Ошибка p0949 форд куга

Найдена следующая информация по ошибке P0949 для автомобиля FORD KUGA (2008-2012), DR:

На русском языке:

Коробка передач с автоматизированным переключением (ASM) — не проведено адаптивное обучение

На английском языке:

Auto Shift Manual Adaptive Learning Not Complete

Вы можете задать вопрос или поделиться опытом устранения ошибки P0949 на автомобиле FORD с другими пользователями.

Возможную причину возникновения и советы по устранению можно найти в каталоге причин и советов:

Найти причину   >>> 

Ошибки (коды ошибок) полученные от прибора, сканера требуют правильной интерпретации информации, дабы не тратить время и деньги на замену работающих элементов автомобиля.

Проблема зачастую кроется намного глубже чем кажется на первый взгляд. Это& вызвано теми обстоятельствами, что информационные сообщения содержат, как было выше сказано, косвенную информацию о нарушении работы системы.

Может быть полезным для решения вопроса по устранению неисправности у Ford Kuga (DR):

ECM/PCM/TCM

ECM/PCM/TCM

P0603 EEPROM
fault INSTALL a new TCM P060A Internal Control Module, Monitoring Processor Performance INSTALL a new TCM P073E gear R engagement blocking (after internal handling) INSTALL a new transmission P073F gear 1 engagement blocking (after internal handling) INSTALL a new transmission P074A gear 2 engagement blocking (after internal handling) INSTALL a new transmission P074B gear 3 engagement blocking (after internal handling) INSTALL a new transmission P074C gear 4 engagement blocking (after internal handling) INSTALL a new transmission P074D gear 5 engagement blocking (after internal handling) INSTALL a new transmission P0791 In shaft 1 speed sensor defect, current out of range INSTALL a new TCM P0792 Input
shaft speed 1 defect INSTALL a new TCM P0847 Clutch 2 Pressure sensor voltage below normal operation voltage INSTALL a new TCM P0711 Hydraulic, hybrid temperature sensor plausibility failure INSTALL a new TCM P0715 Damper
speed sensor defect INSTALL a new TCM P0766 CSMS1 / CSM1 sticks low / low oil level CHECK for obvious oil leaks. CHECK the oil level and Test Drive. If symptoms persist INSTALL a new transmission P0771 CSMS2 / CSM2 sticks low / low oil level CHECK for obvious oil leaks. CHECK the oil level and Test Drive. If symptoms persist INSTALL a new transmission P0796 Clutch 1 Plausibility Failure pressure too low CHECK for obvious oil leaks. CHECK the oil level and Test Drive. If symptoms persist INSTALL a new transmission P2714 Clutch 2 Plausibility Failure pressure too low CHECK for obvious oil leaks. CHECK the oil level and Test Drive. If symptoms persist INSTALL a new transmission P2715 Clutch 2 Plausibility Failure pressure too high CHECK for obvious oil leaks. CHECK the oil level and Test Drive. If symptoms persist INSTALL a new transmission P0841 Clutch 1
Torque Plausibility Failure INSTALL a new Clutch, if symptoms persist INSTALL a new TCM P0846 Clutch 2
Torque Plausibility Failure INSTALL a new Clutch, if symptoms persist INSTALL a new TCM P2746 transmission path 2 speed plausibility error INSTALL a new TCM P1905 EOL Mode
active INSTALL a new TCM P0949 Teaching
not completed Check for the latest TCM software level, Run Teach in routine using the
Ford diagnostic equipment. P171A shift fork 1 requested but movement on shift fork 2 INSTALL a new TCM

If symptoms persist INSTALL a new transmission

P171C shift fork 2 requested but movement on shift fork 1 INSTALL a new TCM

If symptoms persist INSTALL a new transmission

P171D shift fork 2 requested but movement on shift fork 4 INSTALL a new TCM

If symptoms persist INSTALL a new transmission

P171F shift fork 3 requested but movement on shift fork 4 INSTALL a new TCM

If symptoms persist INSTALL

P172C shift fork ½ movement in opposite direction (to left cylinder) INSTALL a new TCM

If symptoms persist INSTALL a new transmission

P0581 SHSS1 current driver error: Short to Battery INSTALL a new TCM P0798 CSPS1 valve current driver error: overcurrent INSTALL a new TCM P2716/9 CSPS2 valve current driver error: overcurrent INSTALL a new TCM P2720 CSPS2 valve current error: Short to Ground INSTALL a new TCM P0964 CCFS current driver error Open load INSTALL a new TCM P0979 SHCMS current driver error: Short to Ground INSTALL a new TCM P0753 SHSS1 current driver error: Open load INSTALL a new TCM P0778 CCFS current driver error: overcurrent INSTALL a new TCM P0657 Common high side driver 1 not functional INSTALL a new TCM P092C Shift lock output short to Ground / Open Load CHECK wiring for continuity, if symptoms persist INSTALL a new TCM P081B Start lock output error: Short to Battery CHECK wiring for short, if symptoms persist INSTALL a new TCM P283B shift fork position 3 position range error (in counts) INSTALL a new TCM P283D shift fork position sensor 3 low output voltage failure INSTALL a new TCM P2840 shift fork position 4 position range error (in counts) INSTALL a new TCM P2842 shift fork position sensor 4 low output voltage failure INSTALL a new TCM P2846 shift fork position sensor 2 neutral plausibility error INSTALL a new TCM P2849 shift fork 1 blocked completely and no unexpected movement on other shift
fork INSTALL a new transmission P284A shift fork 2 blocked completely and no unexpected movement on other shift
fork INSTALL a new transmission P284B shift fork 3 blocked completely and no unexpected movement on other shift
fork INSTALL a new transmission P284C shift fork 4 blocked completely and no unexpected movement on other shift
fork INSTALL a new transmission P284D shift fork 1 movement but not requested INSTALL a new TCM P284F shift fork 3 movement but not requested INSTALL a new TCM P2850 shift fork 4 movement but not requested INSTALL a new TCM P0733 shift fork 2 jump out from forward towards the engine (left side) INSTALL a new TCM

If symptoms persist INSTALL

P0734 shift fork 3 jump out from rearward towards the engine (right side) INSTALL a new TCM

If symptoms persist INSTALL a new transmission