Ошибка sc202 ricoh 311

Thanks:  0

Dislikes:  0

1. 02-08-2018

   
   

   #1

   

   
   Junior Member
   

   

   ---

   Rep Power

   0

   SC202 of Ricoh SP320DN
   

   I posted this yesterday but in the wrong forum.. I read through the manual and still cannot see where the polygon mirror motor is located on the machine. or is there a way to reset this code. Inside the left cover all the other motors are working.

   Thanks

   Mike

   ---

2. 02-08-2018

   
   

   #2

   Re: SC202 of Ricoh SP320DN
   

   In most models it sets on top of the laser housing.

   ---

3. 02-09-2018

   
   

   #3

   Re: SC202 of Ricoh SP320DN
   

   Your Laser Housing is just below the Exit area and above the AIO. You will need to remove literally every external cover to access the Laser Housing and the Polygon Mirror Motor inside the Housing.

   ---

4. 02-09-2018

   
   

   #4

   Re: SC202 of Ricoh SP320DN
   

   Originally Posted by docsconsulting
   

   I posted this yesterday but in the wrong forum.. I read through the manual and still cannot see where the polygon mirror motor is located on the machine. or is there a way to reset this code. Inside the left cover all the other motors are working.

   Thanks

   Mike

   too bad you didnt post this last week i just gutted a working low meter one and left all the boards and laser as i only wanted the drums,fuser and ITB unit

   ---

5. 02-09-2018

   
   

   #5

   Re: SC202 of Ricoh SP320DN
   

   Originally Posted by docsconsulting
   

   I posted this yesterday but in the wrong forum.. I read through the manual and still cannot see where the polygon mirror motor is located on the machine. or is there a way to reset this code. Inside the left cover all the other motors are working.

   Thanks

   Mike

   In Service manual:
   Page 39: Laser unit
   Page 40: Polygon mirror motor

   ---

6. 02-12-2018

   
   

   #6

   

   
   Junior Member
   

   

   ---

   Rep Power

   0

   Re: SC202 of Ricoh SP320DN
   

   Originally Posted by fshead
   

   too bad you didnt post this last week i just gutted a working low meter one and left all the boards and laser as i only wanted the drums,fuser and ITB unit

   Do you still have the polygon motor?

   ---

7. 02-12-2018

   
   

   #7

   

   
   Junior Member
   

   

   ---

   Rep Power

   0

   Re: SC202 of Ricoh SP320DN
   

   Originally Posted by Gary Bowen
   

   Your Laser Housing is just below the Exit area and above the AIO. You will need to remove literally every external cover to access the Laser Housing and the Polygon Mirror Motor inside the Housing.

   Gary,

   Is it attached to the Exit cover? i see that under the cover…..will look again.

   Thanks

   Mike

   ---

8. 02-12-2018

   
   

   #8

   Re: SC202 of Ricoh SP320DN
   

   Originally Posted by docsconsulting
   

   Do you still have the polygon motor?

   no i tossed the boards and laser unit..
   if i am not mistaken on other machine a bad laser will smoke the board when it goes,so changing just
   the laser might not be the answer..
   i am in your neck of the woods..

   ---

9. 02-12-2018

   
   

   #9

   

   
   Junior Member
   

   

   ---

   Rep Power

   0

   Re: SC202 of Ricoh SP320DN
   

   Originally Posted by fshead
   

   no i tossed the boards and laser unit..
   if i am not mistaken on other machine a bad laser will smoke the board when it goes,so changing just
   the laser might not be the answer..
   i am in your neck of the woods..

   thanks,

   First it cam up with fuser needs replacement, then SC202….Either polygon mirror motor or bad board? Not sure if its worth fixing as the motors are not cheap

   ---

10. 02-12-2018

    
    

    #10

    Re: SC202 of Ricoh SP320DN
    

    Originally Posted by docsconsulting
    

    thanks,

    First it cam up with fuser needs replacement, then SC202….Either polygon mirror motor or bad board? Not sure if its worth fixing as the motors are not cheap

    SC 2xx (Laser Optics Error)
    202
    Polygon motor on timeout error
    The polygon mirror motor does not reach the targeted operating speed within
    1
    0
    sec.
    after turning
    after turning.
    
    Polygon motor/driver board harness loose or disconnected
    
    Polygon motor/driver
    board defective
    
    Laser optics unit defective
    1.
    Turn the machine main power off/on.
    2.
    Replace the interface harness of the laser optics unit.
    3.
    Replace the laser optics unit

    ---

Tags for this Thread