product
DISPLAY
«E04»
Control board overheating
«E05»
Shortening overheating
«E06»
Temperature probe failure
«E41»
Programming Failure
«E71»
Pump motor relay failure or
wiring problem
1103
In the event of a control system failure, the digital display
shows an error message. These messages are coded: «E04»,
«E05», «E06», «E41». A constant tone is heard when an error
code is displayed, and to silence this tone, press any of the
CAUSE
buttons.
PANEL BOARD CORRECTION
Turn switch to OFF position, then turn
switch back to ON; if display still shows
«E04», the board is getting too hot; check
for signs of overheating behind the control
panel; once panel cools down the controls
should return to normal; if «E04» persists,
replace the control
Turn switch to OFF position, then back to
ON; if display shows «E05», the heating
circuits and temperature probe should be
checked; once the unit cools down, the
controls should return to normal; if «E05»
persists, replace the controls
Turn switch to OFF position, then back to
ON; if the display shows «E06», the tem-
perature probe should be checked; once the
temperature probe is repaired, or replaced,
controls should return to normal; if «E06»
persists, replace the controls
Turn switch to OFF position, then back to
ON. If display shows «E41», the control
should be re-initialized (see programming
section); if the error code persists, replace
the control panel.
Replace relay if contacts are stuck closed;
check wiring on POWER/PUMP switch, or
wall receptacle; L1 and N may be reversed
Model 590/592
1-11
Model EEE-141,142, 143, 144
7-2. ERROR CODES
In the event of a control system failure, the digital display shows an
error message. The message codes are shown in the DISPLAY
column below. A constant tone is heard when an error code is
displayed, and to silence this tone, press any button.
DISPLAY
CAUSE
CORRECTION
“E-4”
Control board
Turn switch to OFF position, then turn switch back to ON;
overheating
if display shows “E-4”, the control board is getting too hot;
check the louvers on each side of the unit for obstructions
“E-5”
Oil
Turn switch to OFF position, then turn switch back to ON;
overheating
if display shows “E-5”, the heating circuits and temperature
probes should be checked
“E-6A”
Temperature
Turn switch to OFF position, then turn switch back to ON;
probe open
if display shows “E-6A”, the temperature probe should be
checked
“E-6B”
Temperature
Turn switch to OFF position, then turn switch back to ON;
probe shorted
if display shows “E-6B”, the temperature probe should be
checked
“E-10”
High limit
Reset the high limit by using a small screwdriver or Allen
wrench gently pushing it into the hole in the heating element
hinge; if high limit does not reset, high limit may need be replaced
“E-15”
Drain switch
Make sure drain knob is completely pushed-in; if E-15 persists,
have drain switch checked
“E-18-A”
Left level sensor open
Turn switch to OFF position, then turn switch back to ON;
“E-18-B”
Right level sensor open
if display still indicates a failed sensor, have the connectors checked
“E-18-C”
Both level sensors open at the control board; have sensor checked & replace if necessory
209
7-3
-
Доброго дня коллеги. Имеется на обслуге фритюрница Henny Penny Computron 8000. Так вот. Жарка происходит под давлением, после окончания жарки должен происходить сброс давления паров через соленоид (по словам поваров). Этого не происходит. Сброс пара осуществляют методом «Хорошо ударить по корпусу соленоида». Подскажите в какую сторону копать и если можно эл. схему на данный девайс. Копать по проводам не дают, долго, а фритюрница постоянно в работе
-
Куда ударяют и работает,там и проблема. Попробуйте разобрать.
-
Ударяют просто сверху по корпусу соленоида и катушка. Нет питания на катушку, почему схему прошу чтоб понять при каком условии и откуда должно податься питание на катушку соленоида
-
В любом случае надо разобрать, чтобы найти плату управления, раз от удара работает-значит плохой контакт где то
-
блин да я это все прекрасно понимаю. Я ж написал что долго ковыряться не дадут. А без схемы это все будет тыканием слепого котенка
-
Ознакомьтесь с инструкцией, может поможет.
Вложения:
-
За документацию огромное спасибо. Даа от схемы я большего конечно ждал. Ну с помощью инструкции думаю осилю
Поделиться этой страницей
Model HHC-990
303
4-7
5-2. ERROR CODES AND
The display shows the following error codes and warnings when a
WARNINGS
fault is detected, along with an alarm sound. Both the heat and
humidity systems shut down, except when specified otherwise.
Display
Cause
Panel Board Correction
“E-4
CPU TOO HOT”
• Control board too hot;
unit overheating or
louvers clogged
“E-5
AIR TEMP TOO HOT”
• Faulty relay, PC board,
or air probe
“E-54A CPU TEMP SENSOR
• Faulty PC board
OPEN”
“E-54B CPU TEMP SENSOR
• Faulty PC board
SHORTED”
“E-6A
AIR TEMP SENSOR
• Faulty air probe
FAILED OPEN”
• Turn switch to OFF position, then back to
ON; if display still shows “E-4”, the PC
board is getting too hot; clean louvers and
check cooling fan; if cooling fan is not
working, have it replaced; once panel
cools down, the controls should return to
normal; if “E-4” persists, have the PC
board replaced
• Turn switch to OFF position, then back to
ON; if display shows “E-5”, the heating
circuits and temperature probe should be
checked; once the unit cools down, the
controls should return to normal; if “E-5”
persists, have the PC board replaced
• Turn switch to OFF position, then back to
ON; if display shows “E-54A”, the
control should be re-initialized (see Pro-
gramming Section); if the error code
persists, have PC board replaced
• Turn switch to OFF position, then back to
ON; if display shows “E-54B”, the
control should be re-initialized (see Pro-
gramming Section); if the error code
persists, have PC board replaced
• Turn switch to OFF position, then back to
ON; if the display shows “E-6”, the
temperature probe should be checked;
once the temperature probe is repaired, or
replaced, the controls should return to
normal; if “E-6” persists, have the PC
board replaced