Ошибка cf010 kyocera m2035dn

Модератор: vetal

---

---

---

---

---

---

---

---

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 101

Сообщения без ответов | Активные темы

Код ошибки Описание ошибки Причина ошибки 0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem. Defective FAX control PWB. 0070 FAX control PWB incompatible detection Error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. Defective fax software. Defective FAX control PWB. 0100 Backup memory device error Defective flash memory. Defective control PWB. Defective flash memory. Defective control PWB. 0120 MAC address data error Defective flash memory. 0130 Backup memory read/write error Defective flash memory. Defective control PWB 0140 Backup memory data error Defective flash memory. Defective control PWB. 0150 Control PWB EEPROM error
Detecting control PWB EEPROM (U17) communication error. Improper installation control PWB EEPROM (U17). Defective control PWB. 0170 Billing counting error Defective control PWB. Data damage of control PWB EEPROM (U17). 0180 Machine number mismatch
Machine number of main and engine does not match. The main PWB or the engine PWB were exchanged. Data damage of control PWB EEPROM (U17). 0420 Paper feeder communication error
Communication error between control PWB and optional paper feeder. Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF mainPWB. 0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB. Defective fax software. Defective FAX control PWB. 0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. Defective control PWB. The battery is disconnected from the control PWB. 0870 FAX control PWB to control PWB high capacity data transfer problem
High-capacity data transfer between the FAX control PWB and the control PWB of the machine was not normally performed even if the data transfer was retried the specified times. Improper installation FAX control PWB. Defective FAX control PWB or control PWB. 0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. Defective FAX control PWB. 2000 Main motor error
The main motor ready input is not given for 2 s during the main motor is ON. Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Defective drive transmission system of the main motor. Defective main motor. Defective control PWB. 2610 PF paper feed motor error (paper feeder)
The PF paper feed motor of cassette 2 ready input is not given for 2 s during the PF paper feed motor is ON. Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB. 2620 PF paper feed motor error (Paper feeder)
The PF paper feed motor of cassette 3 ready input is not given for 2 s during the PF paper feed motor is ON. Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB. 3100 ISU home position errorr. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion. Defective home position sensor. Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion. Defective ISU motor. 3200 Exposure lamp error
The exposure lamp is not turned on. Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Defective exposure lamp.sensor. Defective LED drive PWB. Defective control PWB. 3300 AGC error
After AGC, correct input is not obtained at CCD. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective exposure lamp.sensor. Defective CCD PWB. Defective control PWB. 3500 CPU — ASIC (CCD PWB) communication error
An error code is detected. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective CCD PWB. Defective control PWB. 4000 Polygon motor (laser scanner unit) error
The polygon motor ready input is not given for 6 s during the polygon motor is ON. Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB. 4200 BD error (laser scanner unit) error. BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB. 4700 VIDEO ASIC device error
Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector. Defective control PWB. 6000 Broken Fuser heater wire
The fuser temperature does not rise after the Fuser heater has been turned on. Poor contact in the fuser thermistor connector terminals. Poor contact in the Fuser heater connector terminals. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater installed incorrectly. Broken Fuser heater wire. 6020 Abnormally high fuser thermistor temperature
Fuser thermistor detects abnormally temperature. When the temperature of a fuser thermistor detects 195 °C or more at the time of heater OFF and 155 °C or more. Shorted fuser thermistor. Defective control PWB. 6030 Broken fuser thermistor wire
Input from fuser thermistor is 0 (A/D value). Poor contact in the fuser thermistor connector terminals. Broken fuser thermistor wire. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater installed incorrectly. Broken Fuser heater wire. 6400 Zero cross signal error
The zero cross signal does not reach the control PWB for specified time. Defective harness between high voltage PWB (CN202) and control PWB (YC23), or improper connector insertion. Defective connection between power source PWB (YC103) and high voltage PWB (CN201). Defective power source PWB. Defective control PWB. 7990 Waste toner full
The waste toner sensor has detected that the waste toner reservoir (drum unit) is full. Waste toner reservoir (drum unit) is full. Defective waste toner sensor. Defective control PWB. F000 Control PWB — Operation panel PWB communication error Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion. motor is ON. Defective operation panel PWB. Defective control PWB. F020 Control PWB RAM checksum error Defective main memory (RAM) on the control PWB. Defective expanded memory (DIMM). F040 Control PWB engine communication error
A communication error is detected. Defective control PWB. F041 Control PWB — scanner PWB communication error
A communication error is detected. Defective control PWB or scanner PWB. F050 Control PWB engine checksum error Some error may have occurred when downloading the firmware of the control PWB. Defective control PWB. F186 Control PWB video data control error Defective control PWB.

Если с аппаратом Kyocera TASKalfa 1800, Kyocera TASKalfa 2200 произошла проблема, откроется следующий экран с уведомлением.
• Индикатор [Внимание] на панели управления горит или мигает.
• На дисплее сообщений панели управления аппарата появилось сообщение об ошибке.

Если индикатор [Внимание] горит или мигает и на дисплее сообщений панели управления аппарата появилось сообщение об ошибке, проверьте KYOCERA Client Tool или Монитор состояния.

ПРИМЕЧАНИЕ Если индикаторы постоянно горят и мигают не так, как описано выше, вероятно, произошла ошибка службы. Выключите питание, отсоедините шнур питания и вставьте его обратно, после чего включите питание. Это может помочь сбросить ошибку. Если ошибка не исчезает, свяжитесь со своим представителем сервисной службы (тел. в Минске +375 17 291-28-24)

Ниже описаны неполадки, которые не могут быть устранены пользователем