration port timeout

Message: Failed: The second enumeration port timeout

Meaning: There was an error maintaining communication to the device

Solution:

• Try using a different USB cord, port and PC

Image size is over its partition

Message: Failed: Image size is over its partition

Meaning: One or more of the files in the firmware (pac file) is too large

Solution:

• Try a different firmware
• Untick traditionally large partitions like system and userdata

Failed: User cancel

Message: Failed: User cancel

Meaning: The flashing process was interrupted by holding or releasing the volume down button at the wrong time

Solution:

• Ensure to hold the volume down button when connecting to PC for flashing and don’t release till flashing is complete

Failed: . GSM Cali in phone is not calibrated.Reserved[7]:0x00000000,[ID=0x2]

Message: Failed: . GSM Cali in phone is not calibrated.Reserved[7]:0x00000000,[ID=0x2]

Meaning: The tool is unable to read the calibration data off the device or the device isn’t properly calibrated

Solution:

• Try a different version of Research Download tool or Upgrade Download tool @ https://www.hovatek.com/forum/thread-15611.html

Failed: Open port fail

Message: Failed: Open port fail

Meaning: The tool encountered an error while communicating with the phone

Solution:

• Disconnect the phone from the PC, take out the battery and slot back in then ensure to hold the Volume down button when connecting to the PC for flashing
• Try a different cord, port and PC

_REPARTITION_ error

Message: Failed: Operation failed

Meaning: The tool encountered a partition table error while trying to flash the device

Solution:
Use Factory Download tool @ https://www.hovatek.com/forum/thread-15611.html or a box / dongle which supports your Spreadtrum chipset

Update Driver error

Message: Your driver version is *****, it is too low. Please upgrade download driver.

Meaning: The tool detects you still have an old driver and won’t proceed until its updated

Solution:
Download and install any driver from ‘version 2015″ upwards @ https://www.hovatek.com/forum/thread-26658.html

Flashing failed or stuck at System.img

Meaning: The tool encountered an error while trying to flash system.img

Failed: the data packet with type(0x96) returned was misformatted

Message: Failed: the data packet with type(0x96) returned was misformatted

Meaning: The tool is unable to proceed with flashing the specified firmware

ReadPartition Finish

Message: Failed: Software has not supported this feature

Meaning: A backup setting is interfering with flashing

Solution:

• In Research Download, go to Settings > Options > Read Option and untick Read Partition

Bin packet version is not support

Message: Bin packet version is not support! Load bin packet failed!

Meaning: You’re either using an old version of the tool or an improperly built pac file
Solution:

• Try using the latest version of Research / Upgrade / Factory download tool
• Ensure you’re using a valid pac file

Источник

Below is a comprehensive list of Research / Upgrade Download tool errors, what they mean and how to fix them. We’ll keep building this list to ensure it captures all errors and proffers effective solutions. Ensure to see the tutorial on how to use Research Download tool  / Upgrade Download tool to be sure you’re doing it right else you’ll keep running into error after error. Research Download tool & Upgrade Download tool are Windows desktop applications for flashing firmware / pac files to Spreadtrum (SPD) Android devices.

List of Research Download tool  / Upgrade Download tool errors and their solutions

Phone is totally dead

Message: The phone doesnt respond to power button or only vibrates after pressing the power button but doesnt come on

Meaning: The OS is either corrupted or there’s no power to boot the phone

Solution:

• Ensure the battery is well charged
• Re-flash the pac file

Research / Upgrade download tool does not show waiting…. instead, the phone just charges

Message: After you click Start and connect the phone to the PC, the tool doesn’t show waiting. Instead, the phone begins charging or shows a charging sign. You could sometimes get the USB connection-disconnection sound on the PC

Meaning: The Spreadtrum drivers have not been properly associated with the device

Solution:

• Launch Device manager (Right-click My Computer > Select Manage)
• Connect the phone to the PC via a USB cord, Device manager should refresh
• Take note of what the phone is detected as (often as Unknown or Spreadtrum under Other devices)
• Right-click whatever the phone is detect as and select Update Driver Software…
• Select Browse my computer for driver software
• Select Let me pick from a list of device drivers on my computer
• Click Next
• Click Have Disk
• Proceed with the Spreadtrum (SCiU2S) driver installation steps described at https://www.hovatek.com/forum/thread-827.html and click Yes if you get an Update Driver warning

Progress bar stuck at waiting….

Message: After clicking Start Downloading and connecting the phone, the Progress bar gets stuck at Waiting…

Meaning: The tools is having problems finding the phone

Solution:

• Ensure the phone is switched off with a charged battery inside before connecting to PC for flashing
• Ensure to install Spreadtrum drivers before flashing (see https://www.hovatek.com/forum/thread-827.html)
• Try using a different USB cord, PC port or PC
• Try holding the volume decrease button while connecting to PC for flashing. You could try the Volume increase button also

Failed: NV data in device is crashed

Message: Failed: NV data in phone is crashed

Meaning: The tool is unable to properly read nv data items on the phone

Solution:

• Retry flashing using upgrade download tool or factory download tool @ https://www.hovatek.com/forum/thread-15611.html

Failed: NV data read in phone is crashed

Message: Failed:NV data read in phone is crashed

Meaning: The NV items (Calibration) are causing a clash

Solution:

• Follow this guide @ https://www.hovatek.com/forum/thread-2718.html

USB device not recognized

Message: USB device not recognized prompt at system tray after connecting  the phone to PC

Meaning: The PC is having problems communicating with the phone (often due to interruption, hardware or driver problems)

Solution:

• Try a different USB cord, PC port or PC
• Re-install Spreadtrum drivers (see https://www.hovatek.com/forum/thread-827.html)
• Ensure the phone is switched off before connecting to PC for flashing (take out the battery and slot back in to be sure)

Failed: Operation failed

Message: Failed: Operation failed error during flashing

Meaning: An error was encountered during flashing

Solution:

• Flash one file at a time (fdl 1 & 2 are required so the third will be selected one at a time from the remaining files)
• Ensure the flashing process isn’t interrupted by a shaky USB cord / Port
• Try using a higher version of Research Download tool
• Try a different pac file

Failed: download size error

Message: Failed: download size error

Meaning: There was a problem flashing a file to its assigned partition due to its size

Solution:

• Flash one file at a time (fdl 1 & 2 are required so the third will be selected one at a time from the remaining files)
• Try a different pac file
• Use the latest version of Research Download tool or Upgrade Download tool (V r2.9.9008 and above)

Downloading failed : wait input time out / remote data too large

Message: Downloading failed : wait input time out
Meaning: A timeout was reached as a result of the flashing process taking too long

Solution:

• Use the latest version of Research Download tool or Upgrade Download tool (V r2.9.9008 and above)

Failed incompatible partition

Message: Failed incompatible partition

Meaning: There was an error flashing to certain partitions

Solution:

• Go to Settings > Options > Option . Tick Repartition
• Use the latest version of Research Download tool or Upgrade Download tool (V r2.9.9008 and above)
• Flash one item at a time (fdl 1&2 are constant)
• Flash using a different tool e.g Miracle box, CM2SPD, or any other with support for flashing SPD phones

Stuck at checking Bautrate

Message: Checking Bautrate

Meaning: The tool encountered an error initializing flashing

Solution:

• Disconnect the phone from the PC, take out the battery and slot back in
• Close Research Download / Upgrade download tool and relaunch

Failed: buffer error

Message: Failed: decode or verify received buffer error

Meaning: The tool encountered a problem flashing the pac file

Solution:

• Download the latest version of Research Download or Upgrade Download tool @ https://www.hovatek.com/forum/thread-15611.html

Failed: uart send error

Message: [Removed] Failed: uart send error

Meaning: The flashing process got interrupted

Solution:

• Try using a different USB cord, port and PC
• Download the latest version of Research Download or Upgrade Download tool @ https://www.hovatek.com/forum/thread-15611.html
• Try flashing with Miracle Box
• Ensure to hold the Volume down button when connecting to the PC for flashing
• Try changing the phone’s USB port

The second enumeration port timeout

Message: Failed: The second enumeration port timeout

Meaning: There was an error maintaining communication to the device

Solution:

• Try using a different USB cord, port and PC

Image size is over its partition

Message: Failed: Image size is over its partition

Meaning: One or more of the files in the firmware (pac file) is too large

Solution:

• Try a different firmware
• Untick traditionally large partitions like system and userdata

Failed: User cancel

Message: Failed: User cancel

Meaning: The flashing process was interrupted by holding or releasing the volume down button at the wrong time

Solution:

• Ensure to hold the volume down button when connecting to PC for flashing and don’t release till flashing is complete

Failed: !!!GSM Cali in phone is not calibrated.Reserved[7]:0x00000000,[ID=0x2]

Message: Failed: !!!GSM Cali in phone is not calibrated.Reserved[7]:0x00000000,[ID=0x2]

Meaning: The tool is unable to read the calibration data off the device or the device isn’t properly calibrated

Solution:

• Try a different version of Research Download tool or Upgrade Download tool @ https://www.hovatek.com/forum/thread-15611.html

Failed: Open port fail

Message: Failed: Open port fail

Meaning: The tool encountered an error while communicating with the phone

Solution:

• Disconnect the phone from the PC, take out the battery and slot back in then ensure to hold the Volume down button when connecting to the PC for flashing
• Try a different cord, port and PC

_REPARTITION_ error

Message: Failed: Operation failed

Meaning: The tool encountered a partition table error while trying to flash the device

Solution:
Use Factory Download tool @ https://www.hovatek.com/forum/thread-15611.html or a box / dongle which supports your Spreadtrum chipset

Update Driver error

Message: Your driver version is *****, it is too low. Please upgrade download driver!!!

Meaning: The tool detects you still have an old driver and won’t proceed until its updated

Solution:
Download and install any driver from ‘version 2015″ upwards @ https://www.hovatek.com/forum/thread-26658.html

Flashing failed or stuck at System.img

Message: Failed

Meaning: The tool encountered an error while trying to flash system.img

Solution:
Use Research Download tool @ https://www.hovatek.com/forum/thread-15611.html

Failed: the data packet with type(0x96) returned was misformatted

Message: Failed: the data packet with type(0x96) returned was misformatted

Meaning: The tool is unable to proceed with flashing the specified firmware

Solution:

• Try flashing using factory download tool @ https://www.hovatek.com/forum/thread-15611.html

ReadPartition Finish

Message: Failed: Software has not supported this feature

Meaning: A backup setting is interfering with flashing

Solution:

• In Research Download, go to Settings > Options > Read Option and untick Read Partition

Bin packet version is not support

Message: Bin packet version is not support! Load bin packet failed!

Meaning: You’re either using an old version of the tool or an improperly built pac file
Solution:

• Try using the latest version of Research / Upgrade / Factory download tool
• Ensure you’re using a valid pac file

Просмотр полной версии : Supra M74AG окирпичил.Нужна помощь.