Micro motion 2700 ошибки

Contents
Table of Contents
Troubleshooting
Bookmarks

Related Manuals for Emerson Micro Motion 2700

Summary of Contents for Emerson Micro Motion 2700

Page 1
Configuration and Use Manual 20000326, Rev ED April 2018 ® Micro Motion Model 2700 Transmitters with ™ FOUNDATION Fieldbus Configuration and Use Manual…
Page 2
Micro Motion employees. Micro Motion will not accept your returned equipment if you fail to follow Micro Motion procedures. Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion Customer Service department.
Page 3: Table Of Contents

Contents Contents Part I Getting started Chapter 1 Before you begin ………………….3 About this manual ……………………3 Communication methods ………………….3 Additional documentation and resources ………………4 Chapter 2 Quick start ……………………5 Power up the transmitter ………………….5 Check meter status ……………………5 2.2.1 Transmitter status reported by LED …………….6 Determine the FOUNDATION Fieldbus unique device ID …………..7…
Page 4
Contents 4.5.2 Configure two-phase flow parameters ……………. 34 4.5.3 Configure Density Damping ………………35 4.5.4 Configure Density Cutoff ………………..36 Configure temperature measurement ………………37 4.6.1 Configure Temperature Measurement Unit …………..37 4.6.2 Configure Temperature Damping …………….38 4.6.3 Effect of Temperature Damping on process measurement ……… 39 Configure the petroleum measurement application …………..
Page 5
Contents Back up transmitter configuration ………………… 71 Return function blocks to In Service (Auto) mode …………..72 Part III Operations, maintenance, and troubleshooting Chapter 7 Transmitter operation ………………..75 Record the process variables ………………… 75 View process variables …………………..76 7.2.1 View process variables using the display …………..76 7.2.2 View process variables and other data using ProLink III ……….77…
Page 6
Contents Check the drive gain …………………… 122 9.9.1 Collect drive gain data ………………..123 9.10 Check the pickoff voltage ………………….123 9.10.1 Collect pickoff voltage data ………………124 9.11 Check for internal electrical problems ………………124 9.11.1 Check the sensor coils ………………..124 Appendices and reference Appendix A Transducer blocks and views ………………127…
Page 7
Contents A.8.3 Process variables for concentration measurement transducer blocks ……. 225 A.8.4 Totals for concentration measurement transducer blocks ……..226 A.8.5 Setup data for concentration measurement transducer blocks ……… 227 A.8.6 Other additions for concentration measurement transducer blocks ……232 Density viscosity meter transducer blocks …………….
Page 8
Contents Appendix D Using the transmitter display ………………299 Using the display ……………………299 D.1.1 Components of the transmitter interface …………..299 D.1.2 Use the optical switches ………………..300 D.1.3 Access and use the display menu system …………..300 D.1.4 Display codes for process variables …………….305 D.1.5 Codes and abbreviations used in display menus …………306 Appendix E…
Page 9: Getting Started

Getting started Part I Getting started Chapters covered in this part: • Before you begin • Quick start Configuration and Use Manual…
Page 10
Getting started Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 11: Before You Begin

Before you begin Before you begin Topics covered in this chapter: • About this manual • Communication methods • Additional documentation and resources About this manual This manual helps you configure, commission, use, maintain, and troubleshoot ™ Micro Motion Model 2700 transmitters with FOUNDATION fieldbus.
Page 12: Additional Documentation And Resources

Topic Document Hazardous area installa- See the approval documentation shipped with the transmitter, or tion download the appropriate documentation at www.emerson.com. ™ Product Data Sheet Micro Motion Series 1000 and Series 2000 Transmitters with MVD Tech‐ nology Product Data Sheet…
Page 13: Chapter 2 Quick Start

Quick start Quick start Topics covered in this chapter: • Power up the transmitter • Check meter status • Determine the FOUNDATION Fieldbus unique device ID • Make a startup connection to the transmitter • Verify mass flow measurement Power up the transmitter The transmitter must be powered up for all configuration and commissioning tasks, or for process measurement.
Page 14: Transmitter Status Reported By Led

Quick start Wait approximately 10 seconds for the power-up sequence to complete. Immediately after power-up, the transmitter runs through diagnostic routines and checks for error conditions. During the power-up sequence, Alert A009 is active. This alert should clear automatically when the power-up sequence is complete. Check the status LED on the transmitter.
Page 15: Determine The Foundation Fieldbus Unique Device Id

Quick start Determine the FOUNDATION Fieldbus unique device ID The transmitter is shipped with a sticker that displays a unique 32-digit number that the fieldbus segment uses for identification. If the sticker is missing, use this procedure to determine your device ID. From ProLink III, navigate to Device Tools >…
Page 16
Quick start Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 17: Part Ii Configuration And Commissioning

Configuration and commissioning Part II Configuration and commissioning Chapters covered in this part: • Introduction to configuration and commissioning • Configure process measurement • Configure device options and preferences • Complete the configuration Configuration and Use Manual…
Page 18
Configuration and commissioning Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 19: Introduction To Configuration And Commissioning

Introduction to configuration and commissioning Introduction to configuration and commissioning Topics covered in this chapter: • Configuration flowchart • Default values and ranges • Enable access to the off‐line menu of the display • Disable write‐protection on the transmitter configuration •…
Page 20
Introduction to configuration and commissioning Figure 3-1: Configuration flowchart Configure device options and preferences Test and move to production Configure process measurement Configure mass flow Test or tune transmitter Configure display measurement using sensor simulation parameters Configure volume flow meaurement Configure fault handling Back up transmitter parameters…
Page 21: Default Values And Ranges

Introduction to configuration and commissioning Default values and ranges Section G.1 to view the default values and ranges for the most commonly used parameters. Enable access to the off-line menu of the display Display OFF-LINE MAINT > OFF-LINE CONFG ProLink III Device Tools >…
Page 22: Place Function, Transducer, And Resource Blocks In Oos Mode

Introduction to configuration and commissioning Place function, transducer, and resource blocks in OOS mode Before you modify parameters on the fieldbus function, transducer, and resource blocks, you must place the blocks in Out of Service (OOS) mode. Before you return the device to operation, you must place them back in service (Auto mode).
Page 23: Restore The Factory Configuration

Introduction to configuration and commissioning Restore the factory configuration Display Not available ProLink III Device Tools > Configuration Transfer > Restore Factory Configuration Field Communicator Service Tools > Maintenance > Reset/Restore > Master Reset Fieldbus host Diagnostic TB > Restore Factory Config (OD Index 056) Overview Restoring the factory configuration returns the transmitter to a known operational configuration.
Page 24
Introduction to configuration and commissioning Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 25: Configure Process Measurement

Configure process measurement Configure process measurement Topics covered in this chapter: • Configure mass flow measurement • Configure volume flow measurement for liquid applications • Configure GSV flow measurement • Configure flow direction • Configure density measurement • Configure temperature measurement •…
Page 26
Configure process measurement Options for Mass Flow Measurement Unit The transmitter provides a standard set of measurement units for Mass Flow Measurement Unit, plus one user-defined special measurement unit. Different communications tools may use different labels for the units. Label Display ProLink III Field Communica-…
Page 27
Configure process measurement Define a special measurement unit for mass flow Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Special Units > Mass Special Units Fieldbus host Measurement TB >…
Page 28: Configure Flow Damping

Configure process measurement Example: Defining a special measurement unit for mass flow You want to measure mass flow in ounces per second (oz/sec). Set Base Mass Unit to Pounds (lb). Set Base Time Unit to Seconds (sec). Calculate Mass Flow Conversion Factor: a.
Page 29: Configure Mass Flow Cutoff

Configure process measurement • In general, lower damping values are preferable because there is less chance of data loss, and less lag time between the actual measurement and the reported value. The value you enter is automatically rounded off to the nearest valid value. For example, if the damping is currently set to 0.8 seconds, any value entered up to 1.2 seconds will be rounded down to 0.8 seconds, and any value entered from 1.21 to 1.59 seconds will be rounded up to 1.6 seconds.
Page 30: Configure Volume Flow Measurement For Liquid Applications

Configure process measurement Configure volume flow measurement for liquid applications The volume flow measurement parameters control how liquid volume flow is measured and reported. Restriction You cannot implement both liquid volume flow and gas standard volume flow at the same time. Choose one or the other.
Page 31
Configure process measurement Overview Volume Flow Measurement Unit specifies the unit of measurement that will be displayed for the volume flow rate. The unit used for the volume total and volume inventory is based on this unit. Prerequisites Before you configure Volume Flow Measurement Unit, be sure that Volume Flow Type is set to Liquid.
Page 32
Configure process measurement Label Unit description Display ProLink III Field Communicator l/hr Liters per hour Million liters per day MILL/D mil l/day ML/d UKGPS Imp gal/sec Impgal/s Imperial gallons per second UKGPM Imp gal/min Impgal/min Imperial gallons per minute UKGPH Imp gal/hr Impgal/h Imperial gallons per hour…
Page 33: Configure Volume Flow Cutoff

Configure process measurement The special unit label displays only on the local display. The AI block uses and displays the actual engineering unit (i.e. L/min). Procedure Specify Base Volume Unit. Base Volume Unit is the existing volume unit that the special unit will be based on. Specify Base Time Unit.
Page 34: Configure Gsv Flow Measurement

Configure process measurement Overview Volume Flow Cutoff specifies the lowest volume flow rate that will be reported as measured. All volume flow rates below this cutoff are reported as 0. Procedure Set Volume Flow Cutoff to the value you want to use. The default value for Volume Flow Cutoff is 0.0 l/sec (liters per second).
Page 35: Configure Standard Density Of Gas

Configure process measurement Procedure Set Volume Flow Type to Gas Standard Volume. 4.3.2 Configure Standard Density of Gas Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure > Manual Setup > Measurements > GSV > Gas Ref Density Fielbus host Measurement TB >…
Page 36
Configure process measurement The default setting for Gas Standard Volume Flow Unit is SCFM (Standard Cubic Feet per Minute). If the measurement unit you want to use is not available, you can define a special measurement unit. Options for Gas Standard Volume Flow Unit The transmitter provides a standard set of measurement units for Gas Standard Volume Flow Unit, plus one user-defined special measurement unit.
Page 37
Configure process measurement Define a special measurement unit for gas standard volume flow Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Special Units > Special GSV Units Fieldbus host Measurement TB >…
Page 38: Configure Gas Standard Volume Flow Cutoff

Configure process measurement The special measurement unit is stored in the transmitter. You can configure the transmitter to use the special measurement unit at any time. Example: Defining a special measurement unit for gas standard volume flow You want to measure gas standard volume flow in thousands of standard cubic feet per minute.
Page 39: Configure Flow Direction

Configure process measurement Configure flow direction Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure > Manual Setup > Measurements > Flow > Flow Direction Fieldbus host Measurement TB > FLOW_DIRECTION {OD Index 41) Overview Flow Direction controls how forward flow and reverse flow affect flow measurement and reporting.
Page 40
Configure process measurement Flow Direction setting Relationship to Flow Direction arrow ProLink III Field Communicator on sensor Negate Forward Negate/Forward Only Appropriate when the Flow Direction ar- row is in the opposite direction from the majority of flow. Negate Bidirectional Negate/Bi-directional Appropriate when both forward and re- verse flow are expected, and reverse flow…
Page 41: Configure Density Measurement

Configure process measurement Configure density measurement The density measurement parameters control how density is measured and reported. 4.5.1 Configure Density Measurement Unit Display OFF-LINE MAINT > OFF-LINE CONFG > UNITS > DENS ProLink III Device Tools > Configuration > Process Measurement > Density Field Communicator Configure >…
Page 42: Configure Two-Phase Flow Parameters

Configure process measurement Label Unit description Display ProLink III Field Communicator D API degAPI degAPI Degrees API (1) Non‐standard calculation. This value represents line density divided by the density of water at 4 °C. 4.5.2 Configure two-phase flow parameters Display Not available ProLink III Device Tools >…
Page 43: Configure Density Damping

Configure process measurement You must enter Two-Phase Flow High Limit in g/cm³, even if you configured another unit for density measurement. Set Two-Phase Flow Timeout to the number of seconds that the transmitter will wait for a two-phase flow condition to clear before posting the alert. The default value for Two-Phase Flow Timeout is 0.0 seconds, meaning that the alert will be posted immediately.
Page 44: Configure Density Cutoff

Configure process measurement Damping is used to smooth out small, rapid fluctuations in process measurement. Damping Value specifies the time period (in seconds) over which the transmitter will spread changes in the process variable. At the end of the interval, the internal value will reflect 63% of the change in the actual measured value.
Page 45: Configure Temperature Measurement

Configure process measurement Overview Density Cutoff specifies the lowest density value that will be reported as measured. All density values below this cutoff will be reported as 0. Procedure Set Density Cutoff to the value you want to use. For most applications, the default setting (0.2 g/cm³) is sufficient. The range is 0.0 g/cm³ to 0.5 g/cm³.
Page 46: Configure Temperature Damping

Configure process measurement Label Field Communica- Unit description Display ProLink III °C °C degC Degrees Celsius Degrees Fahrenheit °F °F degF °R °R degR Degrees Rankine °K °K Kelvin 4.6.2 Configure Temperature Damping Display Not available ProLink III Device Tools > Configuration > Temperature Field Communicator Configure >…
Page 47: Effect Of Temperature Damping On Process Measurement

Configure process measurement • In general, lower damping values are preferable because there is less chance of data loss, and less lag time between the actual measurement and the reported value. The value you enter is automatically rounded off to the nearest valid value. Valid values for Temperature Damping are 0, 0.6, 1.2, 2.4, 4.8, ……
Page 48
Configure process measurement Prerequisites You will need API documentation for the API table that you select. Depending on your API table, you may need to know the thermal expansion coefficient (TEC) for your process fluid. You must know the reference temperature that you want to use. Procedure Choose Device Tools >…
Page 49: Configure Petroleum Measurement Using The Field Communicator

Configure process measurement b. Verify that the referred density range of the selected table is adequate for your application. If you chose a C table, enter Thermal Expansion Coefficient (TEC) for your process fluid. Set Reference Temperature to the temperature to which density will be corrected in referred density calculations.
Page 50
Configure process measurement Table name Process fluid CTL source data Reference temperature Density unit Generalized crude and Observed density and 60 °F (non-configurable) Degrees API observed temperature Range: 0 to 100 Generalized products Observed density and 60 °F (non-configurable) Degrees API observed temperature Range: 0 to 85 Lubricating oils…
Page 51: Set Up Concentration Measurement

Configure process measurement Set up concentration measurement This section guides you through loading and setting up a concentration matrix used for measurement. It does not cover building a concentration matrix. The concentration measurement application calculates concentration data from process temperature and density. Micro Motion provides a set of concentration matrices that provide the reference data for several standard industry applications and process fluids.
Page 52: Configure Concentration Measurement Using The Field Communicator

Configure process measurement • If you change the setting of Derived Variable, all existing concentration matrices will be deleted from transmitter memory. Set Derived Variable before loading concentration matrices. Load one or more matrices. a. Set Matrix Being Configured to the location to which the matrix will be loaded. b.
Page 53
Configure process measurement Choose Online > Configure > Manual Setup > Measurements > Temperature and set Temperature Unit to match the temperature unit used by your matrix. Choose Online > Configure > Manual Setup > Measurements and click Concentration Measurement. Set up extrapolation alerts.
Page 54: Standard Matrices For The Concentration Measurement Application

Configure process measurement Option Setup A value written by a. Choose Online > Configure > Manual Setup > Measurements > digital communica- External Inputs tions b. Enable External Temperature. c. Perform the necessary host programming and communications setup to write temperature data to the transmitter at appropri- ate intervals.
Page 55: Derived Variables And Calculated Process Variables

Configure process measurement Temperature Matrix name Description Density unit unit Derived variable HFCS 42 °C Mass Concentration Matrix represents a hydrometer scale g/cm (Density) for HFCS 42 (high-fructose corn syrup) solutions that indicates the percent by mass of HFCS in solution. HFCS 55 Matrix represents a hydrometer scale g/cm…
Page 56: Set Up Concentration Measurement Using A Basic Ff Host

Configure process measurement Calculated process variables Density at reference Standard Derived tempera- volume Specific Concen- Net mass volume Variable Description ture flow rate gravity tration flow rate flow rate ✓ ✓ ✓ ✓ ✓ Mass The percent mass of Concentration solute or of material in (Specific Gravity) suspension in the total…
Page 57: Set Reference Temperature Values For Specific Gravity Using A Basic Ff Host

Configure process measurement 4.9.1 Set reference temperature values for specific gravity using a basic FF host When Derived Variable is set to any option based on specific gravity, you must set the reference temperature for water, then verify the density of water at the configured reference temperature.
Page 58: Modify Extrapolation Alerts For Concentration Measurement Using A Basic Ff Host

Configure process measurement Table 4-3: Concentration unit codes Fieldbus code Unit 1110 degTwad 1426 degBrix 1111 degBaum hv 1112 degBaum It 1343 % sol/wt 1344 % sol/vol 1427 degBall 1428 proof/vol 1429 proof/mass 1346 % plato special Write a value into the Special Concentration Unit Label parameter if Concentration Unit is set to code 253 (special).
Page 59: Select The Active Concentration Matrix Using A Basic Ff Host

Not all sensors or applications require pressure compensation. The pressure effect for a specific sensor model can be found in the product data sheet located at www.emerson.com. If you are uncertain about implementing pressure compensation, contact customer service. Prerequisites You will need the flow factor, density factor, and calibration pressure values for your sensor.
Page 60: Configure Pressure Compensation Using Prolink Iii

Configure process measurement • For the calibration pressure, see the calibration sheet for your sensor. If the data is unavailable, use 20 PSI. 4.10.1 Configure pressure compensation using ProLink III Choose Device Tools > Configuration > Process Measurement > Pressure Compensation.
Page 61: Options For Pressure Measurement Unit

Configure process measurement The flow factor is the percent change in the flow rate per PSI. When entering the value, reverse the sign. Example: If the flow factor is 0.000004 % per PSI, enter −0.000004 % per PSI. Enter Dens Press Factor for your sensor. The density factor is the change in fluid density, in g/cm /PSI.
Page 62
Configure process measurement Label Unit description Display ProLink III Field Communicator mmH2O mm Water @ 68°F mmH2O (68°F) Millimeters water @ 68 °F Millimeters mercury @ 0 °C mmHG mm Mercury @ 0°C mmHg (0°C) INHG In Mercury @ 0°C inHg (0°C) Inches mercury @ 0 °C Pounds per square inch…
Page 63: Configure Device Options And Preferences

Configure device options and preferences Configure device options and preferences Topics covered in this chapter: • Configure the transmitter display • Enable or disable operator actions from the display • Configure security for the display menus • Configure response time parameters •…
Page 64: Configure The Process Variables And Diagnostic Variables Shown On The Display

Configure device options and preferences 5.1.2 Configure the process variables and diagnostic variables shown on the display Display Not available ProLink III Device Tools > Configuration > Transmitter Display > Display Variables Field Communicator Configure > Manual Setup > Display > Display Variables Fieldbus host LDO TB >…
Page 65: Configure The Number Of Decimal Places (Precision) Shown On The Display

Configure device options and preferences Display variable Process variable assignment Display Variable 12 None Display Variable 13 None Display Variable 14 None Display Variable 15 None 5.1.3 Configure the number of decimal places (precision) shown on the display Display Not available ProLink III Device Tools >…
Page 66: Configure The Refresh Rate Of Data Shown On The Display

Configure device options and preferences 5.1.4 Configure the refresh rate of data shown on the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > RATE ProLink III Device Tools > Configuration > Transmitter Display > Display Variables Field Communicator Configure > Manual Setup > Display > Display Variable Menu Features > Refresh Rate Fieldbus host LDO TB >…
Page 67: Enable Or Disable The Display Backlight

Configure device options and preferences If you enabled Auto Scroll, set Scroll Rate as desired. The default value is 10 seconds. Scroll Rate may not be available until you apply Auto Scroll. 5.1.6 Enable or disable the display backlight Display OFF-LINE MAINT >…
Page 68: Enable Or Disable Operator Actions From The Display

Configure device options and preferences Enable or disable operator actions from the display You can configure the transmitter to let the operator perform specific actions using the display. • Enable or disable Totalizer Start/Stop from the display (Section 5.2.1) • Enable or disable Totalizer Reset from the display (Section 5.2.2) •…
Page 69: Enable Or Disable Totalizer Reset From The Display

Configure device options and preferences 5.2.2 Enable or disable Totalizer Reset from the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > TOTALS RESET ProLink III Device Tools > Configuration > Totalizer Control Methods Field Communicator Configure > Manual Setup > Display > Display Variable Menu Features > Totalizer Reset Fieldbus host LDO TB >…
Page 70: Configure Security For The Display Menus

Configure device options and preferences Overview You can configure whether or not the operator can use a single command to acknowledge all alerts from the display. Procedure Ensure that the alert menu is accessible from the display. To acknowledge alerts from the display, operators must have access to the alert menu.
Page 71
Configure device options and preferences Option Description Enabled (default) Operator can access the alert menu. This access is required to view and acknowledge alerts, but is not required for Smart Meter Verification (if applicable), configuration, or calibration. Disabled Operator cannot access the alert menu. Note The transmitter status LED changes color to indicate that there are active alerts, but does not show specific alerts.
Page 72: Configure Response Time Parameters

Configure device options and preferences Configure response time parameters You can configure the rate at which process data is polled and process variables are calculated. Configure alert handling The alert handling parameters control the transmitter’s response to process and device conditions.
Page 73: Configure Status Alert Severity

Configure device options and preferences 5.5.2 Configure Status Alert Severity Display Not available ProLink III Device Tools > Configuration > Alert Severity Field Communicator Configure > Alert Setup > Alert Severity > Set Alert Severity Fieldbus host Diag TB > ALARM_INDEX (OD Index 23) Diag TB >…
Page 74
Configure device options and preferences Status alerts and options for Status Alert Severity Table 5-1: Status alerts and Status Alert Severity Alert code Status message Default severity Notes Configurable? A001 EEPROM Error (Core Pro- Fault cessor) RAM Error (Core Processor) Fault A002 Fault A003…
Page 75: Configure Informational Parameters

Configure device options and preferences Table 5-1: Status alerts and Status Alert Severity (continued) Alert code Status message Default severity Notes Configurable? Meter Verification Aborted Fault A035 Applies only to transmitters with Smart Meter Verification. A102 Drive Overrange Informational A104 Calibration in Progress Informational Can be set to either Informational or…
Page 76: Configure Sensor Serial Number

Configure device options and preferences 5.6.1 Configure Sensor Serial Number Display Not available ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information > Sensor Serial Num- Fieldbus host Device Info TB >…
Page 77: Configure Sensor Liner Material

Configure device options and preferences 5.6.3 Configure Sensor Liner Material Display Not available ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information > Tube Lining Fieldbus host Device Info TB >…
Page 78: Configure Descriptor

Configure device options and preferences 5.6.5 Configure Descriptor Display Not available ProLink III Device Tools > Configuration > Informational Parameters > Transmitter Field Communicator Configure > Manual Setup > Info Parameters > Transmitter Info > Descriptor Fieldbus host Device Info TB > DESCRIPTION (OD Index 19) Overview Descriptor lets you store a description in transmitter memory.
Page 79: Complete The Configuration

Complete the configuration Complete the configuration Topics covered in this chapter: • Back up transmitter configuration • Return function blocks to In Service (Auto) mode Back up transmitter configuration ProLink III provides a configuration upload/download function which allows you to save configuration sets to your PC.
Page 80: Return Function Blocks To In Service (Auto) Mode

Complete the configuration Return function blocks to In Service (Auto) mode Display Not available ProLink III Not available Field Communicator Overview > Mode Fieldbus host All TBs > MODE_BLOCK (OD Index Number 005) Overview After modifying function block parameters, the fieldbus function blocks must be placed in service (Auto) mode before you return the device to operation.
Page 81: Part Iii Operations, Maintenance, And Troubleshooting

Operations, maintenance, and troubleshooting Part III Operations, maintenance, and troubleshooting Chapters covered in this part: • Transmitter operation • Measurement support • Troubleshooting Configuration and Use Manual…
Page 82
Operations, maintenance, and troubleshooting Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 83: Chapter 7 Transmitter Operation

Reset inventories Record the process variables Emerson suggests that you make a record of specific process variable measurements, including the acceptable range of measurements, under normal operating conditions. This data will help you recognize when the process or diagnostic variables are unusually high or low, and may help you diagnose and troubleshoot application issues.
Page 84: View Process Variables

Transmitter operation View process variables Display Scroll to the desired process variable. If AutoScroll is enabled, you can wait until the process variable is displayed. See Section 7.2.1 for more information. ProLink III View the desired variable on the main screen under Process Variables. See Section 7.2.2 for more information.
Page 85: View Process Variables And Other Data Using Prolink Iii

Transmitter operation Figure 7-1: Transmitter display features A. Status LED B. Display (LCD panel) C. Process variable D. Scroll optical switch E. Optical switch indicator: turns red when either Scroll or Select is activated F. Select optical switch G. Unit of measure for process variable H.
Page 86: View Transmitter Status Using The Status Led

Transmitter operation • To view a more complete set of process variables, plus the current state of the outputs, choose Service Tools > Variables. View transmitter status using the status LED The status LED shows the current alert condition of the transmitter. The status LED is located on the face of the transmitter.
Page 87: View And Acknowledge Status Alerts

Transmitter operation Table 7-1: Transmitter status reported by status LED (continued) LED state Description Recommendation Flashing red (if ena- One or more high-severity alerts are active A high-severity alert condition affects meas- bled) and have not been acknowledged. urement accuracy and output behavior. Re- solve the alert condition before continuing.
Page 88
Transmitter operation Figure 7-2: Using the display to view and acknowledge the status alerts Scroll and Select simultaneously for 4 seconds SEE ALARM Select Is ACK ALL enabled? ACK ALL Select Scroll EXIT Select Scroll Active/ unacknowledged alarms? Alarm code NO ALARM Scroll Select…
Page 89: View And Acknowledge Alerts Using Prolink Iii

Transmitter operation Postrequisites • To clear the following alerts, you must correct the problem, acknowledge the alert, then power-cycle the transmitter: A001, A002, A010, A011, A012, A013, A018, A019, A022, A023, A024, A025, A028, A029, A031. • For all other alerts: If the alert is inactive when it is acknowledged, it will be removed from the list.
Page 90: View Alerts Using The Field Communicator

Transmitter operation If the alert is active when it is acknowledged, it will be removed from the list when the alert condition clears. Related information Alert data in transmitter memory 7.4.3 View alerts using the Field Communicator You can view a list containing all alerts that are active, or inactive but unacknowledged. •…
Page 91: Alert Data In Transmitter Memory

Transmitter operation 7.4.5 Alert data in transmitter memory The transmitter maintains three sets of data for every alert that is posted. For each alert occurrence, the following three sets of data are maintained in transmitter memory: • Alert List • Alert Statistics •…
Page 92: Start And Stop Totalizers And Inventories

Transmitter operation Start and stop totalizers and inventories Display Section 7.6.1. ProLink III Device Tools > Totalizer Control > Totalizer and Inventories > Start All Totals Device Tools > Totalizer Control > Totalizer and Inventories > Stop All Totals Field Communicator Service Tools > Variables > Totalizer Control > All Totalizers > Start Totalizers Service Tools >…
Page 93: Reset Totalizers

Transmitter operation Exit displays beneath the current totalizer value. 4. Select. 5. Select again to confirm. 6. Scroll to EXIT. • To stop all totalizers and inventories using the display: 1. Scroll until the word TOTAL appears in the lower left corner of the display. Important Because all totalizers are started or stopped together, it does not matter which total you use.
Page 94: Reset Totalizers Using The Display

Transmitter operation 7.7.1 Reset totalizers using the display Prerequisites • The Totalizer Reset display function must be enabled. • The totalizer that you want to reset must be configured as a display variable. For example: If you want to reset the mass totalizer, Mass Total must be configured as a display variable.
Page 95: Reset Inventories

Transmitter operation Exit displays beneath the current totalizer value. 3. Scroll until Reset displays beneath the current totalizer value. 4. Select. Reset and Yes? alternately flash beneath the current totalizer value. 5. Select again to confirm. 6. Scroll to EXIT. 7.
Page 96
Transmitter operation Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 97: Chapter 8 Measurement Support

Measurement support Measurement support Topics covered in this chapter: • Options for measurement support • Use Smart Meter Verification (SMV) • Zero the meter • Validate the meter • Perform a (standard) D1 and D2 density calibration • Perform temperature calibration Options for measurement support Micro Motion provides several measurement support procedures to help you evaluate and maintain your flowmeter’s accuracy.
Page 98: Smv Requirements

Measurement support 8.2.1 SMV requirements To use SMV, the transmitter must be paired with an enhanced core processor. Table 8‐1 for the minimum version of the transmitter, enhanced core processor, and communication tool needed to support SMV. (If you are going to perform SMV using the display, only the transmitter and enhanced core processor versions apply.) Table 8-1: Minimum SMV version…
Page 99: Run Smv

Measurement support SMV has an output mode called Continuous Measurement that allows the transmitter to keep measuring while the test is in progress. If you choose to run the test in Last Measured Value or Fault modes instead, the transmitter outputs will be held constant for the two minute duration of the test.
Page 100
Measurement support Option Description Last Value During the test, all outputs will report the last measured value of their as- signed process variable. The test will run for approximately 140 seconds. While the test is in progress, dots traverse the display and test progress is shown. Postrequisites View the test results and take any appropriate actions.
Page 101
Measurement support Enter any desired information on the Test Definition screen, and click Next. All information on this screen is optional. Choose the desired output behavior. Option Description Continue Measur- During the test, all outputs will continue to report their assigned process variable.
Page 102: View Test Data

Measurement support 8.2.4 View test data You can view the results of the current test. You can also view results from previous tests. Important You can view previous test results and see detailed test reports only if SMV is licensed. The transmitter stores the following information about the previous twenty SMV tests: •…
Page 103
Measurement support b. Scroll to Results Read and press Select. The runcount of the most recent test is displayed. c. To view data for this test, press Select, then press Scroll to scroll through test data. d. To select a different test, press Scroll, then press Select when the transmitter displays Results More?.
Page 104
Measurement support View test result data using ProLink III Prerequisites You can view test result data only if your SMV is licensed and only for tests that were run on the PC you are currently using. Procedure Choose Device Tools > Diagnostics > Meter Verification and click Previous Test Results.
Page 105: Schedule Automatic Execution Of The Smv Test

Measurement support • If the meter passes the second test, the first result can be ignored. • If the meter fails the second test, the flow tubes may be damaged. Call customer support. Abort A problem occurred with the meter verification test (such as process instability) or you stopped the test manually.
Page 106
Measurement support Figure 8-5: SMV – Top-level menu Scroll and Select simultaneously for 4 seconds Scroll ENTER METER VERFY Select RUN VERFY RESULTS READ SCHEDULE VERFY EXIT Scroll Scroll Scroll Select Select Select Scroll Select Scroll to Schedule Verfy and press Select. To schedule a single test or the first test in recurring execution: a.
Page 107
Measurement support SMV flowchart: Scheduling test execution using the display Figure 8-6: Scheduling SMV test execution using the display SCHEDULE VERFY Select Schedule set? SCHED IS OFF TURN OFF SCHED/YES? Scroll Scroll Select Schedule deleted HOURS LEFT Scroll Select xx HOURS Select SET NEXT SET RECUR…
Page 108: Zero The Meter

Measurement support To schedule recurring execution, specify a value for Hours Between Recurring Runs. To disable scheduled execution: • To disable execution of a single scheduled test, set Hours Until Next Run to 0. • To disable recurring execution, set Hours Between Recurring Runs to 0. •…
Page 109: Validate The Meter

Measurement support If necessary, modify Zero Time. Zero Time controls the amount of time the transmitter takes to determine its zero-flow reference point. The default Zero Time is 20 seconds. For most applications, the default Zero Time is appropriate. Postrequisites Restore normal flow through the sensor by opening the valves.
Page 110
Measurement support If you plan to calculate the meter factor for volume flow, be aware that validating volume in the field may be expensive, and the procedure may be hazardous for some process fluids. Therefore, because volume is inversely proportional to density, an alternative to direct measurement is to calculate the meter factor for volume flow from the meter factor for density.
Page 111: Alternate Method For Calculating The Meter Factor For Volume Flow

Measurement support 8.4.1 Alternate method for calculating the meter factor for volume flow The alternate method for calculating the meter factor for volume flow is used to avoid the difficulties that may be associated with the standard method. This alternate method is based on the fact that volume is inversely proportional to density. It provides partial correction of the volume flow measurement by adjusting for the portion of the total offset that is caused by the density measurement offset.
Page 112: Perform A D1 And D2 Density Calibration Using Prolink Iii

Measurement support Prerequisites • During density calibration, the sensor must be completely filled with the calibration fluid, and flow through the sensor must be at the lowest rate allowed by your application. This is usually accomplished by closing the shutoff valve downstream from the sensor, then filling the sensor with the appropriate fluid.
Page 113: Perform A D1 And D2 Density Calibration Using An Enhanced Ff Host

Measurement support Postrequisites If you disabled LD Optimization before the calibration procedure, re-enable it. 8.5.2 Perform a D1 and D2 density calibration using an enhanced FF host Read the Prerequistes on page 104 if you have not already done so. See the following figure.
Page 114: Perform Temperature Calibration

Measurement support Perform temperature calibration Temperature calibration establishes the relationship between the temperature of the calibration fluids and the signal produced by the sensor. Prerequisites The temperature calibration is a two-part procedure: temperature offset calibration and temperature slope calibration. The two parts must be performed without interruption, in the order shown.
Page 115: Perform Temperature Calibration Using A Fieldbus Host

Measurement support Important Consult customer support before performing a temperature calibration. Under normal circumstances, the temperature circuit is stable and should not need an adjustment. 8.6.1 Perform temperature calibration using a fieldbus host Write the temperature units to be used for calibration to Calibration TB > CAL_TEMPERATURE_UNITS (OD Index 56).
Page 116
Measurement support Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 117: Chapter 9 Troubleshooting

Troubleshooting Troubleshooting Topics covered in this chapter: • Status alerts, causes, and recommendations • Flow measurement problems • Density measurement problems • Temperature measurement problems • Check power supply wiring • Check grounding • Check for radio frequency interference (RFI) •…
Page 118
Troubleshooting Alert num- Alert title Possible cause Recommended actions A004 Temperature Over- The RTD resistance is out of range • Check your process conditions against range for the sensor. The tube RTD resist- the values reported by the device. ance is out of range for the sensor. •…
Page 119
Troubleshooting Alert num- Alert title Possible cause Recommended actions A009 Transmitter Initializ- Transmitter is in power-up mode. • Allow the meter to complete its power- ing/Warming Up up sequence. The alert should clear au- tomatically. • If other alerts are present, resolve those alert conditions first.
Page 120
Troubleshooting Alert num- Alert title Possible cause Recommended actions A013 Zero Calibration There was too much process insta- • Remove or reduce sources of electro- Failed: Unstable bility during the calibration proce- mechanical noise (e.g., pumps, vibra- dure. tion, pipe stress), cycle power to the meter, then retry the procedure.
Page 121
Troubleshooting Alert num- Alert title Possible cause Recommended actions A021 Transmitter/Sensor/ The configured board type does not • Verify all of the characterization or cali- Software Mismatch match the physical board, or the bration parameters. See the sensor tag configured sensor type does not or the calibration sheet for your meter.
Page 122
Troubleshooting Alert num- Alert title Possible cause Recommended actions A031 Low Power The transmitter is not receiving • Check the wiring between the transmit- enough power. ter and the core processor, then cycle power to the meter. This alert will not clear until you cy- •…
Page 123
Troubleshooting Alert num- Alert title Possible cause Recommended actions A102 Drive Overrange The drive power (current/voltage) is • Check the drive gain and the pickoff at its maximum. voltage. • Check the wiring between the sensor and the transmitter. • Verify that internal wiring is secure and that there are no internal electrical problems.
Page 124: Flow Measurement Problems

Troubleshooting Alert num- Alert title Possible cause Recommended actions A131 Meter Verification in A meter verification test is in pro- • Allow the procedure to complete. Progress: Outputs to gress, with outputs set to Last Meas- Last Measured Value ured Value. A132 Sensor Simulation Sensor simulation is enabled.
Page 125
Troubleshooting Problem Possible causes Recommended actions Erratic non-zero flow • Leaking valve or seal • Verify that the sensor orientation is appro- rate at no-flow condi- • Two-phase flow priate for your application (refer to the tions • Plugged or coated sensor tube sensor installation manual).
Page 126: Density Measurement Problems

Troubleshooting Problem Possible causes Recommended actions Inaccurate flow rate • Wiring problem • Check the wiring between the sensor and or batch total • Inappropriate measurement unit the transmitter. • Incorrect flow calibration factor • Verify that the measurement units are con- •…
Page 127: Temperature Measurement Problems

Troubleshooting Problem Possible causes Recommended actions Unusually high densi- • Plugged or coated sensor tube • Ensure that all of the calibration parame- ty reading • Incorrect density calibration factors ters have been entered correctly. See the • Incorrect temperature measurement sensor tag or the calibration sheet for your •…
Page 128: Check Power Supply Wiring

Troubleshooting Check power supply wiring If the power supply wiring is damaged or improperly connected, the transmitter may not receive enough power to operate properly. Prerequisites • You will need the installation manual for your transmitter. • When using DC power, a minimum of 1.5 amps of startup current is required. •…
Page 129: Check Grounding

Troubleshooting Check grounding A sensor and the transmitter must be grounded. Prerequisites You will need an: • Installation manual for your sensor • Installation manual for your transmitter (remote-mount installations only) Procedure Refer to the sensor and transmitter installation manuals for grounding requirements and instructions.
Page 130: Check The Drive Gain

Troubleshooting Check the settings of Two-Phase Flow Low Limit, Two-Phase Flow High Limit, and Two-Phase Flow Timeout. You can reduce the occurrence of two-phase flow alerts by setting Two-Phase Flow Low Limit to a lower value, Two-Phase Flow High Limit to a higher value, or Two-Phase Flow Timeout to a higher value.
Page 131: Collect Drive Gain Data

Troubleshooting Table 9-1: Possible causes and recommended actions for excessive (saturated) drive gain (continued) Possible cause Recommended actions Vibrating element Ensure that the vibrating element is free to vibrate. not free to vibrate Erratic drive gain Table 9-2: Possible causes and recommended actions for erratic drive gain Possible cause Recommended actions Foreign material…
Page 132: Collect Pickoff Voltage Data

Troubleshooting Table 9-3: Possible causes and recommended actions for low pickoff voltage (continued) Possible cause Recommended actions The vibrating element is not vibrating • Check for plugging or deposition. • Ensure that the vibrating element is free to vi- brate (no mechanical binding). Moisture in the sensor electronics Eliminate the moisture in the sensor electronics.
Page 133
Troubleshooting Procedure Disconnect power to the transmitter. DANGER! If the transmitter is in a hazardous area, wait 5 minutes before continuing. Unplug the terminal blocks from the terminal board on the core processor. Using a digital multimeter (DMM), check the pickoff coils by placing the DMM leads on the unplugged terminal blocks for each terminal pair.
Page 134
Troubleshooting With the DMM set to its highest range, there should be infinite resistance on each lead. If there is any resistance at all, there is a short to case. Test the resistance of junction box terminal pairs. a. Test the brown terminal against all other terminals except the red one. b.
Page 135: Appendix A Transducer Blocks And Views

Transducer blocks and views Appendix A Transducer blocks and views Topics covered in this appendix: • Descriptions of transducer block table entries • Measurement transducer blocks • Calibration transducer blocks • Diagnostics transducer blocks • Device information transducer blocks • Local display transducer blocks •…
Page 136: Descriptions Of Transducer Block Table Entries

Transducer blocks and views Descriptions of transducer block table entries Use the following definitions for the transducer block details tables: Index of the FOUNDATION Fieldbus parameter in the object dictionary Name Name of the fieldbus parameter used in the code Description Provides a description of the parameter.
Page 137: Measurement Transducer Blocks

Transducer blocks and views Table A-2: Access (continued) RW (Auto) Read/write, with the transducer block in Auto mode List of values The list of valid values to write to an enumerated parameter. This field is not applicable for read only parameters. Valid value ranges for variable type parameters are specified in the tables.
Page 138
Transducer blocks and views Table A-3: Measurement transducer block parameters view list (continued) View Index Name ST_REV TAG_DESC — — — — STRATEGY — — — ALERT_KEY — — — MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — —…
Page 139
Transducer blocks and views Table A-3: Measurement transducer block parameters view list (continued) View Index Name MFLOW_M_FACTOR — — — DENSITY_M_FACTOR — — — VOL_M_FACTOR — — — MASS_LOW_CUT — — — VOLUME_FLOW_LOW_CUTOFF — — — DENSITY_LOW_CUTOFF — — — FLOW_DIRECTION —…
Page 140: Standard Fieldbus Parameters For Measurement Transducer Blocks

Transducer blocks and views Table A-3: Measurement transducer block parameters view list (continued) View Index Name SNS_GSVflowBaseUnit — — — SNS_GSVflowBaseTime — — — SNS_GSVflowFactor — — — SNS_GSVflowText — — — SNS_GSVtotText — — — SNS_GSV_FlowCutoff — — — SNS_ResetGSVolTotal —…
Page 141
Transducer blocks and views Index and name Description List of values The user description of the intended block Any 32 characters application. TAG_DESC Msg type = STR Data type = OCTET STRING (32) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 Used to identify grouping of blocks.
Page 142
Transducer blocks and views Index and name Description List of values Occurs when a static parameter is changed — while a block mode is not in out of service UPDATE_EVT (OOS) mode, or when the mode changes from OOS mode and one or more static pa- rameters changed while the block was OOS.
Page 143: Process Variables For Measurement Transducer Blocks

Transducer blocks and views Index and name Description List of values Used for all config, H/W, connection failure 0 = No Error of system problems in the block. 18 = Calibration Error XD_ERROR 19 = Configuration Error Msg type = VAR 20 = Electronics Failure Data type = Unsigned8 (1) 21 = Sensor Failure…
Page 144
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Base mass unit 1089 = g 1088 = kg MFLOW_SPECIAL_UNIT_ Msg type = ENUM 1092 = t BASE Data type = Unsigned16 (2) 1094 = lb Store = Static 1095 = STon…
Page 145
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Density unit 1097 = kg/m3 1100 = g/cm3 DENSITY_UNITS Msg type = ENUM 1103 = kg/L Data type = Unsigned16 (2) 1104 = g/ml Store = Static 1105 = g/L…
Page 146
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Standard or special volume flow 1347 = m3/s rate unit 1348 = m 3/min VOLUME_FLOW_UNITS 1349 = m3/h CDM (2.0 and Msg type = ENUM 1350 = m3/d above)
Page 147
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Special volume unit conversion fac- — VOL_SPECIAL_UNIT_CONV Msg type = VAR Data type = FLOAT (4) Store = Static Access = RW (OOS) Available in Release 1.0 Special volume unit string Any 8 characters…
Page 148
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Density internal damping in sec- — onds DENSITY_DAMPING Msg type = VAR Data type = FLOAT (4) Store = Static Access = RW (OOS) Available in Release 1.0 Mass rate factor…
Page 149
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Flow direction 0 = Forward Only 1 = Reverse Only FLOW_DIRECTION Msg type = ENUM 2 = Bi-Directional Data type = Unsigned16 (2) 3 = Absolute Value Store = Static 4 = Negate/Forward Only…
Page 150: Totalizers For Measurement Transducer Blocks

Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Low density limit of sensor in g/cc — LOW_DENSITY_LIMIT Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 1.0 Low volume flow limit of sensor…
Page 151
Transducer blocks and views Table A-5: Totalizers for measurement transducer blocks (continued) Index and name Description List of values Reset all totals Value part of DS-66 1 = Reset RESET_TOTALS Msg type = VAR Data type = DS-66 (2) Store = — Access = R/W in any mode Available in Release 1.0 Reset all inventories…
Page 152: Gas Process Variables For Measurement Tranducer Blocks

Transducer blocks and views Table A-5: Totalizers for measurement transducer blocks (continued) Index and name Description List of values Volume inventory — VOLUME_INVENTORY Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 1.0 Standard or special mass total and 1089 = g mass inventory unit…
Page 153
Transducer blocks and views Table A-6: Gas process variables for measurement transducer blocks (continued) Index and name Description List of values Reference volume gas total (not — valid when petroleum measure- GSV_Vol_Tot ment or concentration measure- ment is enabled) Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only…
Page 154
Transducer blocks and views Table A-6: Gas process variables for measurement transducer blocks (continued) Index and name Description List of values Gas standard volume total and in- 1053 = SCF ventory engineering units 1521 = Nm3 SNS_GSV_TotalUnits 1526 = Sm3 Msg type = ENUM 1531 = NL Data type = Unsigned16 (2)
Page 155: Other Additions For Measurement Transducer Blocks

Transducer blocks and views Table A-6: Gas process variables for measurement transducer blocks (continued) Index and name Description List of values Gas standard volume low flow cut- Must be >= 0.0 SNS_GSV_FlowCutoff Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W OOS Available in Release 4.0…
Page 156: Calibration Transducer Blocks

Transducer blocks and views Table A-7: Other additions for measurement transducer blocks (continued) Index and name Description List of values Indicates whether flow is moving in Value part of DS-66 the forward or reverse direction 0 = Forward or Zero Flow SNS_ActualFlowDirection 1 = Reverse Flow Msg type = VAR…
Page 157: Mode_Blk

Transducer blocks and views View Index Name MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — — BLOCK_ALM — — — — TRANSDUCER_DIRECTORY — — — — TRANSDUCER_TYPE TRANSDUCER_TYPE_VER XD_ERROR — — COLLECTION_DIRECTORY — — — — MASS_FLOW_GAIN — —…
Page 158: Standard Fieldbus Parameters For Calibration Transducer Blocks

Transducer blocks and views View Index Name T_DENSITY_FQ_COEFF1 — — — T_DENSITY_FQ_COEFF2 — — — TEMP_LOW_CAL — — — TEMP_HIGH_CAL — — — TEMP_VALUE — — — TEMP_OFFSET — — — TEMP_SLOPE — — — PRESSURE_COMP — — PRESSURE_UNITS — —…
Page 159
Transducer blocks and views Index and name Description List of values The revision level of the static data associ- — ated with the function block. Incremented ST_REV with each write of static store. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = Read only Available in Release 1.0…
Page 160
Transducer blocks and views Index and name Description List of values Occurs when a static parameter is changed — while a block mode is not in out of service UPDATE_EVT (OOS) mode, or when the mode changes from OOS mode and one or more static pa- rameters changed while the block was OOS.
Page 161: Calibration Transducer Blocks

Transducer blocks and views Index and name Description List of values Used for all config, H/W, connection failure 0 = No Error of system problems in the block. 18 = Calibration Error XD_ERROR 19 = Configuration Error Msg type = VAR 20 = Electronics Failure Data type = Unsigned8 (1) 21 = Sensor Failure…
Page 162
Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values Standard deviation of auto zero — ZERO_STD_DEV Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 1.0 Present flow signal offset at zero —…
Page 163
Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values Perform fourth point calibration 0 = None 1 = Start Cal D4_DENSITY_CAL Msg type = METHOD Data type = Unsigned16 (2) Store = — Access = R/W (OOS) Available in Release 1.0 Density calibration constant 1…
Page 164
Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values Density 1 (g/cc) — Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 1.0 Density 2 (g/cc) —…
Page 165
Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values T-Series: Flow FQ Coefficient (FFQ) — T_FLOW_FQ_COEFF Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 1.0 T-Series: Density TG Coefficient —…
Page 166: Pressure Compensation For Calibration Transducer Blocks

Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values Temperature value for tempera- — ture calibrations (in degC) TEMP_VALUE Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 1.0 Temperature calibration offset —…
Page 167
Transducer blocks and views Table A-9: Pressure compensation for calibration transducer blocks (continued) Index and name Description List of values Pressure unit 1148 = inH2O (68°F) 1724 = InH2O@60°F PRESSURE_UNITS Msg type = ENUM 1156 = inHg (0°C) Data type = Unsigned16 (2) 1154 = ftH2O (68°F) Store = Static 1151 = mmH2O (68°F)
Page 168: Temperature Compensation For Calibration Transducer Blocks

Transducer blocks and views A.3.5 Temperature compensation for calibration transducer blocks Table A-10: Temperature compensation for calibration transducer blocks Index and name Description List of values Enable/Disable temperature com- 0 = disabled pensation 1 = enabled SNS_ PuckEnableExtTemp Msg type = METHOD Data type = Unsigned16 (2) Store = Static Access = R/W (OOS)
Page 169: Diagnostics Transducer Blocks

Transducer blocks and views Table A-11: Other additions for calibration transducer blocks (continued) Index and name Description List of values Pressure input type 1 = Digital Comm 2 = Fixed PRESSURE_INPUT_TYPE Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 9.0…
Page 170
Transducer blocks and views View Index Name SLUG_LOW_LIMIT — — — — — SLUG_HIGH_LIMIT — — — — — ALARM1_STATUS — — — — ALARM2_STATUS — — — — ALARM3_STATUS — — — — ALARM4_STATUS — — — — FAULT_LIMIT —…
Page 171
Transducer blocks and views View Index Name MFP_TYPE — — — — — MFP_TV_INST — — — — — MFP_TV_INST — — — — — MFP_TV_STD_DEV — — — — — MFP_TV_MAX — — — — — MFP_TV_MIN — — —…
Page 172
Transducer blocks and views View Index Name FRF_StiffnessRpo_ — — — — — stddev FRF_Damping_stddev — — — — — FRF_MassLpo_stddev — — — — — FRF_MassRpo_stddev — — — — — FRF_StiffnessLpo_air — — — — — FRF_StiffnessRpo_air — —…
Page 173
Transducer blocks and views View Index Name FRF_MV_Elapse_Time — — — — — FRF_MV_Time_Left — — — — — FRF_ToneLevel — — — — — FRF_ToneRampTime — — — — — FRF_BlCoeff — — — — — FRF_DriveTarget — — —…
Page 174: Standard Fieldbus Parameters For Diagnostic Transducer Blocks

Transducer blocks and views A.4.2 Standard fieldbus parameters for diagnostic transducer blocks Index and name Description List of values The beginning of the transducer block. — BLOCK_STRUCTURE Msg type = VAR Data type = DS_64 (5) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 The revision level of the static data associ- —…
Page 175
Transducer blocks and views Index and name Description List of values The actual, target, permitted, and normal See section 2.6 of FF-891 modes of the block. MODE_BLK Msg type = REC Data type = DS-69 (4) Store = Mixed Access = RW (OOS) or RW (Auto) Available in Release 1.0 The error status associated with the hard- See section 4.8 of FF-903…
Page 176: Slug Flow Setup For Diagnostic Transducer Blocks

Transducer blocks and views Index and name Description List of values Identifies the version of the transducer — block. Format is XXYY where XX is the ma- TRANSDUCER_ jor spec revision and YY is the manufacturer TYPE_VER revision. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = RW (OOS)
Page 177: Alarm Status For Diagnostic Transducer Blocks

Transducer blocks and views Table A-12: Slug flow setup for diagnostic transducer blocks (continued) Index and name Description List of values High density limit in g/cc — SLUG_HIGH_LIMIT Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W in any mode Available in Release 1.0 A.4.4…
Page 178
Transducer blocks and views Table A-13: Alarm status for diagnostic transducer blocks (continued) Index and name Description List of values Status Word 2 0x0001 = Line RTD Over 0x0002 = Meter RTD Over ALARM2_STATUS Msg type = ENUM 0x0004 = CP Exception Data type = BIT STRING (2) 0x0008 = API: Temp OOL Store = Dynamic/20…
Page 179
Transducer blocks and views Table A-13: Alarm status for diagnostic transducer blocks (continued) Index and name Description List of values Status Word 4 0x0001 = Cal Fail: Low 0x0002 = Cal Fail: High ALARM4_STATUS Msg type = ENUM 0x0004 = Cal Fail: Noisy Data type = BIT STRING (2) 0x0008 = Auto Zero IP Store = Dynamic/20…
Page 180
Transducer blocks and views Table A-13: Alarm status for diagnostic transducer blocks (continued) Index and name Description List of values Alarm index 0 = No Alarm 1 = A001 — (E)EPROM Error (CP) ALARM_INDEX Msg type = ENUM 2 = A002 — RAM Error (CP) Data type = Unsigned16 (2) 3 = A003 — Sensor Failure Store = Static…
Page 181
Transducer blocks and views Table A-13: Alarm status for diagnostic transducer blocks (continued) Index and name Description List of values Failed 35 = A035 — Meter Verification Aborted 36 = A036 — Viscosity Out of Lim- 37 = A037 — Sensor Check Failed 38 = A038 — Time Period Out of Range 42 = A102 — Drive Overrange/Par-…
Page 182: Device Diagnostics From Diagnostics Transducer Block

Transducer blocks and views A.4.5 Device diagnostics from diagnostics transducer block Table A-14: Device diagnostics from diagnostics transducer block List of Index and name Description values Drive gain — DRIVE_GAIN Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 1.0 Raw tube period…
Page 183
Transducer blocks and views Table A-14: Device diagnostics from diagnostics transducer block (continued) List of Index and name Description values Maximum electronics temperature — ELECT_TEMP_ Msg type = VAR Data type = FLOAT (4) Store = Dynamic/20 Access = Read only Available in Release 2.0 Minimum electronics temperature —…
Page 184: Meter Fingerprinting For Diagnostic Transducer Blocks

Transducer blocks and views Table A-14: Device diagnostics from diagnostics transducer block (continued) List of Index and name Description values Meter RTD resistance in ohms — RTD_RESISTANCE_ Msg type = VAR METER Data type = FLOAT (4) Store = Dynamic/20 Access = Read only Available in Release 3.0 Number of core processor power cycles…
Page 185
Transducer blocks and views Table A-15: Meter fingerprinting for diagnostic transducer blocks (continued) Index and name Description List of values Meter fingerprint in SI (0) or English 0x0000 = SI (1) units 0x0001 = English MFP_UNITS Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W in any mode…
Page 186: Other Additions For Diagnostics Transducer Blocks

Transducer blocks and views Table A-15: Meter fingerprinting for diagnostic transducer blocks (continued) Index and name Description List of values Transmitter variable, maximum — (since last statistics reset) MFP_TV_MAX Msg type = VAR Data type = FLOAT (4) Store = Dynamic Access = Read only Available in Release 3.0 Transmitter variable, minimum…
Page 187
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values Actual target amplitude (mV/Hz) — (pre 700 2.1, actual & override) SNS_TargetAmplitude Msg type = VAR Data type = FLOAT (4) Store = Dynamic Access = Read only Available in Release 4.0…
Page 188
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values Start/Stop meter verification — (ap- 0= Disabled plicable only if meter verification is 1 = Fixed output mode FRF_EnableFCFValidation enabled) 2 = Factory air verification 3 = Factory water verification Msg type = METHOD…
Page 189
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The reason the meter verification 0 = No error routine aborted 1 = Manual abort FRF_AbortCode 2 = Watchdog timeout Msg type = ENUM 3 = Frequency drift Data type = Unsigned16 (2)
Page 190
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The current RPO stiffness calcula- — ted as a mean FRF_StiffnessRpo_mean Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 4.0…
Page 191
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The current damping calculated as — a standard deviation FRF_Damping_stddev Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 4.0 The current LPO mass calculated as…
Page 192
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The LPO mass calculated as a mean — during Factory Cal of Air FRF_MassLpo_air Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 4.0…
Page 193
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The RPO mass calculated as a mean — during Factory Cal of Water FRF_MassRpo_water Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 4.0…
Page 194
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values FCF Datalog Item 2: Status; Abort Bit 7 = FCF pass/fail states are compressed to fit into 3 Bits 6-4 = state FRF_MV_Status bits Bits 3-0 = abort code…
Page 195
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #100 Temperature — FRF_Temp Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 6.0 #101 Density…
Page 196
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #106 FCF timers: time until first run in — hours (applicable only if meter veri- FRF_MV_FirstRun_Time fication feature is enabled) Msg type = VAR Data type = FLOAT (4) Store = Static…
Page 197
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #111 BL coefficient (applicable only if — meter verification feature is ena- FRF_BlCoeff bled) Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 7.0…
Page 198
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #116 Maximum sensor current (applica- — ble only if meter verification feature FRF_Max_Current_mA is enabled) Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 7.0…
Page 199
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #121 Temperature unit 1000 = K 1001 = Deg C DIAG_TEMPERATURE_ Msg type = ENUM 1002 = Deg F UNITS Data type = Unsigned16 (2) 1003 = Deg R Store = Static…
Page 200: Device Information Transducer Blocks

Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #126 Indexed by R2984 — DIAG_FRF_RPO_METER_ Msg type = VAR FACTOR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 8.0 #127 Indexed by R2984…
Page 201
Transducer blocks and views View Index Name STRATEGY — — — ALERT_KEY — — — MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — — BLOCK_ALM — — — — TRANSDUCER_DIRECTORY — — — — TRANSDUCER_TYPE TRANSDUCER_TYPE_VER XD_ERROR — —…
Page 202: Standard Fieldbus Parameters For Device Information Transducer Blocks

Transducer blocks and views A.5.2 Standard fieldbus parameters for device information transducer blocks Index and name Description List of values The beginning of the transducer block. — BLOCK_STRUCTURE Msg type = VAR Data type = DS_64 (5) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 The revision level of the static data associ-…
Page 203
Transducer blocks and views Index and name Description List of values The actual, target, permitted, and normal See section 2.6 of FF-891 modes of the block. MODE_BLK Msg type = REC Data type = DS-69 (4) Store = Mixed Access = RW (OOS) or RW (Auto) Available in Release 1.0 The error status associated with the hard- See section 4.8 of FF-903…
Page 204: Transmitter Data For Device Information Transducer Blocks

Transducer blocks and views Index and name Description List of values Identifies the version of the transducer — block. Format is XXYY where XX is the ma- TRANSDUCER_ jor spec revision and YY is the manufacturer TYPE_VER revision. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = RW (OOS)
Page 205: Sensor Data For Device Information Transducer Blocks

Transducer blocks and views Table A-17: Transmitter data for device information transducer blocks (continued) Index and name Description List of values Model 700 transmitter software re- — vision 700_SW_REV Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = Read only Available in Release 1.0 Model 2700 transmitter software…
Page 206
Transducer blocks and views Table A-18: Sensor data for device information transducer blocks (continued) Index and name Description List of values Sensor type (i.e. F200, CMF025) — SENSOR_TYPE Msg type = STR Data type = VISIBLE STRING (16) Store = Static Access = Read only Available in Release 1.0 Sensor type code…
Page 207
Transducer blocks and views Table A-18: Sensor data for device information transducer blocks (continued) Index and name Description List of values Flange type 0 = ANSI 150 [CP, ECP, FDM, FVM] SENSOR_END Msg type = ENUM 1 = ANSI 300 Data type = Unsigned16 (2) 2 = ANSI 600 Store = Static…
Page 208
Transducer blocks and views Table A-18: Sensor data for device information transducer blocks (continued) Index and name Description List of values Device type for the attached core 40 = 700 [CP] processor 50 = 800 [ECP] SNS_PuckDeviceTypeCode 61 = Density Msg type = ENUM Data type = Unsigned16 (2) Store = Static…
Page 209: Local Display Transducer Blocks

Transducer blocks and views Local display transducer blocks A.6.1 View list for local display transducer block The following table lists the parameters contained in the transducer block for local display parameters. Four views are defined for the local display transducer block. The table also shows the applicable views for each parameter, and the size of the parameter in that view, in bytes.
Page 210: Standard Fieldbus Parameters For Local Display Transducer Blocks

Transducer blocks and views View Index Name LDO_VAR_3_CODE — — — LDO_VAR_4_CODE — — — LDO_VAR_5_CODE — — — LDO_VAR_6_CODE — — — LDO_VAR_7_CODE — — — LDO_VAR_8_CODE — — — LDO_VAR_9_CODE — — — LDO_VAR_10_CODE — — — LDO_VAR_11_CODE —…
Page 211
Transducer blocks and views Index and name Description List of values The revision level of the static data associ- — ated with the function block. Incremented ST_REV with each write of static store. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = Read only Available in Release 1.0…
Page 212
Transducer blocks and views Index and name Description List of values Occurs when a static parameter is changed — while a block mode is not in out of service UPDATE_EVT (OOS) mode, or when the mode changes from OOS mode and one or more static pa- rameters changed while the block was OOS.
Page 213: Local Display Transducer Blocks

Transducer blocks and views Index and name Description List of values Used for all config, H/W, connection failure 0 = No Error of system problems in the block. 18 = Calibration Error XD_ERROR 19 = Configuration Error Msg type = VAR 20 = Electronics Failure Data type = Unsigned8 (1) 21 = Sensor Failure…
Page 214
Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values Enable/Disable LDO offline menu fea- 0 = Disable ture 1 = Enable EN_LDO_OFFLINE_MENU Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W in any mode Available in Release 1.0…
Page 215
Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values Display the language selection 0 = English 1 = German UI_Language Msg type = ENUM 2 = French Data type = Unsigned16 (2) 3 = Reserved Store = Static 4 = Spanish…
Page 216
Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values #25 LDO_VAR_1_CODE Displays the variable associated with 0 = Mass Flow Rate [700, 800] #26 LDO_VAR_2_CODE the code on the LDO 1 = Temperature #27 LDO_VAR_3_CODE 2 = Mass Total [700, 800] Msg type = ENUM…
Page 217
Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values 63 = Gas Std Vol Total [700, 800] 64 = Gat Std Vol Inventory [700, 800] 69 = Live Zero [700, 800] 159 = User Defined Equation [CDM, FDM, FVM] 161 = Tube-Case Temperature…
Page 218: Petroleum Measurement Transducer Blocks

Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values Enable/Disable display status LED 0 = Disable blinking 1 = Enable UI_EnableStatusLedBlinking Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W in any mode Available in Release 4.0 Enable/Disable display alarm screen…
Page 219
Transducer blocks and views View Index Name BLOCK_STRUCTURE — — — — ST_REV TAG_DESC — — — — STRATEGY — — — ALERT_KEY — — — MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — — BLOCK_ALM — — —…
Page 220: Standard Fieldbus Parameters For Petroleum Measurement Transducer Blocks

Transducer blocks and views A.7.2 Standard fieldbus parameters for petroleum measurement transducer blocks Index and name Description List of values The beginning of the transducer block. — BLOCK_STRUCTURE Msg type = VAR Data type = DS_64 (5) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 The revision level of the static data associ-…
Page 221
Transducer blocks and views Index and name Description List of values The actual, target, permitted, and normal See section 2.6 of FF-891 modes of the block. MODE_BLK Msg type = REC Data type = DS-69 (4) Store = Mixed Access = RW (OOS) or RW (Auto) Available in Release 1.0 The error status associated with the hard- See section 4.8 of FF-903…
Page 222: Process Variables For Petroleum Measurement Transducer Blocks

Transducer blocks and views Index and name Description List of values Identifies the version of the transducer — block. Format is XXYY where XX is the ma- TRANSDUCER_ jor spec revision and YY is the manufacturer TYPE_VER revision. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = RW (OOS)
Page 223
Transducer blocks and views Table A-20: Process variables for petroleum measurement transducer blocks (continued) Index and name Description List of values Batch weighted average density — API_Ave_Corr_Density Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 3.0 Batch weighted average tempera- —…
Page 224: Setup Data For Petroleum Measurement Transducer Blocks

Transducer blocks and views A.7.4 Setup data for petroleum measurement transducer blocks Table A-21: Setup data for petroleum measurement transducer blocks Index and name Description List of values Enable/Disable petroleum measure- 0 = disabled ment 1 = enabled EN_API Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = Read only…
Page 225
Transducer blocks and views Table A-21: Setup data for petroleum measurement transducer blocks (continued) Index and name Description List of values Reset PM/GSV inventory 0 = No effect 1 = Reset SNS_ResetAPIGSVInv Msg type = METHOD Data type = Unsigned16 (2) Store = Static Access = R/W in any mode Available in Release 4.0…
Page 226
Transducer blocks and views Table A-21: Setup data for petroleum measurement transducer blocks (continued) Index and name Description List of values Standard or special volume flow rate 1347 = m3/s unit 1348 = m 3/min API_VOL_FLOW_UNITS 1349 = m3/h Msg type = ENUM 1350 = m3/d Data type = Unsigned16 (2) 1351 = L/s…
Page 227: Concentration Measurement Transducer Blocks

Transducer blocks and views Table A-21: Setup data for petroleum measurement transducer blocks (continued) Index and name Description List of values Pressure units 1148 = inH2O (68°F) 1724 = InH2O@60°F API_PressureUnit Msg type = ENUM 1156 = inHg (0°C) Data type = Unsigned16 (2) 1154 = ftH2O (68°F) Store = Static 1151 = mmH2O (68°F)
Page 228
Transducer blocks and views View Index Name BLOCK_STRUCTURE — — — — ST_REV TAG_DESC — — — — STRATEGY — — — ALERT_KEY — — — MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — — BLOCK_ALM — — —…
Page 229
Transducer blocks and views View Index Name ED_Temp_Index — — — ED_Conc_Index — — — ED_Temp_ISO — — — ED_Dens_At_Temp_ISO — — — ED_Dens_At_Temp_Coeff — — — ED_Conc_Label_55 — — — ED_Dens_At_Conc — — — ED_Dens_At_Conc_Coeff — — — ED_Conc_Label_51 —…
Page 230: Standard Fieldbus Parameters For Concentration Measurement Transducer Blocks

Transducer blocks and views View Index Name ED_SYS_AttachedCoreType — — — SNS_ED_ConcUnits_SpecialUnit — — — ED_MASSFLOW_UNITS — — — ED_VOL_TOT_UNITS — — — ED_MASS_TOT_UNITS — — — A.8.2 Standard fieldbus parameters for concentration measurement transducer blocks Index and name Description List of values The beginning of the transducer block.
Page 231
Transducer blocks and views Index and name Description List of values The identification number of the plant unit. 1 to 255 This information may be used in the host ALERT_KEY for sorting alarms, etc. Msg type = VAR Data type = Unsigned8 (1) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0…
Page 232
Transducer blocks and views Index and name Description List of values A directory that specifies the number and — starting indices of the data collections in TRANSDUCER_ the transducer block. DIRECTORY Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = RW (OOS) Available in Release 9.0…
Page 233: Process Variables For Concentration Measurement Transducer Blocks

Transducer blocks and views A.8.3 Process variables for concentration measurement transducer blocks Table A-22: Process variables for concentration measurement transducer blocks Index and name Description List of values Density at reference — ED_Ref_Dens Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 3.0…
Page 234: Totals For Concentration Measurement Transducer Blocks

Transducer blocks and views Table A-22: Process variables for concentration measurement transducer blocks (continued) Index and name Description List of values Density (fixed baume units) — ED_Baume Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 3.0 A.8.4 Totals for concentration measurement transducer…
Page 235: Setup Data For Concentration Measurement Transducer Blocks

Transducer blocks and views Table A-23: Totals for concentration measurement transducer blocks (continued) Index and name Description List of values Net volume inventory — ED_Net_Vol_Inv Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 3.0 Reset concentration measurement Value part of DS-66…
Page 236
Transducer blocks and views Table A-24: Setup data for concentration measurement transducer blocks (continued) Index and name Description List of values Lock enhanced density tables 0 = not locked 1 = locked ED_Curve_Lock Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 3.0…
Page 237
Transducer blocks and views Table A-24: Setup data for concentration measurement transducer blocks (continued) Index and name Description List of values Curve (6×5) temperature iso- — therm value (x-axis) ED_Temp_ISO Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 3.0 Curve…
Page 238
Transducer blocks and views Table A-24: Setup data for concentration measurement transducer blocks (continued) Index and name Description List of values Curve (5×1) concentration value — (y-axis) ED_Conc_Label_51 Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 3.0 Curve…
Page 239
Transducer blocks and views Table A-24: Setup data for concentration measurement transducer blocks (continued) Index and name Description List of values Curve ASCII string – name of curve — – 12 characters supported ED_Curve_Name Msg type = VAR Data type = VISIBLE STRING (12) Store = Static Access = R/W in any mode Available in Release 3.0…
Page 240: Other Additions For Concentration Measurement Transducer Blocks

Transducer blocks and views A.8.6 Other additions for concentration measurement transducer blocks Table A-25: Other additions for concentration measurement transducer blocks Index and name Description List of values Reset concentration measurement 0 = No effect volume inventory 1 = Reset SNS_ResetEDVolInv Msg type = METHOD Data type = Unsigned16 (2)
Page 241
Transducer blocks and views Table A-25: Other additions for concentration measurement transducer blocks (continued) Index and name Description List of values Enable high density extrapolation 1 = Enable alarm SNS_ED_EnableDensHighEx- trap Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W in any mode Available in Release 4.0…
Page 242
Transducer blocks and views Table A-25: Other additions for concentration measurement transducer blocks (continued) Index and name Description List of values Standard or special volume flow rate 1347 = m3/s unit 1348 = m 3/min ED_VOL_FLOW_UNITS 1349 = m3/hr Msg type = ENUM 1350 = m3/day Data type = Unsigned16 (2) 1351 = L/s…
Page 243
Transducer blocks and views Table A-25: Other additions for concentration measurement transducer blocks (continued) Index and name Description List of values Enable concentration measurement 0 = disabled curve auto-switching 1 = enabled DEN_Enable_CMAutoswitch Msg type = VAR Data type = Unsigned16 (2) Store = —…
Page 244: Density Viscosity Meter Transducer Blocks

Transducer blocks and views Table A-25: Other additions for concentration measurement transducer blocks (continued) Index and name Description List of values Volume flow total unit 1034 = m3 1036 = cm3 ED_VOL_TOT_UNITS Msg type = ENUM 1038 = L Data type = Unsigned16 (2) 1043 = ft3 Store = Dynamic 1048 = gallon…
Page 245
Transducer blocks and views View Index Name TRANSDUCER_ — — — — — — — — DIRECTORY TRANSDUCER_TYPE — — — — TRANSDUCER_TYPE_ — — — — XD_ERROR — — — — — — COLLECTION_ — — — — — —…
Page 246
Transducer blocks and views View Index Name DEN_KV5 — — — — — — — DEN_KV6 — — — — — — — DEN_CalibrationStatus — — — — — — — DEN_KV_Index — — — — — — — DEN_KV_Crossover —…
Page 247
Transducer blocks and views View Index Name DEN_Programmable- — — — — — — — ConstF DEN_Programmable- — — — — — — — ValA DEN_Programmable- — — — — — — — ValB DEN_Programmable- — — — — — —…
Page 248
Transducer blocks and views View Index Name DEN_KinematicViscosi- — — — — — — — tyUnits VISC_RANGE_SEL_IN- — — — — — — — DEN_V0 — — — — — — — DEN_V1 — — — — — — — DEN_V2 —…
Page 249
Transducer blocks and views View Index Name MBUS_Visc_CurveIn- — — — — — — — MBUS_Visc_TempIn- — — — — — — — DEN_RefVisc_Mat_ — — — — — — — MaxFitOrder EN_RefVisc_Mat_Tem- — — — — — — — pISO DEN_RefVisc_Mat_Vis- —…
Page 250
Transducer blocks and views View Index Name DEN_CaseTemperatur- — — — — — — — eStability DEN_SpecialEquation- — — — — — — — Type DEN_Legacy_K0 — — — — — — — DEN_Legacy_K1 — — — — — — —…
Page 251: Standard Fieldbus Parameters For Density Viscosity Meter Transducer Blocks

Transducer blocks and views View Index Name PRESSURE_UNITS — — — — — — — DEN_ProductCode — — — — — — — — Velocity_Switch_Sta- — — — — — — — DEN_RefWaterDensity — — — — — — — DEN_RefTemperature —…
Page 252
Transducer blocks and views Index and name Description List of values The user description of the intended block Any 32 characters application. TAG_DESC Msg type = STR Data type = OCTET STRING (32) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 Used to identify grouping of blocks.
Page 253
Transducer blocks and views Index and name Description List of values Occurs when a static parameter is changed — while a block mode is not in out of service UPDATE_EVT (OOS) mode, or when the mode changes from OOS mode and one or more static pa- rameters changed while the block was OOS.
Page 254: Process Variables For Density Viscosity Transducer Blocks

Transducer blocks and views Index and name Description List of values Used for all config, H/W, connection failure 0 = No Error of system problems in the block. 18 = Calibration Error XD_ERROR 19 = Configuration Error Msg type = VAR 20 = Electronics Failure Data type = Unsigned8 (1) 21 = Sensor Failure…
Page 255
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Curve configuration index (n) 1 = Use user sensor check value DEN_UseUserSensorCheck Msg type = VAR 0 = Use factory sensor Value Data type = Unsigned16 (2) check value…
Page 256
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Densisty scale factor — DensityScaleFactor Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 8.0 Temperature scale factor —…
Page 257
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values K2, instrument calibration factor — DEN_K2 Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0 K18, instrument calibration factor —…
Page 258
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values KV calibration factor index (0-1) 0: Medium 1: High DEN_KV_Index Msg type = ENUM (1) Data type = Unsigned8 (1) Store = Static Access = R/W in any mode Available in Release 8.0…
Page 259
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values A6, density calibration constant — DEN_A6 Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0 A7, density calibration constant —…
Page 260
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Fixed flow velocity value (m/sec) — DEN_FixedVelocity Msg type = VAR Data type = DS65 Store = Dynamic/20 Access = Read only Available in Release 8.0 Flow velocity units 1061 = Meters/Sec-…
Page 261
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Time period (u/sec) (upper 3dB point) — DEN_TimePeriodB Msg type = VAR Data type = Float (4) Store = Dynamic/20 Access = Read only Available in Release 8.0 Time period (u/sec) (lower 3dB point)
Page 262: Den_Programmable

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Programmable constant E for special — equation (Y for special equation type I) DEN_ProgrammableConstE Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 263: Den_Programmable

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Programmable constant D for special — equation — constants available for access DEN_ProgrammableValD using pointers for special equations (reg- isters 4114-4119) Msg type = VAR Data type = Float (4)
Page 264: Den_Specialeqnslota

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Pointer A for special equation 1 = Temperature 3 = Density DEN_SpecialEqnSlotA Msg type = ENUM 5 = Volume Flow Rate Data type = Unsigned16 (2) [CDM] Store = Static…
Page 265: Den_Specialeqnslotb

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Pointer B for special equation See #74 DEN_Special- EqnSlotA DEN_SpecialEqnSlotB Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 266: Den_Qualityfactor

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Special equation unit string — DEN_SpecialEqnLabel Msg type = STR Data type = VISIBLE STRING Store = Static Access = R/W (OOS) Available in Release 8.0 Special density unit string —…
Page 267: Den_Dynamicviscosity

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Dynamic viscosity — DEN_DynamicViscosity Msg type = VAR Data type = DS65 Store = Dynamic Access = Read only Available in Release 8.0 Kinematic viscosity —…
Page 268
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values V2 at the selected range — Array of 4 — DEN_V2 Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 269
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #102 Special kinematic viscosity unit string Visible string DEN_KinViscSpecialUnitLabel Msg type = STR Data type = VISIBLE STRING Store = Static Access = R/W (OOS) Available in Release 8.0 #103…
Page 270
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #109 Average time period on air/vacuum (in- — dexed by DEN_KDV_CalIndex) DEN_AverageTimePeriod Msg type = VAR Data type = Float (4) Store = Static Access = Read only Available in Release 8.0…
Page 271
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #114 Referred viscosity calculation method 0 = referral matrix 1 = ASTM D341 single DEN_ReferredViscMethod Msg type = ENUM curve Data type = Unsigned16 (2) 2 = ASTM D341 multi-…
Page 272
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #119 Referred viscosity (6×6) @ temperature — isothermX, curve (indexed by MBUS_ DEN_RefVisc_Mat_ Visc_CurveIndex and MBUS_Visc_Tem- ViscAtTempISO pIndex) Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS)
Page 273
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #125 Number of ASTM reference curves (n = — 2-8) DEN_RefVisc_ASTM_NumCurves Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 274
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #130 Lab viscosity for viscosity scaling factor — calibration DEN_LabViscosity Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 275
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #137 Case temperature stability (sensor check) — DEN_CaseTemperatureStability Msg type = VAR Data type = Float (4) Store = Static Access = Read only Available in Release 8.0 #138…
Page 276
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #144 K20A constant used to compute K20 (in- — dexed by DEN_Legacy_K20_K21_Index) DEN_Legacy_K20A Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 277
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #150 Time period A (in microseconds) — DEN_TPA_Microsec Msg type = VAR Data type = DS65 Store = Dynamic Access = Read only Available in Release 8.0 #151…
Page 278
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #157 Index for KDV results 0 = Factory 1 = User DEN_KDV_CalIndex Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 279
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #163 Secondary referred viscosity — DEN_SecBaseViscosity Msg type = VAR Data type = DS65 Store = Dynamic Access = Read only Available in Release 8.0 #164 Unit for reference and secondary refer-…
Page 280
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #167 Pressure unit 1148 = inch water @ 68F / inch water@60F PRESSURE_UNITS Msg type = ENUM 1156 = inch HG @ 0C Data type = Unsigned16 (2) 1154 = ft water @ 68F Store = Dynamic…
Page 281
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #171 Reference temperature for inline calibra- — tion DEN_RefTemperature Msg type = VAR Data type = Float (4) Store = Static Access = R/W in any mode Available in Release 9.0 #172…
Page 282
Transducer blocks and views (1) The list within the square bracket contains cores that support this value. Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 283: Appendix B Fieldbus Channel References

Fieldbus channel references Appendix B Fieldbus channel references Table B-1: Analog input function blocks Channel number Channel description Valid unit code Core applicability Mass Flow Measurement TB > Mass Flow Units Temperature Measurement TB > Temperature Units Density Measurement TB > Density Units Volume Flow Measurement TB >…
Page 284
Fieldbus channel references Table B-1: Analog input function blocks (continued) Channel number Channel description Valid unit code Core applicability ED Specific Gravity Measurement TB > Density Units ED Std Vol Flow Measurement TB > Volume Flow Units ED Net Mass Flow Measurement TB >…
Page 285
Fieldbus channel references Table B-3: Discrete input function blocks (continued) Channel number Channel description Core applicability SNS ZeroInProgress SYS AnalogOutputFault SNS MVFailed Table B-4: Discrete output function blocks Channel number Channel description Core applicability Start Sensor Zero Reset Mass Total Reset Volume Total Reset API Reference (Standard) Volume Total Reset All Process Totals (not Inv)
Page 286
Fieldbus channel references Table B-5: AI function blocks Channel number Channel description Valid unit code Core applicability Special Equation Output 1588 = No Units Time Period A 1057 — Micro Second Time Period B 1057 — Micro Second Tube-case temperature differential Measurement TB >…
Page 287: Foundation

™ FOUNDATION fieldbus function blocks Appendix C ™ FOUNDATION fieldbus function blocks Topics covered in this appendix: • Analog Input (AI) function block • Analog Output (AO) function block • Integrator (INT) Function Block • Discrete Input (DI) function block •…
Page 288: Ai Block Modes

™ FOUNDATION fieldbus function blocks • OUT_SCALE: The high and low scale values, engineering units code, and number of digits to the right of the decimal point associated with OUT when L_TYPE is not direct. • SIMULATE: A group of data that contains the current transducer value and status, the simulated transducer value and status, and the enable/disable bit.
Page 289
™ FOUNDATION fieldbus function blocks CHANNEL Select the channel that corresponds to the desired sensor measurement. The following table provides a list of AI Function block channel numbers and channel applicability depending upon attached core type to transmitter. If a channel is not supported for the given core type, the channel value will not work for the transmitter.
Page 290
™ FOUNDATION fieldbus function blocks Table C-1: AI block channel definitions (continued) Channel Description Flow velocity (1) This channel assignment is supported only by CDM software revision 2.0 and above. L_TYPE The L_TYPE parameter defines the relationship of the sensor measurement to the desired output of the AI block.
Page 291: Ai Block Filtering

™ FOUNDATION fieldbus function blocks C.1.5 AI block filtering The filtering feature changes the response time of the device to smooth variations in output readings caused by rapid changes in input. Adjust the filter time constant (in seconds) using the PV_FTIME parameter. Set the filter time constant to zero to disable the filter feature.
Page 292: Ai Block Status Handling

™ FOUNDATION fieldbus function blocks Number Description The priority of an alarm condition changes to 0 after the condition that caused the alarm is corrected. An alarm condition with a priority of 1 is recognized by the system, but is not reported to the operator.
Page 293: Analog Output (Ao) Function Block

™ FOUNDATION fieldbus function blocks AI1 (AI_2600_ AI2 (AI_2800_ AI3 (AI3000_ AI4 (AI_3200_ xxxx) xxxx) xxxx) xxxx Channel Mass flow (1) Temperature (2) Density (3) Volume flow (4) OUT_SCALE EU_100 EU_0 Unit_Index Decimal L_TYPE Direct Direct Direct Direct Analog Output (AO) function block The AO block converts the FF value to a channel value by using two sets of scaling values.
Page 294: Ao Block Modes

™ FOUNDATION fieldbus function blocks • PV_SCALE: PV_SCALE is used to convert the FF value in SP to percent. The units are usually percent. • XD_SCALE: XD_SCALE is used to convert the percent FF value to the value for the channel, which should be given in the device manual.
Page 295: Ao Block Simulation

™ FOUNDATION fieldbus function blocks C.2.4 AO block simulation When simulation is enabled, the last value of OUT is maintained and reflected in the field value of the SIMULATE attribute. In this case, the PV and READBACK values and statuses are based on the SIMULATE value and the status that you enter.
Page 296: Integrator (Int) Function Block

™ FOUNDATION fieldbus function blocks Integrator (INT) Function Block The Integrator (INT) function block integrates one or two variables over time. The block compares the integrated or accumulated value to pre-trip and trip limits and generates discrete output signals when the limits are reached. The INT integrates one process value.
Page 297: Int Block Configuration Parameters

™ FOUNDATION fieldbus function blocks This block is intended to have measurements that come from a process calculation path. It will work with input from a control path. The block output starts a process calculation path. The block is unusual because the status of the output has to be calculated. The output status is not directly related to the status of the inputs.
Page 298: Int Block Other Parameters

If the Confirm reset is set, the block shall not process subsequent re- set at RESET_IN until RESET_CONFIRM discrete input is TRUE. Input 1 pass through This is special option only used for Emerson Integrator block to pass internal totals to Integrator block. •…
Page 299: Int Block Modes

™ FOUNDATION fieldbus function blocks • SRTOTAL: The read-only snapshot of RTOTAL just before a reset. Same units as OUT. • N_RESET: Counts the number of resets. It can not be written or reset. C.3.3 INT block modes The Integrator function block supports the following modes: •…
Page 300: Int Block Special Mode

™ FOUNDATION fieldbus function blocks C.3.6 INT block special mode Enhanced FF host Overview > Totalizer Control > Configure Integrator Block Fieldbus Host Measurement TB > INTEGRATOR_FB_CONFIG (OD Index 50) Along with standard operation of integrating the process value at INn, the Micro Motion Integrator function block has one special mode of operation: Input 1 pass through.
Page 301: Int Block Default Configuration

™ FOUNDATION fieldbus function blocks Fieldbus code Label Description Internal ED: Net Block outputs internal ED: net mass total value and RESET_IN re- Mass Total sets internal ED: net mass total Internal ED: Net Block outputs internal ED: net mass inventory value and RESET_IN Mass Inventory resets internal ED: net mass inventory Internal ED: Net…
Page 302: Di Block Modes

™ FOUNDATION fieldbus function blocks Channel Description Zero in progress Analog output fault Meter verification failed • IO_OPTS: allows the option to have the value of FIELD_VAL_D be logically inverted before becoming the PV_D, if the “Invert” option is selected. •…
Page 303: Di Block Default Configuration

™ FOUNDATION fieldbus function blocks C.4.6 DI block default configuration DI1 (DI_4400_xxxx) CHANNEL Analog Output Fault (33) IO_OPTS 0x0000 STATUS_OPTS 0x0000 Discrete Output (DO) function block The Discrete Output (DO) function block processes a discrete setpoint and saves it to a specified channel to produce an output signal.
Page 304: Do Block Modes

™ FOUNDATION fieldbus function blocks • IO_OPTS: Options which the user may select to alter input and output block processing. Invert — Causes the SP_D value to be inverted before it becomes the output. May be used for normally open solenoid valves and other inverted actuators. SP-PV Track in Man — The value of SP is set to the value of PV when the target mode is Man.
Page 305: Do Block Errors

™ FOUNDATION fieldbus function blocks C.5.3 DO block errors The following conditions are reported in the BLOCK_ERR attribute: • Simulate Active: SIMULATE_D is enabled; therefore, PV_D is not real. • Input failure/process variable has Bad status: The readback value is bad. •…
Page 306
™ FOUNDATION fieldbus function blocks Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 307: Appendix D Using The Transmitter Display

Using the transmitter display Appendix D Using the transmitter display Using the display D.1.1 Components of the transmitter interface The transmitter interface includes the status LED, the display (LCD panel), and two optical switches. Figure D-1: Transmitter interface Status LED Display (LCD panel) Process variable Scroll optical switch…
Page 308: Use The Optical Switches

Using the transmitter display Note Display refers to the display on the remotely mounted transmitter, not directly mounted to the meter. If there is a display directly on the meter, it can only view process variables, and it cannot be used for any other operation.
Page 309
Using the transmitter display Prerequisites To access the display menu system, operator access to either the Off-Line menu or the Alert menu must be enabled. To access the complete menu system, operator access must be enabled for both the Off-Line menu and the Alert menu. Procedure At the transmitter display, activate theScroll and Select optical switches simultaneously until the display changes.
Page 310
Using the transmitter display • Exit each menu separately, working your way back to the top of the menu system. • Wait until the display times out and returns to displaying process variable data. Enter a floating-point value using the display Certain configuration values (for example, Lower Range Value and Upper Range Value) are entered as floating-point values.
Page 311
Using the transmitter display If the current value is positive and there is a blank space at the left of the value, activate Select until the cursor is flashing under the blank space, then activate Scroll until the minus sign appears. If the current value is positive and there is no blank space at the left of the value, activate Select until the cursor is flashing under the leftmost digit, then activate Scroll until the minus sign appears.
Page 312
Using the transmitter display • S = Sign. A minus sign (−) indicates a negative number. A blank indicates a positive number. • X.XXX = The 4-digit mantissa. • E = The exponent indicator. • YY = The 2-digit exponent. Procedure Switch from decimal notation to exponential notation.
Page 313: Display Codes For Process Variables

Using the transmitter display To save the displayed value to transmitter memory, activate Scroll and Select simultaneously and hold until the display changes. • If the displayed value is the same as the value in transmitter memory, you will be returned to the previous screen.
Page 314: Codes And Abbreviations Used In Display Menus

Using the transmitter display Table D-2: Display codes for process variables (continued) Code Definition Comment or reference STD V Standard volume flow rate Concentration measurement application only STDVI Standard volume inventory Concentration measurement application only TCDENS Temperature-corrected density Petroleum measurement application only TCORI Temperature-corrected inventory Petroleum measurement application only…
Page 315
Using the transmitter display Table D-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference CUSTODY XFER Custody transfer DENS Density D EV Discrete event Events configured using the enhanced event model DGAIN, DRIVE % Drive gain DISBL Disable…
Page 316
Using the transmitter display Table D-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference INTERN Internal Input/output LANG Language LOCK Write-protect LOOP CUR Loop current M_ASC Modbus ASCII M_RTU Modbus RTU MAO1 mA Output 1 (primary mA Output) MAO2…
Page 317
Using the transmitter display Table D-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference WRPRO Write protect PVR applications only XMTR Transmitter Configuration and Use Manual…
Page 318
Using the transmitter display Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 319: Appendix E Using Prolink Iii With The Transmitter

In most ProLink III installations, the manual is installed with the ProLink III program. Additionally, the ProLink III manual is available on the documentation CD or at www.emerson.com. ProLink III features and functions ProLink III offers complete transmitter configuration and operation functions. ProLink III also offers a number of additional features and functions, including: •…
Page 320
Using ProLink III with the transmitter ProLink III messages As you use ProLink III with a Micro Motion transmitter, you will see a number of messages and notes. This manual does not document all of these messages and notes. Important The user is responsible for responding to messages and notes and complying with all safety messages.
Page 321: Appendix F Using A Field Communicator With The Transmitter

If you are unable to perform these tasks, consult the Field Communicator manual before attempting to use the Field Communicator. The Field Communicator manual is available on the documentation CD or at www.emerson.com. Field Communicator menus and messages Many of the menus in this manual start with the On-Line menu. Ensure that you are able to navigate to the On-Line menu.
Page 322: Connect With The Ff Host

Using a Field Communicator with the transmitter Connect with the FF host A connection from the FOUNDATION Fieldbus host to your transmitter allows you to read process data, configure the transmitter, and perform maintenance and troubleshooting tasks. Procedure Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 323: Appendix G Default Values And Ranges

Default values and ranges Appendix G Default values and ranges Default values and ranges The default values and ranges represent the typical factory transmitter configuration. Depending on how the transmitter was ordered, certain values may have been configured at the factory and are not represented in the default values and ranges. Table G-1: Transmitter default values and ranges Type…
Page 324
Default values and ranges Table G-1: Transmitter default values and ranges (continued) Type Parameter Default Range Comments Density units g/cm Density cutoff 0.2 g/cm 0.0 – 0.5 g/cm 0 g/cm 1 g/cm 1000 µsec 1000 – 50,000 µsec 50,000 µsec 1000 –…
Page 325
Default values and ranges Table G-1: Transmitter default values and ranges (continued) Type Parameter Default Range Comments External pressure 0.000 psi Mass flow rate 200.000 g/s Volume flow rate 0.200 L/s Density 10.000 g/cm Temperature 450.000 °C Drive gain 100.000% Gas standard volume flow rate 423.78 SCFM External temperature…
Page 326
Default values and ranges Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 327: Appendix H Transmitter Components And Installation Wiring

Transmitter components and installation wiring Appendix H Transmitter components and installation wiring Topics covered in this appendix: • Installation types • Power supply terminals and ground • Fieldbus wiring terminals Installation types The transmitter was ordered and shipped to be installed in one of several possible configurations.
Page 328
Transmitter components and installation wiring Figure H-2: High-temperature meters with factory connection The transmitter is shipped with a flexible connection factory installed between the sensor and the transmitter. The transmitter must be dismounted from its shipping location (spot‐welded to the sensor case) and then mounted separately.
Page 329
Transmitter components and installation wiring Figure H-4: 4-wire remote installation for density and viscosity meters (CDM, FDM, or FVM with fieldbus only) The transmitter is installed remotely from the Compact Density Meter (CDM), Fork Density Meter (FDM), or Fork Viscosity Meter (FVM). The 4‐wire connection between the sensor and transmitter must be field wired. Power supply must be field wired to the transmitter.
Page 330
Transmitter components and installation wiring Figure H-5: 9-wire remote installation The transmitter and core processor are combined in a single unit that is installed remotely from the sensor. The 9‐wire connection between the transmitter/core processor and the sensor must be field wired. Power supply must be field wired to the transmitter.
Page 331
Transmitter components and installation wiring Figure H-6: Remote core processor with remote sensor installation The transmitter, core processor, and sensor are all mounted separately. The 4‐wire connection between the transmitter and core processor must be field wired. The 9‐wire connection between the core processor and the sensor must be field wired.
Page 332: Power Supply Terminals And Ground

Transmitter components and installation wiring Power supply terminals and ground Figure H-7: Power supply wiring terminals Warning flap Equipment ground Power supply wiring terminals (9 and 10) Fieldbus wiring terminals FOUNDATION Fieldbus Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 333: Appendix Ine53 History

NE53 history Appendix I NE53 history This document can be found at www.emerson.com. Operating instructions within this document are English versions. Instructions in other languages have different part numbers but matching revision letters. Operating Date Version Type Change instruction 09/2000…
Page 334
NE53 history Operating Date Version Type Change instruction Expansion • Software version information available either through the display or through Modbus • Totalizers can be disabled, in addition to starting and stopping • Doubled the number of virtual communication rela- tionshups (VCRs) Adjustment •…
Page 335
NE53 history Operating Date Version Type Change instruction 07/2012 Adjustment • Added DI channels to increment the Concentration 3600326 EB Mass Curve • Added Special units support for both Mass Flow and Volume Flow • Moved mass flow, volume flow, and density limit pa- rameters from the Device Info TB to the Measurement •…
Page 336
NE53 history Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 337
NE53 history Configuration and Use Manual…
Page 338
© 2018 Micro Motion, Inc. All rights reserved. The Emerson logo is a trademark and service mark of Emerson Electric Co. Micro Motion, ELITE, ProLink, MVD and MVD Direct Connect marks are marks of one of the Emerson Automation Solutions family of companies. All other marks are property of their respective owners.

Источник

Contents
Table of Contents
Troubleshooting
Bookmarks

Related Manuals for Emerson Micro Motion 2700

Summary of Contents for Emerson Micro Motion 2700

Page 1
Configuration and Use Manual 20000326, Rev ED April 2018 ® Micro Motion Model 2700 Transmitters with ™ FOUNDATION Fieldbus Configuration and Use Manual…
Page 2
Micro Motion employees. Micro Motion will not accept your returned equipment if you fail to follow Micro Motion procedures. Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion Customer Service department.
Page 3: Table Of Contents

Contents Contents Part I Getting started Chapter 1 Before you begin ………………….3 About this manual ……………………3 Communication methods ………………….3 Additional documentation and resources ………………4 Chapter 2 Quick start ……………………5 Power up the transmitter ………………….5 Check meter status ……………………5 2.2.1 Transmitter status reported by LED …………….6 Determine the FOUNDATION Fieldbus unique device ID …………..7…
Page 4
Contents 4.5.2 Configure two-phase flow parameters ……………. 34 4.5.3 Configure Density Damping ………………35 4.5.4 Configure Density Cutoff ………………..36 Configure temperature measurement ………………37 4.6.1 Configure Temperature Measurement Unit …………..37 4.6.2 Configure Temperature Damping …………….38 4.6.3 Effect of Temperature Damping on process measurement ……… 39 Configure the petroleum measurement application …………..
Page 5
Contents Back up transmitter configuration ………………… 71 Return function blocks to In Service (Auto) mode …………..72 Part III Operations, maintenance, and troubleshooting Chapter 7 Transmitter operation ………………..75 Record the process variables ………………… 75 View process variables …………………..76 7.2.1 View process variables using the display …………..76 7.2.2 View process variables and other data using ProLink III ……….77…
Page 6
Contents Check the drive gain …………………… 122 9.9.1 Collect drive gain data ………………..123 9.10 Check the pickoff voltage ………………….123 9.10.1 Collect pickoff voltage data ………………124 9.11 Check for internal electrical problems ………………124 9.11.1 Check the sensor coils ………………..124 Appendices and reference Appendix A Transducer blocks and views ………………127…
Page 7
Contents A.8.3 Process variables for concentration measurement transducer blocks ……. 225 A.8.4 Totals for concentration measurement transducer blocks ……..226 A.8.5 Setup data for concentration measurement transducer blocks ……… 227 A.8.6 Other additions for concentration measurement transducer blocks ……232 Density viscosity meter transducer blocks …………….
Page 8
Contents Appendix D Using the transmitter display ………………299 Using the display ……………………299 D.1.1 Components of the transmitter interface …………..299 D.1.2 Use the optical switches ………………..300 D.1.3 Access and use the display menu system …………..300 D.1.4 Display codes for process variables …………….305 D.1.5 Codes and abbreviations used in display menus …………306 Appendix E…
Page 9: Getting Started

Getting started Part I Getting started Chapters covered in this part: • Before you begin • Quick start Configuration and Use Manual…
Page 10
Getting started Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 11: Before You Begin

Before you begin Before you begin Topics covered in this chapter: • About this manual • Communication methods • Additional documentation and resources About this manual This manual helps you configure, commission, use, maintain, and troubleshoot ™ Micro Motion Model 2700 transmitters with FOUNDATION fieldbus.
Page 12: Additional Documentation And Resources

Topic Document Hazardous area installa- See the approval documentation shipped with the transmitter, or tion download the appropriate documentation at www.emerson.com. ™ Product Data Sheet Micro Motion Series 1000 and Series 2000 Transmitters with MVD Tech‐ nology Product Data Sheet…
Page 13: Chapter 2 Quick Start

Quick start Quick start Topics covered in this chapter: • Power up the transmitter • Check meter status • Determine the FOUNDATION Fieldbus unique device ID • Make a startup connection to the transmitter • Verify mass flow measurement Power up the transmitter The transmitter must be powered up for all configuration and commissioning tasks, or for process measurement.
Page 14: Transmitter Status Reported By Led

Quick start Wait approximately 10 seconds for the power-up sequence to complete. Immediately after power-up, the transmitter runs through diagnostic routines and checks for error conditions. During the power-up sequence, Alert A009 is active. This alert should clear automatically when the power-up sequence is complete. Check the status LED on the transmitter.
Page 15: Determine The Foundation Fieldbus Unique Device Id

Quick start Determine the FOUNDATION Fieldbus unique device ID The transmitter is shipped with a sticker that displays a unique 32-digit number that the fieldbus segment uses for identification. If the sticker is missing, use this procedure to determine your device ID. From ProLink III, navigate to Device Tools >…
Page 16
Quick start Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 17: Part Ii Configuration And Commissioning

Configuration and commissioning Part II Configuration and commissioning Chapters covered in this part: • Introduction to configuration and commissioning • Configure process measurement • Configure device options and preferences • Complete the configuration Configuration and Use Manual…
Page 18
Configuration and commissioning Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 19: Introduction To Configuration And Commissioning

Introduction to configuration and commissioning Introduction to configuration and commissioning Topics covered in this chapter: • Configuration flowchart • Default values and ranges • Enable access to the off‐line menu of the display • Disable write‐protection on the transmitter configuration •…
Page 20
Introduction to configuration and commissioning Figure 3-1: Configuration flowchart Configure device options and preferences Test and move to production Configure process measurement Configure mass flow Test or tune transmitter Configure display measurement using sensor simulation parameters Configure volume flow meaurement Configure fault handling Back up transmitter parameters…
Page 21: Default Values And Ranges

Introduction to configuration and commissioning Default values and ranges Section G.1 to view the default values and ranges for the most commonly used parameters. Enable access to the off-line menu of the display Display OFF-LINE MAINT > OFF-LINE CONFG ProLink III Device Tools >…
Page 22: Place Function, Transducer, And Resource Blocks In Oos Mode

Introduction to configuration and commissioning Place function, transducer, and resource blocks in OOS mode Before you modify parameters on the fieldbus function, transducer, and resource blocks, you must place the blocks in Out of Service (OOS) mode. Before you return the device to operation, you must place them back in service (Auto mode).
Page 23: Restore The Factory Configuration

Introduction to configuration and commissioning Restore the factory configuration Display Not available ProLink III Device Tools > Configuration Transfer > Restore Factory Configuration Field Communicator Service Tools > Maintenance > Reset/Restore > Master Reset Fieldbus host Diagnostic TB > Restore Factory Config (OD Index 056) Overview Restoring the factory configuration returns the transmitter to a known operational configuration.
Page 24
Introduction to configuration and commissioning Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 25: Configure Process Measurement

Configure process measurement Configure process measurement Topics covered in this chapter: • Configure mass flow measurement • Configure volume flow measurement for liquid applications • Configure GSV flow measurement • Configure flow direction • Configure density measurement • Configure temperature measurement •…
Page 26
Configure process measurement Options for Mass Flow Measurement Unit The transmitter provides a standard set of measurement units for Mass Flow Measurement Unit, plus one user-defined special measurement unit. Different communications tools may use different labels for the units. Label Display ProLink III Field Communica-…
Page 27
Configure process measurement Define a special measurement unit for mass flow Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Special Units > Mass Special Units Fieldbus host Measurement TB >…
Page 28: Configure Flow Damping

Configure process measurement Example: Defining a special measurement unit for mass flow You want to measure mass flow in ounces per second (oz/sec). Set Base Mass Unit to Pounds (lb). Set Base Time Unit to Seconds (sec). Calculate Mass Flow Conversion Factor: a.
Page 29: Configure Mass Flow Cutoff

Configure process measurement • In general, lower damping values are preferable because there is less chance of data loss, and less lag time between the actual measurement and the reported value. The value you enter is automatically rounded off to the nearest valid value. For example, if the damping is currently set to 0.8 seconds, any value entered up to 1.2 seconds will be rounded down to 0.8 seconds, and any value entered from 1.21 to 1.59 seconds will be rounded up to 1.6 seconds.
Page 30: Configure Volume Flow Measurement For Liquid Applications

Configure process measurement Configure volume flow measurement for liquid applications The volume flow measurement parameters control how liquid volume flow is measured and reported. Restriction You cannot implement both liquid volume flow and gas standard volume flow at the same time. Choose one or the other.
Page 31
Configure process measurement Overview Volume Flow Measurement Unit specifies the unit of measurement that will be displayed for the volume flow rate. The unit used for the volume total and volume inventory is based on this unit. Prerequisites Before you configure Volume Flow Measurement Unit, be sure that Volume Flow Type is set to Liquid.
Page 32
Configure process measurement Label Unit description Display ProLink III Field Communicator l/hr Liters per hour Million liters per day MILL/D mil l/day ML/d UKGPS Imp gal/sec Impgal/s Imperial gallons per second UKGPM Imp gal/min Impgal/min Imperial gallons per minute UKGPH Imp gal/hr Impgal/h Imperial gallons per hour…
Page 33: Configure Volume Flow Cutoff

Configure process measurement The special unit label displays only on the local display. The AI block uses and displays the actual engineering unit (i.e. L/min). Procedure Specify Base Volume Unit. Base Volume Unit is the existing volume unit that the special unit will be based on. Specify Base Time Unit.
Page 34: Configure Gsv Flow Measurement

Configure process measurement Overview Volume Flow Cutoff specifies the lowest volume flow rate that will be reported as measured. All volume flow rates below this cutoff are reported as 0. Procedure Set Volume Flow Cutoff to the value you want to use. The default value for Volume Flow Cutoff is 0.0 l/sec (liters per second).
Page 35: Configure Standard Density Of Gas

Configure process measurement Procedure Set Volume Flow Type to Gas Standard Volume. 4.3.2 Configure Standard Density of Gas Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure > Manual Setup > Measurements > GSV > Gas Ref Density Fielbus host Measurement TB >…
Page 36
Configure process measurement The default setting for Gas Standard Volume Flow Unit is SCFM (Standard Cubic Feet per Minute). If the measurement unit you want to use is not available, you can define a special measurement unit. Options for Gas Standard Volume Flow Unit The transmitter provides a standard set of measurement units for Gas Standard Volume Flow Unit, plus one user-defined special measurement unit.
Page 37
Configure process measurement Define a special measurement unit for gas standard volume flow Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Special Units > Special GSV Units Fieldbus host Measurement TB >…
Page 38: Configure Gas Standard Volume Flow Cutoff

Configure process measurement The special measurement unit is stored in the transmitter. You can configure the transmitter to use the special measurement unit at any time. Example: Defining a special measurement unit for gas standard volume flow You want to measure gas standard volume flow in thousands of standard cubic feet per minute.
Page 39: Configure Flow Direction

Configure process measurement Configure flow direction Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow Field Communicator Configure > Manual Setup > Measurements > Flow > Flow Direction Fieldbus host Measurement TB > FLOW_DIRECTION {OD Index 41) Overview Flow Direction controls how forward flow and reverse flow affect flow measurement and reporting.
Page 40
Configure process measurement Flow Direction setting Relationship to Flow Direction arrow ProLink III Field Communicator on sensor Negate Forward Negate/Forward Only Appropriate when the Flow Direction ar- row is in the opposite direction from the majority of flow. Negate Bidirectional Negate/Bi-directional Appropriate when both forward and re- verse flow are expected, and reverse flow…
Page 41: Configure Density Measurement

Configure process measurement Configure density measurement The density measurement parameters control how density is measured and reported. 4.5.1 Configure Density Measurement Unit Display OFF-LINE MAINT > OFF-LINE CONFG > UNITS > DENS ProLink III Device Tools > Configuration > Process Measurement > Density Field Communicator Configure >…
Page 42: Configure Two-Phase Flow Parameters

Configure process measurement Label Unit description Display ProLink III Field Communicator D API degAPI degAPI Degrees API (1) Non‐standard calculation. This value represents line density divided by the density of water at 4 °C. 4.5.2 Configure two-phase flow parameters Display Not available ProLink III Device Tools >…
Page 43: Configure Density Damping

Configure process measurement You must enter Two-Phase Flow High Limit in g/cm³, even if you configured another unit for density measurement. Set Two-Phase Flow Timeout to the number of seconds that the transmitter will wait for a two-phase flow condition to clear before posting the alert. The default value for Two-Phase Flow Timeout is 0.0 seconds, meaning that the alert will be posted immediately.
Page 44: Configure Density Cutoff

Configure process measurement Damping is used to smooth out small, rapid fluctuations in process measurement. Damping Value specifies the time period (in seconds) over which the transmitter will spread changes in the process variable. At the end of the interval, the internal value will reflect 63% of the change in the actual measured value.
Page 45: Configure Temperature Measurement

Configure process measurement Overview Density Cutoff specifies the lowest density value that will be reported as measured. All density values below this cutoff will be reported as 0. Procedure Set Density Cutoff to the value you want to use. For most applications, the default setting (0.2 g/cm³) is sufficient. The range is 0.0 g/cm³ to 0.5 g/cm³.
Page 46: Configure Temperature Damping

Configure process measurement Label Field Communica- Unit description Display ProLink III °C °C degC Degrees Celsius Degrees Fahrenheit °F °F degF °R °R degR Degrees Rankine °K °K Kelvin 4.6.2 Configure Temperature Damping Display Not available ProLink III Device Tools > Configuration > Temperature Field Communicator Configure >…
Page 47: Effect Of Temperature Damping On Process Measurement

Configure process measurement • In general, lower damping values are preferable because there is less chance of data loss, and less lag time between the actual measurement and the reported value. The value you enter is automatically rounded off to the nearest valid value. Valid values for Temperature Damping are 0, 0.6, 1.2, 2.4, 4.8, ……
Page 48
Configure process measurement Prerequisites You will need API documentation for the API table that you select. Depending on your API table, you may need to know the thermal expansion coefficient (TEC) for your process fluid. You must know the reference temperature that you want to use. Procedure Choose Device Tools >…
Page 49: Configure Petroleum Measurement Using The Field Communicator

Configure process measurement b. Verify that the referred density range of the selected table is adequate for your application. If you chose a C table, enter Thermal Expansion Coefficient (TEC) for your process fluid. Set Reference Temperature to the temperature to which density will be corrected in referred density calculations.
Page 50
Configure process measurement Table name Process fluid CTL source data Reference temperature Density unit Generalized crude and Observed density and 60 °F (non-configurable) Degrees API observed temperature Range: 0 to 100 Generalized products Observed density and 60 °F (non-configurable) Degrees API observed temperature Range: 0 to 85 Lubricating oils…
Page 51: Set Up Concentration Measurement

Configure process measurement Set up concentration measurement This section guides you through loading and setting up a concentration matrix used for measurement. It does not cover building a concentration matrix. The concentration measurement application calculates concentration data from process temperature and density. Micro Motion provides a set of concentration matrices that provide the reference data for several standard industry applications and process fluids.
Page 52: Configure Concentration Measurement Using The Field Communicator

Configure process measurement • If you change the setting of Derived Variable, all existing concentration matrices will be deleted from transmitter memory. Set Derived Variable before loading concentration matrices. Load one or more matrices. a. Set Matrix Being Configured to the location to which the matrix will be loaded. b.
Page 53
Configure process measurement Choose Online > Configure > Manual Setup > Measurements > Temperature and set Temperature Unit to match the temperature unit used by your matrix. Choose Online > Configure > Manual Setup > Measurements and click Concentration Measurement. Set up extrapolation alerts.
Page 54: Standard Matrices For The Concentration Measurement Application

Configure process measurement Option Setup A value written by a. Choose Online > Configure > Manual Setup > Measurements > digital communica- External Inputs tions b. Enable External Temperature. c. Perform the necessary host programming and communications setup to write temperature data to the transmitter at appropri- ate intervals.
Page 55: Derived Variables And Calculated Process Variables

Configure process measurement Temperature Matrix name Description Density unit unit Derived variable HFCS 42 °C Mass Concentration Matrix represents a hydrometer scale g/cm (Density) for HFCS 42 (high-fructose corn syrup) solutions that indicates the percent by mass of HFCS in solution. HFCS 55 Matrix represents a hydrometer scale g/cm…
Page 56: Set Up Concentration Measurement Using A Basic Ff Host

Configure process measurement Calculated process variables Density at reference Standard Derived tempera- volume Specific Concen- Net mass volume Variable Description ture flow rate gravity tration flow rate flow rate ✓ ✓ ✓ ✓ ✓ Mass The percent mass of Concentration solute or of material in (Specific Gravity) suspension in the total…
Page 57: Set Reference Temperature Values For Specific Gravity Using A Basic Ff Host

Configure process measurement 4.9.1 Set reference temperature values for specific gravity using a basic FF host When Derived Variable is set to any option based on specific gravity, you must set the reference temperature for water, then verify the density of water at the configured reference temperature.
Page 58: Modify Extrapolation Alerts For Concentration Measurement Using A Basic Ff Host

Configure process measurement Table 4-3: Concentration unit codes Fieldbus code Unit 1110 degTwad 1426 degBrix 1111 degBaum hv 1112 degBaum It 1343 % sol/wt 1344 % sol/vol 1427 degBall 1428 proof/vol 1429 proof/mass 1346 % plato special Write a value into the Special Concentration Unit Label parameter if Concentration Unit is set to code 253 (special).
Page 59: Select The Active Concentration Matrix Using A Basic Ff Host

Not all sensors or applications require pressure compensation. The pressure effect for a specific sensor model can be found in the product data sheet located at www.emerson.com. If you are uncertain about implementing pressure compensation, contact customer service. Prerequisites You will need the flow factor, density factor, and calibration pressure values for your sensor.
Page 60: Configure Pressure Compensation Using Prolink Iii

Configure process measurement • For the calibration pressure, see the calibration sheet for your sensor. If the data is unavailable, use 20 PSI. 4.10.1 Configure pressure compensation using ProLink III Choose Device Tools > Configuration > Process Measurement > Pressure Compensation.
Page 61: Options For Pressure Measurement Unit

Configure process measurement The flow factor is the percent change in the flow rate per PSI. When entering the value, reverse the sign. Example: If the flow factor is 0.000004 % per PSI, enter −0.000004 % per PSI. Enter Dens Press Factor for your sensor. The density factor is the change in fluid density, in g/cm /PSI.
Page 62
Configure process measurement Label Unit description Display ProLink III Field Communicator mmH2O mm Water @ 68°F mmH2O (68°F) Millimeters water @ 68 °F Millimeters mercury @ 0 °C mmHG mm Mercury @ 0°C mmHg (0°C) INHG In Mercury @ 0°C inHg (0°C) Inches mercury @ 0 °C Pounds per square inch…
Page 63: Configure Device Options And Preferences

Configure device options and preferences Configure device options and preferences Topics covered in this chapter: • Configure the transmitter display • Enable or disable operator actions from the display • Configure security for the display menus • Configure response time parameters •…
Page 64: Configure The Process Variables And Diagnostic Variables Shown On The Display

Configure device options and preferences 5.1.2 Configure the process variables and diagnostic variables shown on the display Display Not available ProLink III Device Tools > Configuration > Transmitter Display > Display Variables Field Communicator Configure > Manual Setup > Display > Display Variables Fieldbus host LDO TB >…
Page 65: Configure The Number Of Decimal Places (Precision) Shown On The Display

Configure device options and preferences Display variable Process variable assignment Display Variable 12 None Display Variable 13 None Display Variable 14 None Display Variable 15 None 5.1.3 Configure the number of decimal places (precision) shown on the display Display Not available ProLink III Device Tools >…
Page 66: Configure The Refresh Rate Of Data Shown On The Display

Configure device options and preferences 5.1.4 Configure the refresh rate of data shown on the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > RATE ProLink III Device Tools > Configuration > Transmitter Display > Display Variables Field Communicator Configure > Manual Setup > Display > Display Variable Menu Features > Refresh Rate Fieldbus host LDO TB >…
Page 67: Enable Or Disable The Display Backlight

Configure device options and preferences If you enabled Auto Scroll, set Scroll Rate as desired. The default value is 10 seconds. Scroll Rate may not be available until you apply Auto Scroll. 5.1.6 Enable or disable the display backlight Display OFF-LINE MAINT >…
Page 68: Enable Or Disable Operator Actions From The Display

Configure device options and preferences Enable or disable operator actions from the display You can configure the transmitter to let the operator perform specific actions using the display. • Enable or disable Totalizer Start/Stop from the display (Section 5.2.1) • Enable or disable Totalizer Reset from the display (Section 5.2.2) •…
Page 69: Enable Or Disable Totalizer Reset From The Display

Configure device options and preferences 5.2.2 Enable or disable Totalizer Reset from the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > TOTALS RESET ProLink III Device Tools > Configuration > Totalizer Control Methods Field Communicator Configure > Manual Setup > Display > Display Variable Menu Features > Totalizer Reset Fieldbus host LDO TB >…
Page 70: Configure Security For The Display Menus

Configure device options and preferences Overview You can configure whether or not the operator can use a single command to acknowledge all alerts from the display. Procedure Ensure that the alert menu is accessible from the display. To acknowledge alerts from the display, operators must have access to the alert menu.
Page 71
Configure device options and preferences Option Description Enabled (default) Operator can access the alert menu. This access is required to view and acknowledge alerts, but is not required for Smart Meter Verification (if applicable), configuration, or calibration. Disabled Operator cannot access the alert menu. Note The transmitter status LED changes color to indicate that there are active alerts, but does not show specific alerts.
Page 72: Configure Response Time Parameters

Configure device options and preferences Configure response time parameters You can configure the rate at which process data is polled and process variables are calculated. Configure alert handling The alert handling parameters control the transmitter’s response to process and device conditions.
Page 73: Configure Status Alert Severity

Configure device options and preferences 5.5.2 Configure Status Alert Severity Display Not available ProLink III Device Tools > Configuration > Alert Severity Field Communicator Configure > Alert Setup > Alert Severity > Set Alert Severity Fieldbus host Diag TB > ALARM_INDEX (OD Index 23) Diag TB >…
Page 74
Configure device options and preferences Status alerts and options for Status Alert Severity Table 5-1: Status alerts and Status Alert Severity Alert code Status message Default severity Notes Configurable? A001 EEPROM Error (Core Pro- Fault cessor) RAM Error (Core Processor) Fault A002 Fault A003…
Page 75: Configure Informational Parameters

Configure device options and preferences Table 5-1: Status alerts and Status Alert Severity (continued) Alert code Status message Default severity Notes Configurable? Meter Verification Aborted Fault A035 Applies only to transmitters with Smart Meter Verification. A102 Drive Overrange Informational A104 Calibration in Progress Informational Can be set to either Informational or…
Page 76: Configure Sensor Serial Number

Configure device options and preferences 5.6.1 Configure Sensor Serial Number Display Not available ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information > Sensor Serial Num- Fieldbus host Device Info TB >…
Page 77: Configure Sensor Liner Material

Configure device options and preferences 5.6.3 Configure Sensor Liner Material Display Not available ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information > Tube Lining Fieldbus host Device Info TB >…
Page 78: Configure Descriptor

Configure device options and preferences 5.6.5 Configure Descriptor Display Not available ProLink III Device Tools > Configuration > Informational Parameters > Transmitter Field Communicator Configure > Manual Setup > Info Parameters > Transmitter Info > Descriptor Fieldbus host Device Info TB > DESCRIPTION (OD Index 19) Overview Descriptor lets you store a description in transmitter memory.
Page 79: Complete The Configuration

Complete the configuration Complete the configuration Topics covered in this chapter: • Back up transmitter configuration • Return function blocks to In Service (Auto) mode Back up transmitter configuration ProLink III provides a configuration upload/download function which allows you to save configuration sets to your PC.
Page 80: Return Function Blocks To In Service (Auto) Mode

Complete the configuration Return function blocks to In Service (Auto) mode Display Not available ProLink III Not available Field Communicator Overview > Mode Fieldbus host All TBs > MODE_BLOCK (OD Index Number 005) Overview After modifying function block parameters, the fieldbus function blocks must be placed in service (Auto) mode before you return the device to operation.
Page 81: Part Iii Operations, Maintenance, And Troubleshooting

Operations, maintenance, and troubleshooting Part III Operations, maintenance, and troubleshooting Chapters covered in this part: • Transmitter operation • Measurement support • Troubleshooting Configuration and Use Manual…
Page 82
Operations, maintenance, and troubleshooting Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 83: Chapter 7 Transmitter Operation

Reset inventories Record the process variables Emerson suggests that you make a record of specific process variable measurements, including the acceptable range of measurements, under normal operating conditions. This data will help you recognize when the process or diagnostic variables are unusually high or low, and may help you diagnose and troubleshoot application issues.
Page 84: View Process Variables

Transmitter operation View process variables Display Scroll to the desired process variable. If AutoScroll is enabled, you can wait until the process variable is displayed. See Section 7.2.1 for more information. ProLink III View the desired variable on the main screen under Process Variables. See Section 7.2.2 for more information.
Page 85: View Process Variables And Other Data Using Prolink Iii

Transmitter operation Figure 7-1: Transmitter display features A. Status LED B. Display (LCD panel) C. Process variable D. Scroll optical switch E. Optical switch indicator: turns red when either Scroll or Select is activated F. Select optical switch G. Unit of measure for process variable H.
Page 86: View Transmitter Status Using The Status Led

Transmitter operation • To view a more complete set of process variables, plus the current state of the outputs, choose Service Tools > Variables. View transmitter status using the status LED The status LED shows the current alert condition of the transmitter. The status LED is located on the face of the transmitter.
Page 87: View And Acknowledge Status Alerts

Transmitter operation Table 7-1: Transmitter status reported by status LED (continued) LED state Description Recommendation Flashing red (if ena- One or more high-severity alerts are active A high-severity alert condition affects meas- bled) and have not been acknowledged. urement accuracy and output behavior. Re- solve the alert condition before continuing.
Page 88
Transmitter operation Figure 7-2: Using the display to view and acknowledge the status alerts Scroll and Select simultaneously for 4 seconds SEE ALARM Select Is ACK ALL enabled? ACK ALL Select Scroll EXIT Select Scroll Active/ unacknowledged alarms? Alarm code NO ALARM Scroll Select…
Page 89: View And Acknowledge Alerts Using Prolink Iii

Transmitter operation Postrequisites • To clear the following alerts, you must correct the problem, acknowledge the alert, then power-cycle the transmitter: A001, A002, A010, A011, A012, A013, A018, A019, A022, A023, A024, A025, A028, A029, A031. • For all other alerts: If the alert is inactive when it is acknowledged, it will be removed from the list.
Page 90: View Alerts Using The Field Communicator

Transmitter operation If the alert is active when it is acknowledged, it will be removed from the list when the alert condition clears. Related information Alert data in transmitter memory 7.4.3 View alerts using the Field Communicator You can view a list containing all alerts that are active, or inactive but unacknowledged. •…
Page 91: Alert Data In Transmitter Memory

Transmitter operation 7.4.5 Alert data in transmitter memory The transmitter maintains three sets of data for every alert that is posted. For each alert occurrence, the following three sets of data are maintained in transmitter memory: • Alert List • Alert Statistics •…
Page 92: Start And Stop Totalizers And Inventories

Transmitter operation Start and stop totalizers and inventories Display Section 7.6.1. ProLink III Device Tools > Totalizer Control > Totalizer and Inventories > Start All Totals Device Tools > Totalizer Control > Totalizer and Inventories > Stop All Totals Field Communicator Service Tools > Variables > Totalizer Control > All Totalizers > Start Totalizers Service Tools >…
Page 93: Reset Totalizers

Transmitter operation Exit displays beneath the current totalizer value. 4. Select. 5. Select again to confirm. 6. Scroll to EXIT. • To stop all totalizers and inventories using the display: 1. Scroll until the word TOTAL appears in the lower left corner of the display. Important Because all totalizers are started or stopped together, it does not matter which total you use.
Page 94: Reset Totalizers Using The Display

Transmitter operation 7.7.1 Reset totalizers using the display Prerequisites • The Totalizer Reset display function must be enabled. • The totalizer that you want to reset must be configured as a display variable. For example: If you want to reset the mass totalizer, Mass Total must be configured as a display variable.
Page 95: Reset Inventories

Transmitter operation Exit displays beneath the current totalizer value. 3. Scroll until Reset displays beneath the current totalizer value. 4. Select. Reset and Yes? alternately flash beneath the current totalizer value. 5. Select again to confirm. 6. Scroll to EXIT. 7.
Page 96
Transmitter operation Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 97: Chapter 8 Measurement Support

Measurement support Measurement support Topics covered in this chapter: • Options for measurement support • Use Smart Meter Verification (SMV) • Zero the meter • Validate the meter • Perform a (standard) D1 and D2 density calibration • Perform temperature calibration Options for measurement support Micro Motion provides several measurement support procedures to help you evaluate and maintain your flowmeter’s accuracy.
Page 98: Smv Requirements

Measurement support 8.2.1 SMV requirements To use SMV, the transmitter must be paired with an enhanced core processor. Table 8‐1 for the minimum version of the transmitter, enhanced core processor, and communication tool needed to support SMV. (If you are going to perform SMV using the display, only the transmitter and enhanced core processor versions apply.) Table 8-1: Minimum SMV version…
Page 99: Run Smv

Measurement support SMV has an output mode called Continuous Measurement that allows the transmitter to keep measuring while the test is in progress. If you choose to run the test in Last Measured Value or Fault modes instead, the transmitter outputs will be held constant for the two minute duration of the test.
Page 100
Measurement support Option Description Last Value During the test, all outputs will report the last measured value of their as- signed process variable. The test will run for approximately 140 seconds. While the test is in progress, dots traverse the display and test progress is shown. Postrequisites View the test results and take any appropriate actions.
Page 101
Measurement support Enter any desired information on the Test Definition screen, and click Next. All information on this screen is optional. Choose the desired output behavior. Option Description Continue Measur- During the test, all outputs will continue to report their assigned process variable.
Page 102: View Test Data

Measurement support 8.2.4 View test data You can view the results of the current test. You can also view results from previous tests. Important You can view previous test results and see detailed test reports only if SMV is licensed. The transmitter stores the following information about the previous twenty SMV tests: •…
Page 103
Measurement support b. Scroll to Results Read and press Select. The runcount of the most recent test is displayed. c. To view data for this test, press Select, then press Scroll to scroll through test data. d. To select a different test, press Scroll, then press Select when the transmitter displays Results More?.
Page 104
Measurement support View test result data using ProLink III Prerequisites You can view test result data only if your SMV is licensed and only for tests that were run on the PC you are currently using. Procedure Choose Device Tools > Diagnostics > Meter Verification and click Previous Test Results.
Page 105: Schedule Automatic Execution Of The Smv Test

Measurement support • If the meter passes the second test, the first result can be ignored. • If the meter fails the second test, the flow tubes may be damaged. Call customer support. Abort A problem occurred with the meter verification test (such as process instability) or you stopped the test manually.
Page 106
Measurement support Figure 8-5: SMV – Top-level menu Scroll and Select simultaneously for 4 seconds Scroll ENTER METER VERFY Select RUN VERFY RESULTS READ SCHEDULE VERFY EXIT Scroll Scroll Scroll Select Select Select Scroll Select Scroll to Schedule Verfy and press Select. To schedule a single test or the first test in recurring execution: a.
Page 107
Measurement support SMV flowchart: Scheduling test execution using the display Figure 8-6: Scheduling SMV test execution using the display SCHEDULE VERFY Select Schedule set? SCHED IS OFF TURN OFF SCHED/YES? Scroll Scroll Select Schedule deleted HOURS LEFT Scroll Select xx HOURS Select SET NEXT SET RECUR…
Page 108: Zero The Meter

Measurement support To schedule recurring execution, specify a value for Hours Between Recurring Runs. To disable scheduled execution: • To disable execution of a single scheduled test, set Hours Until Next Run to 0. • To disable recurring execution, set Hours Between Recurring Runs to 0. •…
Page 109: Validate The Meter

Measurement support If necessary, modify Zero Time. Zero Time controls the amount of time the transmitter takes to determine its zero-flow reference point. The default Zero Time is 20 seconds. For most applications, the default Zero Time is appropriate. Postrequisites Restore normal flow through the sensor by opening the valves.
Page 110
Measurement support If you plan to calculate the meter factor for volume flow, be aware that validating volume in the field may be expensive, and the procedure may be hazardous for some process fluids. Therefore, because volume is inversely proportional to density, an alternative to direct measurement is to calculate the meter factor for volume flow from the meter factor for density.
Page 111: Alternate Method For Calculating The Meter Factor For Volume Flow

Measurement support 8.4.1 Alternate method for calculating the meter factor for volume flow The alternate method for calculating the meter factor for volume flow is used to avoid the difficulties that may be associated with the standard method. This alternate method is based on the fact that volume is inversely proportional to density. It provides partial correction of the volume flow measurement by adjusting for the portion of the total offset that is caused by the density measurement offset.
Page 112: Perform A D1 And D2 Density Calibration Using Prolink Iii

Measurement support Prerequisites • During density calibration, the sensor must be completely filled with the calibration fluid, and flow through the sensor must be at the lowest rate allowed by your application. This is usually accomplished by closing the shutoff valve downstream from the sensor, then filling the sensor with the appropriate fluid.
Page 113: Perform A D1 And D2 Density Calibration Using An Enhanced Ff Host

Measurement support Postrequisites If you disabled LD Optimization before the calibration procedure, re-enable it. 8.5.2 Perform a D1 and D2 density calibration using an enhanced FF host Read the Prerequistes on page 104 if you have not already done so. See the following figure.
Page 114: Perform Temperature Calibration

Measurement support Perform temperature calibration Temperature calibration establishes the relationship between the temperature of the calibration fluids and the signal produced by the sensor. Prerequisites The temperature calibration is a two-part procedure: temperature offset calibration and temperature slope calibration. The two parts must be performed without interruption, in the order shown.
Page 115: Perform Temperature Calibration Using A Fieldbus Host

Measurement support Important Consult customer support before performing a temperature calibration. Under normal circumstances, the temperature circuit is stable and should not need an adjustment. 8.6.1 Perform temperature calibration using a fieldbus host Write the temperature units to be used for calibration to Calibration TB > CAL_TEMPERATURE_UNITS (OD Index 56).
Page 116
Measurement support Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 117: Chapter 9 Troubleshooting

Troubleshooting Troubleshooting Topics covered in this chapter: • Status alerts, causes, and recommendations • Flow measurement problems • Density measurement problems • Temperature measurement problems • Check power supply wiring • Check grounding • Check for radio frequency interference (RFI) •…
Page 118
Troubleshooting Alert num- Alert title Possible cause Recommended actions A004 Temperature Over- The RTD resistance is out of range • Check your process conditions against range for the sensor. The tube RTD resist- the values reported by the device. ance is out of range for the sensor. •…
Page 119
Troubleshooting Alert num- Alert title Possible cause Recommended actions A009 Transmitter Initializ- Transmitter is in power-up mode. • Allow the meter to complete its power- ing/Warming Up up sequence. The alert should clear au- tomatically. • If other alerts are present, resolve those alert conditions first.
Page 120
Troubleshooting Alert num- Alert title Possible cause Recommended actions A013 Zero Calibration There was too much process insta- • Remove or reduce sources of electro- Failed: Unstable bility during the calibration proce- mechanical noise (e.g., pumps, vibra- dure. tion, pipe stress), cycle power to the meter, then retry the procedure.
Page 121
Troubleshooting Alert num- Alert title Possible cause Recommended actions A021 Transmitter/Sensor/ The configured board type does not • Verify all of the characterization or cali- Software Mismatch match the physical board, or the bration parameters. See the sensor tag configured sensor type does not or the calibration sheet for your meter.
Page 122
Troubleshooting Alert num- Alert title Possible cause Recommended actions A031 Low Power The transmitter is not receiving • Check the wiring between the transmit- enough power. ter and the core processor, then cycle power to the meter. This alert will not clear until you cy- •…
Page 123
Troubleshooting Alert num- Alert title Possible cause Recommended actions A102 Drive Overrange The drive power (current/voltage) is • Check the drive gain and the pickoff at its maximum. voltage. • Check the wiring between the sensor and the transmitter. • Verify that internal wiring is secure and that there are no internal electrical problems.
Page 124: Flow Measurement Problems

Troubleshooting Alert num- Alert title Possible cause Recommended actions A131 Meter Verification in A meter verification test is in pro- • Allow the procedure to complete. Progress: Outputs to gress, with outputs set to Last Meas- Last Measured Value ured Value. A132 Sensor Simulation Sensor simulation is enabled.
Page 125
Troubleshooting Problem Possible causes Recommended actions Erratic non-zero flow • Leaking valve or seal • Verify that the sensor orientation is appro- rate at no-flow condi- • Two-phase flow priate for your application (refer to the tions • Plugged or coated sensor tube sensor installation manual).
Page 126: Density Measurement Problems

Troubleshooting Problem Possible causes Recommended actions Inaccurate flow rate • Wiring problem • Check the wiring between the sensor and or batch total • Inappropriate measurement unit the transmitter. • Incorrect flow calibration factor • Verify that the measurement units are con- •…
Page 127: Temperature Measurement Problems

Troubleshooting Problem Possible causes Recommended actions Unusually high densi- • Plugged or coated sensor tube • Ensure that all of the calibration parame- ty reading • Incorrect density calibration factors ters have been entered correctly. See the • Incorrect temperature measurement sensor tag or the calibration sheet for your •…
Page 128: Check Power Supply Wiring

Troubleshooting Check power supply wiring If the power supply wiring is damaged or improperly connected, the transmitter may not receive enough power to operate properly. Prerequisites • You will need the installation manual for your transmitter. • When using DC power, a minimum of 1.5 amps of startup current is required. •…
Page 129: Check Grounding

Troubleshooting Check grounding A sensor and the transmitter must be grounded. Prerequisites You will need an: • Installation manual for your sensor • Installation manual for your transmitter (remote-mount installations only) Procedure Refer to the sensor and transmitter installation manuals for grounding requirements and instructions.
Page 130: Check The Drive Gain

Troubleshooting Check the settings of Two-Phase Flow Low Limit, Two-Phase Flow High Limit, and Two-Phase Flow Timeout. You can reduce the occurrence of two-phase flow alerts by setting Two-Phase Flow Low Limit to a lower value, Two-Phase Flow High Limit to a higher value, or Two-Phase Flow Timeout to a higher value.
Page 131: Collect Drive Gain Data

Troubleshooting Table 9-1: Possible causes and recommended actions for excessive (saturated) drive gain (continued) Possible cause Recommended actions Vibrating element Ensure that the vibrating element is free to vibrate. not free to vibrate Erratic drive gain Table 9-2: Possible causes and recommended actions for erratic drive gain Possible cause Recommended actions Foreign material…
Page 132: Collect Pickoff Voltage Data

Troubleshooting Table 9-3: Possible causes and recommended actions for low pickoff voltage (continued) Possible cause Recommended actions The vibrating element is not vibrating • Check for plugging or deposition. • Ensure that the vibrating element is free to vi- brate (no mechanical binding). Moisture in the sensor electronics Eliminate the moisture in the sensor electronics.
Page 133
Troubleshooting Procedure Disconnect power to the transmitter. DANGER! If the transmitter is in a hazardous area, wait 5 minutes before continuing. Unplug the terminal blocks from the terminal board on the core processor. Using a digital multimeter (DMM), check the pickoff coils by placing the DMM leads on the unplugged terminal blocks for each terminal pair.
Page 134
Troubleshooting With the DMM set to its highest range, there should be infinite resistance on each lead. If there is any resistance at all, there is a short to case. Test the resistance of junction box terminal pairs. a. Test the brown terminal against all other terminals except the red one. b.
Page 135: Appendix A Transducer Blocks And Views

Transducer blocks and views Appendix A Transducer blocks and views Topics covered in this appendix: • Descriptions of transducer block table entries • Measurement transducer blocks • Calibration transducer blocks • Diagnostics transducer blocks • Device information transducer blocks • Local display transducer blocks •…
Page 136: Descriptions Of Transducer Block Table Entries

Transducer blocks and views Descriptions of transducer block table entries Use the following definitions for the transducer block details tables: Index of the FOUNDATION Fieldbus parameter in the object dictionary Name Name of the fieldbus parameter used in the code Description Provides a description of the parameter.
Page 137: Measurement Transducer Blocks

Transducer blocks and views Table A-2: Access (continued) RW (Auto) Read/write, with the transducer block in Auto mode List of values The list of valid values to write to an enumerated parameter. This field is not applicable for read only parameters. Valid value ranges for variable type parameters are specified in the tables.
Page 138
Transducer blocks and views Table A-3: Measurement transducer block parameters view list (continued) View Index Name ST_REV TAG_DESC — — — — STRATEGY — — — ALERT_KEY — — — MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — —…
Page 139
Transducer blocks and views Table A-3: Measurement transducer block parameters view list (continued) View Index Name MFLOW_M_FACTOR — — — DENSITY_M_FACTOR — — — VOL_M_FACTOR — — — MASS_LOW_CUT — — — VOLUME_FLOW_LOW_CUTOFF — — — DENSITY_LOW_CUTOFF — — — FLOW_DIRECTION —…
Page 140: Standard Fieldbus Parameters For Measurement Transducer Blocks

Transducer blocks and views Table A-3: Measurement transducer block parameters view list (continued) View Index Name SNS_GSVflowBaseUnit — — — SNS_GSVflowBaseTime — — — SNS_GSVflowFactor — — — SNS_GSVflowText — — — SNS_GSVtotText — — — SNS_GSV_FlowCutoff — — — SNS_ResetGSVolTotal —…
Page 141
Transducer blocks and views Index and name Description List of values The user description of the intended block Any 32 characters application. TAG_DESC Msg type = STR Data type = OCTET STRING (32) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 Used to identify grouping of blocks.
Page 142
Transducer blocks and views Index and name Description List of values Occurs when a static parameter is changed — while a block mode is not in out of service UPDATE_EVT (OOS) mode, or when the mode changes from OOS mode and one or more static pa- rameters changed while the block was OOS.
Page 143: Process Variables For Measurement Transducer Blocks

Transducer blocks and views Index and name Description List of values Used for all config, H/W, connection failure 0 = No Error of system problems in the block. 18 = Calibration Error XD_ERROR 19 = Configuration Error Msg type = VAR 20 = Electronics Failure Data type = Unsigned8 (1) 21 = Sensor Failure…
Page 144
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Base mass unit 1089 = g 1088 = kg MFLOW_SPECIAL_UNIT_ Msg type = ENUM 1092 = t BASE Data type = Unsigned16 (2) 1094 = lb Store = Static 1095 = STon…
Page 145
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Density unit 1097 = kg/m3 1100 = g/cm3 DENSITY_UNITS Msg type = ENUM 1103 = kg/L Data type = Unsigned16 (2) 1104 = g/ml Store = Static 1105 = g/L…
Page 146
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Standard or special volume flow 1347 = m3/s rate unit 1348 = m 3/min VOLUME_FLOW_UNITS 1349 = m3/h CDM (2.0 and Msg type = ENUM 1350 = m3/d above)
Page 147
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Special volume unit conversion fac- — VOL_SPECIAL_UNIT_CONV Msg type = VAR Data type = FLOAT (4) Store = Static Access = RW (OOS) Available in Release 1.0 Special volume unit string Any 8 characters…
Page 148
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Density internal damping in sec- — onds DENSITY_DAMPING Msg type = VAR Data type = FLOAT (4) Store = Static Access = RW (OOS) Available in Release 1.0 Mass rate factor…
Page 149
Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Flow direction 0 = Forward Only 1 = Reverse Only FLOW_DIRECTION Msg type = ENUM 2 = Bi-Directional Data type = Unsigned16 (2) 3 = Absolute Value Store = Static 4 = Negate/Forward Only…
Page 150: Totalizers For Measurement Transducer Blocks

Transducer blocks and views Table A-4: Process variables for measurement transducer blocks (continued) Index and name Description List of values Low density limit of sensor in g/cc — LOW_DENSITY_LIMIT Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 1.0 Low volume flow limit of sensor…
Page 151
Transducer blocks and views Table A-5: Totalizers for measurement transducer blocks (continued) Index and name Description List of values Reset all totals Value part of DS-66 1 = Reset RESET_TOTALS Msg type = VAR Data type = DS-66 (2) Store = — Access = R/W in any mode Available in Release 1.0 Reset all inventories…
Page 152: Gas Process Variables For Measurement Tranducer Blocks

Transducer blocks and views Table A-5: Totalizers for measurement transducer blocks (continued) Index and name Description List of values Volume inventory — VOLUME_INVENTORY Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 1.0 Standard or special mass total and 1089 = g mass inventory unit…
Page 153
Transducer blocks and views Table A-6: Gas process variables for measurement transducer blocks (continued) Index and name Description List of values Reference volume gas total (not — valid when petroleum measure- GSV_Vol_Tot ment or concentration measure- ment is enabled) Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only…
Page 154
Transducer blocks and views Table A-6: Gas process variables for measurement transducer blocks (continued) Index and name Description List of values Gas standard volume total and in- 1053 = SCF ventory engineering units 1521 = Nm3 SNS_GSV_TotalUnits 1526 = Sm3 Msg type = ENUM 1531 = NL Data type = Unsigned16 (2)
Page 155: Other Additions For Measurement Transducer Blocks

Transducer blocks and views Table A-6: Gas process variables for measurement transducer blocks (continued) Index and name Description List of values Gas standard volume low flow cut- Must be >= 0.0 SNS_GSV_FlowCutoff Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W OOS Available in Release 4.0…
Page 156: Calibration Transducer Blocks

Transducer blocks and views Table A-7: Other additions for measurement transducer blocks (continued) Index and name Description List of values Indicates whether flow is moving in Value part of DS-66 the forward or reverse direction 0 = Forward or Zero Flow SNS_ActualFlowDirection 1 = Reverse Flow Msg type = VAR…
Page 157: Mode_Blk

Transducer blocks and views View Index Name MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — — BLOCK_ALM — — — — TRANSDUCER_DIRECTORY — — — — TRANSDUCER_TYPE TRANSDUCER_TYPE_VER XD_ERROR — — COLLECTION_DIRECTORY — — — — MASS_FLOW_GAIN — —…
Page 158: Standard Fieldbus Parameters For Calibration Transducer Blocks

Transducer blocks and views View Index Name T_DENSITY_FQ_COEFF1 — — — T_DENSITY_FQ_COEFF2 — — — TEMP_LOW_CAL — — — TEMP_HIGH_CAL — — — TEMP_VALUE — — — TEMP_OFFSET — — — TEMP_SLOPE — — — PRESSURE_COMP — — PRESSURE_UNITS — —…
Page 159
Transducer blocks and views Index and name Description List of values The revision level of the static data associ- — ated with the function block. Incremented ST_REV with each write of static store. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = Read only Available in Release 1.0…
Page 160
Transducer blocks and views Index and name Description List of values Occurs when a static parameter is changed — while a block mode is not in out of service UPDATE_EVT (OOS) mode, or when the mode changes from OOS mode and one or more static pa- rameters changed while the block was OOS.
Page 161: Calibration Transducer Blocks

Transducer blocks and views Index and name Description List of values Used for all config, H/W, connection failure 0 = No Error of system problems in the block. 18 = Calibration Error XD_ERROR 19 = Configuration Error Msg type = VAR 20 = Electronics Failure Data type = Unsigned8 (1) 21 = Sensor Failure…
Page 162
Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values Standard deviation of auto zero — ZERO_STD_DEV Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 1.0 Present flow signal offset at zero —…
Page 163
Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values Perform fourth point calibration 0 = None 1 = Start Cal D4_DENSITY_CAL Msg type = METHOD Data type = Unsigned16 (2) Store = — Access = R/W (OOS) Available in Release 1.0 Density calibration constant 1…
Page 164
Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values Density 1 (g/cc) — Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 1.0 Density 2 (g/cc) —…
Page 165
Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values T-Series: Flow FQ Coefficient (FFQ) — T_FLOW_FQ_COEFF Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 1.0 T-Series: Density TG Coefficient —…
Page 166: Pressure Compensation For Calibration Transducer Blocks

Transducer blocks and views Table A-8: Calibration transducer blocks (continued) Index and name Description List of values Temperature value for tempera- — ture calibrations (in degC) TEMP_VALUE Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 1.0 Temperature calibration offset —…
Page 167
Transducer blocks and views Table A-9: Pressure compensation for calibration transducer blocks (continued) Index and name Description List of values Pressure unit 1148 = inH2O (68°F) 1724 = InH2O@60°F PRESSURE_UNITS Msg type = ENUM 1156 = inHg (0°C) Data type = Unsigned16 (2) 1154 = ftH2O (68°F) Store = Static 1151 = mmH2O (68°F)
Page 168: Temperature Compensation For Calibration Transducer Blocks

Transducer blocks and views A.3.5 Temperature compensation for calibration transducer blocks Table A-10: Temperature compensation for calibration transducer blocks Index and name Description List of values Enable/Disable temperature com- 0 = disabled pensation 1 = enabled SNS_ PuckEnableExtTemp Msg type = METHOD Data type = Unsigned16 (2) Store = Static Access = R/W (OOS)
Page 169: Diagnostics Transducer Blocks

Transducer blocks and views Table A-11: Other additions for calibration transducer blocks (continued) Index and name Description List of values Pressure input type 1 = Digital Comm 2 = Fixed PRESSURE_INPUT_TYPE Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 9.0…
Page 170
Transducer blocks and views View Index Name SLUG_LOW_LIMIT — — — — — SLUG_HIGH_LIMIT — — — — — ALARM1_STATUS — — — — ALARM2_STATUS — — — — ALARM3_STATUS — — — — ALARM4_STATUS — — — — FAULT_LIMIT —…
Page 171
Transducer blocks and views View Index Name MFP_TYPE — — — — — MFP_TV_INST — — — — — MFP_TV_INST — — — — — MFP_TV_STD_DEV — — — — — MFP_TV_MAX — — — — — MFP_TV_MIN — — —…
Page 172
Transducer blocks and views View Index Name FRF_StiffnessRpo_ — — — — — stddev FRF_Damping_stddev — — — — — FRF_MassLpo_stddev — — — — — FRF_MassRpo_stddev — — — — — FRF_StiffnessLpo_air — — — — — FRF_StiffnessRpo_air — —…
Page 173
Transducer blocks and views View Index Name FRF_MV_Elapse_Time — — — — — FRF_MV_Time_Left — — — — — FRF_ToneLevel — — — — — FRF_ToneRampTime — — — — — FRF_BlCoeff — — — — — FRF_DriveTarget — — —…
Page 174: Standard Fieldbus Parameters For Diagnostic Transducer Blocks

Transducer blocks and views A.4.2 Standard fieldbus parameters for diagnostic transducer blocks Index and name Description List of values The beginning of the transducer block. — BLOCK_STRUCTURE Msg type = VAR Data type = DS_64 (5) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 The revision level of the static data associ- —…
Page 175
Transducer blocks and views Index and name Description List of values The actual, target, permitted, and normal See section 2.6 of FF-891 modes of the block. MODE_BLK Msg type = REC Data type = DS-69 (4) Store = Mixed Access = RW (OOS) or RW (Auto) Available in Release 1.0 The error status associated with the hard- See section 4.8 of FF-903…
Page 176: Slug Flow Setup For Diagnostic Transducer Blocks

Transducer blocks and views Index and name Description List of values Identifies the version of the transducer — block. Format is XXYY where XX is the ma- TRANSDUCER_ jor spec revision and YY is the manufacturer TYPE_VER revision. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = RW (OOS)
Page 177: Alarm Status For Diagnostic Transducer Blocks

Transducer blocks and views Table A-12: Slug flow setup for diagnostic transducer blocks (continued) Index and name Description List of values High density limit in g/cc — SLUG_HIGH_LIMIT Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W in any mode Available in Release 1.0 A.4.4…
Page 178
Transducer blocks and views Table A-13: Alarm status for diagnostic transducer blocks (continued) Index and name Description List of values Status Word 2 0x0001 = Line RTD Over 0x0002 = Meter RTD Over ALARM2_STATUS Msg type = ENUM 0x0004 = CP Exception Data type = BIT STRING (2) 0x0008 = API: Temp OOL Store = Dynamic/20…
Page 179
Transducer blocks and views Table A-13: Alarm status for diagnostic transducer blocks (continued) Index and name Description List of values Status Word 4 0x0001 = Cal Fail: Low 0x0002 = Cal Fail: High ALARM4_STATUS Msg type = ENUM 0x0004 = Cal Fail: Noisy Data type = BIT STRING (2) 0x0008 = Auto Zero IP Store = Dynamic/20…
Page 180
Transducer blocks and views Table A-13: Alarm status for diagnostic transducer blocks (continued) Index and name Description List of values Alarm index 0 = No Alarm 1 = A001 — (E)EPROM Error (CP) ALARM_INDEX Msg type = ENUM 2 = A002 — RAM Error (CP) Data type = Unsigned16 (2) 3 = A003 — Sensor Failure Store = Static…
Page 181
Transducer blocks and views Table A-13: Alarm status for diagnostic transducer blocks (continued) Index and name Description List of values Failed 35 = A035 — Meter Verification Aborted 36 = A036 — Viscosity Out of Lim- 37 = A037 — Sensor Check Failed 38 = A038 — Time Period Out of Range 42 = A102 — Drive Overrange/Par-…
Page 182: Device Diagnostics From Diagnostics Transducer Block

Transducer blocks and views A.4.5 Device diagnostics from diagnostics transducer block Table A-14: Device diagnostics from diagnostics transducer block List of Index and name Description values Drive gain — DRIVE_GAIN Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 1.0 Raw tube period…
Page 183
Transducer blocks and views Table A-14: Device diagnostics from diagnostics transducer block (continued) List of Index and name Description values Maximum electronics temperature — ELECT_TEMP_ Msg type = VAR Data type = FLOAT (4) Store = Dynamic/20 Access = Read only Available in Release 2.0 Minimum electronics temperature —…
Page 184: Meter Fingerprinting For Diagnostic Transducer Blocks

Transducer blocks and views Table A-14: Device diagnostics from diagnostics transducer block (continued) List of Index and name Description values Meter RTD resistance in ohms — RTD_RESISTANCE_ Msg type = VAR METER Data type = FLOAT (4) Store = Dynamic/20 Access = Read only Available in Release 3.0 Number of core processor power cycles…
Page 185
Transducer blocks and views Table A-15: Meter fingerprinting for diagnostic transducer blocks (continued) Index and name Description List of values Meter fingerprint in SI (0) or English 0x0000 = SI (1) units 0x0001 = English MFP_UNITS Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W in any mode…
Page 186: Other Additions For Diagnostics Transducer Blocks

Transducer blocks and views Table A-15: Meter fingerprinting for diagnostic transducer blocks (continued) Index and name Description List of values Transmitter variable, maximum — (since last statistics reset) MFP_TV_MAX Msg type = VAR Data type = FLOAT (4) Store = Dynamic Access = Read only Available in Release 3.0 Transmitter variable, minimum…
Page 187
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values Actual target amplitude (mV/Hz) — (pre 700 2.1, actual & override) SNS_TargetAmplitude Msg type = VAR Data type = FLOAT (4) Store = Dynamic Access = Read only Available in Release 4.0…
Page 188
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values Start/Stop meter verification — (ap- 0= Disabled plicable only if meter verification is 1 = Fixed output mode FRF_EnableFCFValidation enabled) 2 = Factory air verification 3 = Factory water verification Msg type = METHOD…
Page 189
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The reason the meter verification 0 = No error routine aborted 1 = Manual abort FRF_AbortCode 2 = Watchdog timeout Msg type = ENUM 3 = Frequency drift Data type = Unsigned16 (2)
Page 190
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The current RPO stiffness calcula- — ted as a mean FRF_StiffnessRpo_mean Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 4.0…
Page 191
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The current damping calculated as — a standard deviation FRF_Damping_stddev Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 4.0 The current LPO mass calculated as…
Page 192
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The LPO mass calculated as a mean — during Factory Cal of Air FRF_MassLpo_air Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 4.0…
Page 193
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values The RPO mass calculated as a mean — during Factory Cal of Water FRF_MassRpo_water Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 4.0…
Page 194
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values FCF Datalog Item 2: Status; Abort Bit 7 = FCF pass/fail states are compressed to fit into 3 Bits 6-4 = state FRF_MV_Status bits Bits 3-0 = abort code…
Page 195
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #100 Temperature — FRF_Temp Msg type = VAR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 6.0 #101 Density…
Page 196
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #106 FCF timers: time until first run in — hours (applicable only if meter veri- FRF_MV_FirstRun_Time fication feature is enabled) Msg type = VAR Data type = FLOAT (4) Store = Static…
Page 197
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #111 BL coefficient (applicable only if — meter verification feature is ena- FRF_BlCoeff bled) Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 7.0…
Page 198
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #116 Maximum sensor current (applica- — ble only if meter verification feature FRF_Max_Current_mA is enabled) Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 7.0…
Page 199
Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #121 Temperature unit 1000 = K 1001 = Deg C DIAG_TEMPERATURE_ Msg type = ENUM 1002 = Deg F UNITS Data type = Unsigned16 (2) 1003 = Deg R Store = Static…
Page 200: Device Information Transducer Blocks

Transducer blocks and views Table A-16: Other additions for diagnostics transducer blocks (continued) Index and name Description List of values #126 Indexed by R2984 — DIAG_FRF_RPO_METER_ Msg type = VAR FACTOR Data type = FLOAT (4) Store = Static Access = Read only Available in Release 8.0 #127 Indexed by R2984…
Page 201
Transducer blocks and views View Index Name STRATEGY — — — ALERT_KEY — — — MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — — BLOCK_ALM — — — — TRANSDUCER_DIRECTORY — — — — TRANSDUCER_TYPE TRANSDUCER_TYPE_VER XD_ERROR — —…
Page 202: Standard Fieldbus Parameters For Device Information Transducer Blocks

Transducer blocks and views A.5.2 Standard fieldbus parameters for device information transducer blocks Index and name Description List of values The beginning of the transducer block. — BLOCK_STRUCTURE Msg type = VAR Data type = DS_64 (5) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 The revision level of the static data associ-…
Page 203
Transducer blocks and views Index and name Description List of values The actual, target, permitted, and normal See section 2.6 of FF-891 modes of the block. MODE_BLK Msg type = REC Data type = DS-69 (4) Store = Mixed Access = RW (OOS) or RW (Auto) Available in Release 1.0 The error status associated with the hard- See section 4.8 of FF-903…
Page 204: Transmitter Data For Device Information Transducer Blocks

Transducer blocks and views Index and name Description List of values Identifies the version of the transducer — block. Format is XXYY where XX is the ma- TRANSDUCER_ jor spec revision and YY is the manufacturer TYPE_VER revision. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = RW (OOS)
Page 205: Sensor Data For Device Information Transducer Blocks

Transducer blocks and views Table A-17: Transmitter data for device information transducer blocks (continued) Index and name Description List of values Model 700 transmitter software re- — vision 700_SW_REV Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = Read only Available in Release 1.0 Model 2700 transmitter software…
Page 206
Transducer blocks and views Table A-18: Sensor data for device information transducer blocks (continued) Index and name Description List of values Sensor type (i.e. F200, CMF025) — SENSOR_TYPE Msg type = STR Data type = VISIBLE STRING (16) Store = Static Access = Read only Available in Release 1.0 Sensor type code…
Page 207
Transducer blocks and views Table A-18: Sensor data for device information transducer blocks (continued) Index and name Description List of values Flange type 0 = ANSI 150 [CP, ECP, FDM, FVM] SENSOR_END Msg type = ENUM 1 = ANSI 300 Data type = Unsigned16 (2) 2 = ANSI 600 Store = Static…
Page 208
Transducer blocks and views Table A-18: Sensor data for device information transducer blocks (continued) Index and name Description List of values Device type for the attached core 40 = 700 [CP] processor 50 = 800 [ECP] SNS_PuckDeviceTypeCode 61 = Density Msg type = ENUM Data type = Unsigned16 (2) Store = Static…
Page 209: Local Display Transducer Blocks

Transducer blocks and views Local display transducer blocks A.6.1 View list for local display transducer block The following table lists the parameters contained in the transducer block for local display parameters. Four views are defined for the local display transducer block. The table also shows the applicable views for each parameter, and the size of the parameter in that view, in bytes.
Page 210: Standard Fieldbus Parameters For Local Display Transducer Blocks

Transducer blocks and views View Index Name LDO_VAR_3_CODE — — — LDO_VAR_4_CODE — — — LDO_VAR_5_CODE — — — LDO_VAR_6_CODE — — — LDO_VAR_7_CODE — — — LDO_VAR_8_CODE — — — LDO_VAR_9_CODE — — — LDO_VAR_10_CODE — — — LDO_VAR_11_CODE —…
Page 211
Transducer blocks and views Index and name Description List of values The revision level of the static data associ- — ated with the function block. Incremented ST_REV with each write of static store. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = Read only Available in Release 1.0…
Page 212
Transducer blocks and views Index and name Description List of values Occurs when a static parameter is changed — while a block mode is not in out of service UPDATE_EVT (OOS) mode, or when the mode changes from OOS mode and one or more static pa- rameters changed while the block was OOS.
Page 213: Local Display Transducer Blocks

Transducer blocks and views Index and name Description List of values Used for all config, H/W, connection failure 0 = No Error of system problems in the block. 18 = Calibration Error XD_ERROR 19 = Configuration Error Msg type = VAR 20 = Electronics Failure Data type = Unsigned8 (1) 21 = Sensor Failure…
Page 214
Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values Enable/Disable LDO offline menu fea- 0 = Disable ture 1 = Enable EN_LDO_OFFLINE_MENU Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W in any mode Available in Release 1.0…
Page 215
Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values Display the language selection 0 = English 1 = German UI_Language Msg type = ENUM 2 = French Data type = Unsigned16 (2) 3 = Reserved Store = Static 4 = Spanish…
Page 216
Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values #25 LDO_VAR_1_CODE Displays the variable associated with 0 = Mass Flow Rate [700, 800] #26 LDO_VAR_2_CODE the code on the LDO 1 = Temperature #27 LDO_VAR_3_CODE 2 = Mass Total [700, 800] Msg type = ENUM…
Page 217
Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values 63 = Gas Std Vol Total [700, 800] 64 = Gat Std Vol Inventory [700, 800] 69 = Live Zero [700, 800] 159 = User Defined Equation [CDM, FDM, FVM] 161 = Tube-Case Temperature…
Page 218: Petroleum Measurement Transducer Blocks

Transducer blocks and views Table A-19: Local display transducer blocks (continued) Index and name Description List of values Enable/Disable display status LED 0 = Disable blinking 1 = Enable UI_EnableStatusLedBlinking Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W in any mode Available in Release 4.0 Enable/Disable display alarm screen…
Page 219
Transducer blocks and views View Index Name BLOCK_STRUCTURE — — — — ST_REV TAG_DESC — — — — STRATEGY — — — ALERT_KEY — — — MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — — BLOCK_ALM — — —…
Page 220: Standard Fieldbus Parameters For Petroleum Measurement Transducer Blocks

Transducer blocks and views A.7.2 Standard fieldbus parameters for petroleum measurement transducer blocks Index and name Description List of values The beginning of the transducer block. — BLOCK_STRUCTURE Msg type = VAR Data type = DS_64 (5) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 The revision level of the static data associ-…
Page 221
Transducer blocks and views Index and name Description List of values The actual, target, permitted, and normal See section 2.6 of FF-891 modes of the block. MODE_BLK Msg type = REC Data type = DS-69 (4) Store = Mixed Access = RW (OOS) or RW (Auto) Available in Release 1.0 The error status associated with the hard- See section 4.8 of FF-903…
Page 222: Process Variables For Petroleum Measurement Transducer Blocks

Transducer blocks and views Index and name Description List of values Identifies the version of the transducer — block. Format is XXYY where XX is the ma- TRANSDUCER_ jor spec revision and YY is the manufacturer TYPE_VER revision. Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = RW (OOS)
Page 223
Transducer blocks and views Table A-20: Process variables for petroleum measurement transducer blocks (continued) Index and name Description List of values Batch weighted average density — API_Ave_Corr_Density Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 3.0 Batch weighted average tempera- —…
Page 224: Setup Data For Petroleum Measurement Transducer Blocks

Transducer blocks and views A.7.4 Setup data for petroleum measurement transducer blocks Table A-21: Setup data for petroleum measurement transducer blocks Index and name Description List of values Enable/Disable petroleum measure- 0 = disabled ment 1 = enabled EN_API Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = Read only…
Page 225
Transducer blocks and views Table A-21: Setup data for petroleum measurement transducer blocks (continued) Index and name Description List of values Reset PM/GSV inventory 0 = No effect 1 = Reset SNS_ResetAPIGSVInv Msg type = METHOD Data type = Unsigned16 (2) Store = Static Access = R/W in any mode Available in Release 4.0…
Page 226
Transducer blocks and views Table A-21: Setup data for petroleum measurement transducer blocks (continued) Index and name Description List of values Standard or special volume flow rate 1347 = m3/s unit 1348 = m 3/min API_VOL_FLOW_UNITS 1349 = m3/h Msg type = ENUM 1350 = m3/d Data type = Unsigned16 (2) 1351 = L/s…
Page 227: Concentration Measurement Transducer Blocks

Transducer blocks and views Table A-21: Setup data for petroleum measurement transducer blocks (continued) Index and name Description List of values Pressure units 1148 = inH2O (68°F) 1724 = InH2O@60°F API_PressureUnit Msg type = ENUM 1156 = inHg (0°C) Data type = Unsigned16 (2) 1154 = ftH2O (68°F) Store = Static 1151 = mmH2O (68°F)
Page 228
Transducer blocks and views View Index Name BLOCK_STRUCTURE — — — — ST_REV TAG_DESC — — — — STRATEGY — — — ALERT_KEY — — — MODE_BLK — — BLOCK_ERR — — UPDATE_EVT — — — — BLOCK_ALM — — —…
Page 229
Transducer blocks and views View Index Name ED_Temp_Index — — — ED_Conc_Index — — — ED_Temp_ISO — — — ED_Dens_At_Temp_ISO — — — ED_Dens_At_Temp_Coeff — — — ED_Conc_Label_55 — — — ED_Dens_At_Conc — — — ED_Dens_At_Conc_Coeff — — — ED_Conc_Label_51 —…
Page 230: Standard Fieldbus Parameters For Concentration Measurement Transducer Blocks

Transducer blocks and views View Index Name ED_SYS_AttachedCoreType — — — SNS_ED_ConcUnits_SpecialUnit — — — ED_MASSFLOW_UNITS — — — ED_VOL_TOT_UNITS — — — ED_MASS_TOT_UNITS — — — A.8.2 Standard fieldbus parameters for concentration measurement transducer blocks Index and name Description List of values The beginning of the transducer block.
Page 231
Transducer blocks and views Index and name Description List of values The identification number of the plant unit. 1 to 255 This information may be used in the host ALERT_KEY for sorting alarms, etc. Msg type = VAR Data type = Unsigned8 (1) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0…
Page 232
Transducer blocks and views Index and name Description List of values A directory that specifies the number and — starting indices of the data collections in TRANSDUCER_ the transducer block. DIRECTORY Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = RW (OOS) Available in Release 9.0…
Page 233: Process Variables For Concentration Measurement Transducer Blocks

Transducer blocks and views A.8.3 Process variables for concentration measurement transducer blocks Table A-22: Process variables for concentration measurement transducer blocks Index and name Description List of values Density at reference — ED_Ref_Dens Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 3.0…
Page 234: Totals For Concentration Measurement Transducer Blocks

Transducer blocks and views Table A-22: Process variables for concentration measurement transducer blocks (continued) Index and name Description List of values Density (fixed baume units) — ED_Baume Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 3.0 A.8.4 Totals for concentration measurement transducer…
Page 235: Setup Data For Concentration Measurement Transducer Blocks

Transducer blocks and views Table A-23: Totals for concentration measurement transducer blocks (continued) Index and name Description List of values Net volume inventory — ED_Net_Vol_Inv Msg type = VAR Data type = DS-65 (5) Store = Dynamic/20 Access = Read only Available in Release 3.0 Reset concentration measurement Value part of DS-66…
Page 236
Transducer blocks and views Table A-24: Setup data for concentration measurement transducer blocks (continued) Index and name Description List of values Lock enhanced density tables 0 = not locked 1 = locked ED_Curve_Lock Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 3.0…
Page 237
Transducer blocks and views Table A-24: Setup data for concentration measurement transducer blocks (continued) Index and name Description List of values Curve (6×5) temperature iso- — therm value (x-axis) ED_Temp_ISO Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 3.0 Curve…
Page 238
Transducer blocks and views Table A-24: Setup data for concentration measurement transducer blocks (continued) Index and name Description List of values Curve (5×1) concentration value — (y-axis) ED_Conc_Label_51 Msg type = VAR Data type = FLOAT (4) Store = Static Access = R/W (OOS) Available in Release 3.0 Curve…
Page 239
Transducer blocks and views Table A-24: Setup data for concentration measurement transducer blocks (continued) Index and name Description List of values Curve ASCII string – name of curve — – 12 characters supported ED_Curve_Name Msg type = VAR Data type = VISIBLE STRING (12) Store = Static Access = R/W in any mode Available in Release 3.0…
Page 240: Other Additions For Concentration Measurement Transducer Blocks

Transducer blocks and views A.8.6 Other additions for concentration measurement transducer blocks Table A-25: Other additions for concentration measurement transducer blocks Index and name Description List of values Reset concentration measurement 0 = No effect volume inventory 1 = Reset SNS_ResetEDVolInv Msg type = METHOD Data type = Unsigned16 (2)
Page 241
Transducer blocks and views Table A-25: Other additions for concentration measurement transducer blocks (continued) Index and name Description List of values Enable high density extrapolation 1 = Enable alarm SNS_ED_EnableDensHighEx- trap Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W in any mode Available in Release 4.0…
Page 242
Transducer blocks and views Table A-25: Other additions for concentration measurement transducer blocks (continued) Index and name Description List of values Standard or special volume flow rate 1347 = m3/s unit 1348 = m 3/min ED_VOL_FLOW_UNITS 1349 = m3/hr Msg type = ENUM 1350 = m3/day Data type = Unsigned16 (2) 1351 = L/s…
Page 243
Transducer blocks and views Table A-25: Other additions for concentration measurement transducer blocks (continued) Index and name Description List of values Enable concentration measurement 0 = disabled curve auto-switching 1 = enabled DEN_Enable_CMAutoswitch Msg type = VAR Data type = Unsigned16 (2) Store = —…
Page 244: Density Viscosity Meter Transducer Blocks

Transducer blocks and views Table A-25: Other additions for concentration measurement transducer blocks (continued) Index and name Description List of values Volume flow total unit 1034 = m3 1036 = cm3 ED_VOL_TOT_UNITS Msg type = ENUM 1038 = L Data type = Unsigned16 (2) 1043 = ft3 Store = Dynamic 1048 = gallon…
Page 245
Transducer blocks and views View Index Name TRANSDUCER_ — — — — — — — — DIRECTORY TRANSDUCER_TYPE — — — — TRANSDUCER_TYPE_ — — — — XD_ERROR — — — — — — COLLECTION_ — — — — — —…
Page 246
Transducer blocks and views View Index Name DEN_KV5 — — — — — — — DEN_KV6 — — — — — — — DEN_CalibrationStatus — — — — — — — DEN_KV_Index — — — — — — — DEN_KV_Crossover —…
Page 247
Transducer blocks and views View Index Name DEN_Programmable- — — — — — — — ConstF DEN_Programmable- — — — — — — — ValA DEN_Programmable- — — — — — — — ValB DEN_Programmable- — — — — — —…
Page 248
Transducer blocks and views View Index Name DEN_KinematicViscosi- — — — — — — — tyUnits VISC_RANGE_SEL_IN- — — — — — — — DEN_V0 — — — — — — — DEN_V1 — — — — — — — DEN_V2 —…
Page 249
Transducer blocks and views View Index Name MBUS_Visc_CurveIn- — — — — — — — MBUS_Visc_TempIn- — — — — — — — DEN_RefVisc_Mat_ — — — — — — — MaxFitOrder EN_RefVisc_Mat_Tem- — — — — — — — pISO DEN_RefVisc_Mat_Vis- —…
Page 250
Transducer blocks and views View Index Name DEN_CaseTemperatur- — — — — — — — eStability DEN_SpecialEquation- — — — — — — — Type DEN_Legacy_K0 — — — — — — — DEN_Legacy_K1 — — — — — — —…
Page 251: Standard Fieldbus Parameters For Density Viscosity Meter Transducer Blocks

Transducer blocks and views View Index Name PRESSURE_UNITS — — — — — — — DEN_ProductCode — — — — — — — — Velocity_Switch_Sta- — — — — — — — DEN_RefWaterDensity — — — — — — — DEN_RefTemperature —…
Page 252
Transducer blocks and views Index and name Description List of values The user description of the intended block Any 32 characters application. TAG_DESC Msg type = STR Data type = OCTET STRING (32) Store = Static Access = RW (OOS) or RW (Auto) Available in Release 1.0 Used to identify grouping of blocks.
Page 253
Transducer blocks and views Index and name Description List of values Occurs when a static parameter is changed — while a block mode is not in out of service UPDATE_EVT (OOS) mode, or when the mode changes from OOS mode and one or more static pa- rameters changed while the block was OOS.
Page 254: Process Variables For Density Viscosity Transducer Blocks

Transducer blocks and views Index and name Description List of values Used for all config, H/W, connection failure 0 = No Error of system problems in the block. 18 = Calibration Error XD_ERROR 19 = Configuration Error Msg type = VAR 20 = Electronics Failure Data type = Unsigned8 (1) 21 = Sensor Failure…
Page 255
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Curve configuration index (n) 1 = Use user sensor check value DEN_UseUserSensorCheck Msg type = VAR 0 = Use factory sensor Value Data type = Unsigned16 (2) check value…
Page 256
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Densisty scale factor — DensityScaleFactor Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 8.0 Temperature scale factor —…
Page 257
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values K2, instrument calibration factor — DEN_K2 Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0 K18, instrument calibration factor —…
Page 258
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values KV calibration factor index (0-1) 0: Medium 1: High DEN_KV_Index Msg type = ENUM (1) Data type = Unsigned8 (1) Store = Static Access = R/W in any mode Available in Release 8.0…
Page 259
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values A6, density calibration constant — DEN_A6 Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0 A7, density calibration constant —…
Page 260
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Fixed flow velocity value (m/sec) — DEN_FixedVelocity Msg type = VAR Data type = DS65 Store = Dynamic/20 Access = Read only Available in Release 8.0 Flow velocity units 1061 = Meters/Sec-…
Page 261
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Time period (u/sec) (upper 3dB point) — DEN_TimePeriodB Msg type = VAR Data type = Float (4) Store = Dynamic/20 Access = Read only Available in Release 8.0 Time period (u/sec) (lower 3dB point)
Page 262: Den_Programmable

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Programmable constant E for special — equation (Y for special equation type I) DEN_ProgrammableConstE Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 263: Den_Programmable

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Programmable constant D for special — equation — constants available for access DEN_ProgrammableValD using pointers for special equations (reg- isters 4114-4119) Msg type = VAR Data type = Float (4)
Page 264: Den_Specialeqnslota

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Pointer A for special equation 1 = Temperature 3 = Density DEN_SpecialEqnSlotA Msg type = ENUM 5 = Volume Flow Rate Data type = Unsigned16 (2) [CDM] Store = Static…
Page 265: Den_Specialeqnslotb

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Pointer B for special equation See #74 DEN_Special- EqnSlotA DEN_SpecialEqnSlotB Msg type = ENUM Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 266: Den_Qualityfactor

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Special equation unit string — DEN_SpecialEqnLabel Msg type = STR Data type = VISIBLE STRING Store = Static Access = R/W (OOS) Available in Release 8.0 Special density unit string —…
Page 267: Den_Dynamicviscosity

Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values Dynamic viscosity — DEN_DynamicViscosity Msg type = VAR Data type = DS65 Store = Dynamic Access = Read only Available in Release 8.0 Kinematic viscosity —…
Page 268
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values V2 at the selected range — Array of 4 — DEN_V2 Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 269
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #102 Special kinematic viscosity unit string Visible string DEN_KinViscSpecialUnitLabel Msg type = STR Data type = VISIBLE STRING Store = Static Access = R/W (OOS) Available in Release 8.0 #103…
Page 270
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #109 Average time period on air/vacuum (in- — dexed by DEN_KDV_CalIndex) DEN_AverageTimePeriod Msg type = VAR Data type = Float (4) Store = Static Access = Read only Available in Release 8.0…
Page 271
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #114 Referred viscosity calculation method 0 = referral matrix 1 = ASTM D341 single DEN_ReferredViscMethod Msg type = ENUM curve Data type = Unsigned16 (2) 2 = ASTM D341 multi-…
Page 272
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #119 Referred viscosity (6×6) @ temperature — isothermX, curve (indexed by MBUS_ DEN_RefVisc_Mat_ Visc_CurveIndex and MBUS_Visc_Tem- ViscAtTempISO pIndex) Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS)
Page 273
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #125 Number of ASTM reference curves (n = — 2-8) DEN_RefVisc_ASTM_NumCurves Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 274
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #130 Lab viscosity for viscosity scaling factor — calibration DEN_LabViscosity Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 275
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #137 Case temperature stability (sensor check) — DEN_CaseTemperatureStability Msg type = VAR Data type = Float (4) Store = Static Access = Read only Available in Release 8.0 #138…
Page 276
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #144 K20A constant used to compute K20 (in- — dexed by DEN_Legacy_K20_K21_Index) DEN_Legacy_K20A Msg type = VAR Data type = Float (4) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 277
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #150 Time period A (in microseconds) — DEN_TPA_Microsec Msg type = VAR Data type = DS65 Store = Dynamic Access = Read only Available in Release 8.0 #151…
Page 278
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #157 Index for KDV results 0 = Factory 1 = User DEN_KDV_CalIndex Msg type = VAR Data type = Unsigned16 (2) Store = Static Access = R/W (OOS) Available in Release 8.0…
Page 279
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #163 Secondary referred viscosity — DEN_SecBaseViscosity Msg type = VAR Data type = DS65 Store = Dynamic Access = Read only Available in Release 8.0 #164 Unit for reference and secondary refer-…
Page 280
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #167 Pressure unit 1148 = inch water @ 68F / inch water@60F PRESSURE_UNITS Msg type = ENUM 1156 = inch HG @ 0C Data type = Unsigned16 (2) 1154 = ft water @ 68F Store = Dynamic…
Page 281
Transducer blocks and views Table A-26: Process variables for density viscosity transducer blocks (continued) Index and name Description List of values #171 Reference temperature for inline calibra- — tion DEN_RefTemperature Msg type = VAR Data type = Float (4) Store = Static Access = R/W in any mode Available in Release 9.0 #172…
Page 282
Transducer blocks and views (1) The list within the square bracket contains cores that support this value. Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 283: Appendix B Fieldbus Channel References

Fieldbus channel references Appendix B Fieldbus channel references Table B-1: Analog input function blocks Channel number Channel description Valid unit code Core applicability Mass Flow Measurement TB > Mass Flow Units Temperature Measurement TB > Temperature Units Density Measurement TB > Density Units Volume Flow Measurement TB >…
Page 284
Fieldbus channel references Table B-1: Analog input function blocks (continued) Channel number Channel description Valid unit code Core applicability ED Specific Gravity Measurement TB > Density Units ED Std Vol Flow Measurement TB > Volume Flow Units ED Net Mass Flow Measurement TB >…
Page 285
Fieldbus channel references Table B-3: Discrete input function blocks (continued) Channel number Channel description Core applicability SNS ZeroInProgress SYS AnalogOutputFault SNS MVFailed Table B-4: Discrete output function blocks Channel number Channel description Core applicability Start Sensor Zero Reset Mass Total Reset Volume Total Reset API Reference (Standard) Volume Total Reset All Process Totals (not Inv)
Page 286
Fieldbus channel references Table B-5: AI function blocks Channel number Channel description Valid unit code Core applicability Special Equation Output 1588 = No Units Time Period A 1057 — Micro Second Time Period B 1057 — Micro Second Tube-case temperature differential Measurement TB >…
Page 287: Foundation

™ FOUNDATION fieldbus function blocks Appendix C ™ FOUNDATION fieldbus function blocks Topics covered in this appendix: • Analog Input (AI) function block • Analog Output (AO) function block • Integrator (INT) Function Block • Discrete Input (DI) function block •…
Page 288: Ai Block Modes

™ FOUNDATION fieldbus function blocks • OUT_SCALE: The high and low scale values, engineering units code, and number of digits to the right of the decimal point associated with OUT when L_TYPE is not direct. • SIMULATE: A group of data that contains the current transducer value and status, the simulated transducer value and status, and the enable/disable bit.
Page 289
™ FOUNDATION fieldbus function blocks CHANNEL Select the channel that corresponds to the desired sensor measurement. The following table provides a list of AI Function block channel numbers and channel applicability depending upon attached core type to transmitter. If a channel is not supported for the given core type, the channel value will not work for the transmitter.
Page 290
™ FOUNDATION fieldbus function blocks Table C-1: AI block channel definitions (continued) Channel Description Flow velocity (1) This channel assignment is supported only by CDM software revision 2.0 and above. L_TYPE The L_TYPE parameter defines the relationship of the sensor measurement to the desired output of the AI block.
Page 291: Ai Block Filtering

™ FOUNDATION fieldbus function blocks C.1.5 AI block filtering The filtering feature changes the response time of the device to smooth variations in output readings caused by rapid changes in input. Adjust the filter time constant (in seconds) using the PV_FTIME parameter. Set the filter time constant to zero to disable the filter feature.
Page 292: Ai Block Status Handling

™ FOUNDATION fieldbus function blocks Number Description The priority of an alarm condition changes to 0 after the condition that caused the alarm is corrected. An alarm condition with a priority of 1 is recognized by the system, but is not reported to the operator.
Page 293: Analog Output (Ao) Function Block

™ FOUNDATION fieldbus function blocks AI1 (AI_2600_ AI2 (AI_2800_ AI3 (AI3000_ AI4 (AI_3200_ xxxx) xxxx) xxxx) xxxx Channel Mass flow (1) Temperature (2) Density (3) Volume flow (4) OUT_SCALE EU_100 EU_0 Unit_Index Decimal L_TYPE Direct Direct Direct Direct Analog Output (AO) function block The AO block converts the FF value to a channel value by using two sets of scaling values.
Page 294: Ao Block Modes

™ FOUNDATION fieldbus function blocks • PV_SCALE: PV_SCALE is used to convert the FF value in SP to percent. The units are usually percent. • XD_SCALE: XD_SCALE is used to convert the percent FF value to the value for the channel, which should be given in the device manual.
Page 295: Ao Block Simulation

™ FOUNDATION fieldbus function blocks C.2.4 AO block simulation When simulation is enabled, the last value of OUT is maintained and reflected in the field value of the SIMULATE attribute. In this case, the PV and READBACK values and statuses are based on the SIMULATE value and the status that you enter.
Page 296: Integrator (Int) Function Block

™ FOUNDATION fieldbus function blocks Integrator (INT) Function Block The Integrator (INT) function block integrates one or two variables over time. The block compares the integrated or accumulated value to pre-trip and trip limits and generates discrete output signals when the limits are reached. The INT integrates one process value.
Page 297: Int Block Configuration Parameters

™ FOUNDATION fieldbus function blocks This block is intended to have measurements that come from a process calculation path. It will work with input from a control path. The block output starts a process calculation path. The block is unusual because the status of the output has to be calculated. The output status is not directly related to the status of the inputs.
Page 298: Int Block Other Parameters

If the Confirm reset is set, the block shall not process subsequent re- set at RESET_IN until RESET_CONFIRM discrete input is TRUE. Input 1 pass through This is special option only used for Emerson Integrator block to pass internal totals to Integrator block. •…
Page 299: Int Block Modes

™ FOUNDATION fieldbus function blocks • SRTOTAL: The read-only snapshot of RTOTAL just before a reset. Same units as OUT. • N_RESET: Counts the number of resets. It can not be written or reset. C.3.3 INT block modes The Integrator function block supports the following modes: •…
Page 300: Int Block Special Mode

™ FOUNDATION fieldbus function blocks C.3.6 INT block special mode Enhanced FF host Overview > Totalizer Control > Configure Integrator Block Fieldbus Host Measurement TB > INTEGRATOR_FB_CONFIG (OD Index 50) Along with standard operation of integrating the process value at INn, the Micro Motion Integrator function block has one special mode of operation: Input 1 pass through.
Page 301: Int Block Default Configuration

™ FOUNDATION fieldbus function blocks Fieldbus code Label Description Internal ED: Net Block outputs internal ED: net mass total value and RESET_IN re- Mass Total sets internal ED: net mass total Internal ED: Net Block outputs internal ED: net mass inventory value and RESET_IN Mass Inventory resets internal ED: net mass inventory Internal ED: Net…
Page 302: Di Block Modes

™ FOUNDATION fieldbus function blocks Channel Description Zero in progress Analog output fault Meter verification failed • IO_OPTS: allows the option to have the value of FIELD_VAL_D be logically inverted before becoming the PV_D, if the “Invert” option is selected. •…
Page 303: Di Block Default Configuration

™ FOUNDATION fieldbus function blocks C.4.6 DI block default configuration DI1 (DI_4400_xxxx) CHANNEL Analog Output Fault (33) IO_OPTS 0x0000 STATUS_OPTS 0x0000 Discrete Output (DO) function block The Discrete Output (DO) function block processes a discrete setpoint and saves it to a specified channel to produce an output signal.
Page 304: Do Block Modes

™ FOUNDATION fieldbus function blocks • IO_OPTS: Options which the user may select to alter input and output block processing. Invert — Causes the SP_D value to be inverted before it becomes the output. May be used for normally open solenoid valves and other inverted actuators. SP-PV Track in Man — The value of SP is set to the value of PV when the target mode is Man.
Page 305: Do Block Errors

™ FOUNDATION fieldbus function blocks C.5.3 DO block errors The following conditions are reported in the BLOCK_ERR attribute: • Simulate Active: SIMULATE_D is enabled; therefore, PV_D is not real. • Input failure/process variable has Bad status: The readback value is bad. •…
Page 306
™ FOUNDATION fieldbus function blocks Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 307: Appendix D Using The Transmitter Display

Using the transmitter display Appendix D Using the transmitter display Using the display D.1.1 Components of the transmitter interface The transmitter interface includes the status LED, the display (LCD panel), and two optical switches. Figure D-1: Transmitter interface Status LED Display (LCD panel) Process variable Scroll optical switch…
Page 308: Use The Optical Switches

Using the transmitter display Note Display refers to the display on the remotely mounted transmitter, not directly mounted to the meter. If there is a display directly on the meter, it can only view process variables, and it cannot be used for any other operation.
Page 309
Using the transmitter display Prerequisites To access the display menu system, operator access to either the Off-Line menu or the Alert menu must be enabled. To access the complete menu system, operator access must be enabled for both the Off-Line menu and the Alert menu. Procedure At the transmitter display, activate theScroll and Select optical switches simultaneously until the display changes.
Page 310
Using the transmitter display • Exit each menu separately, working your way back to the top of the menu system. • Wait until the display times out and returns to displaying process variable data. Enter a floating-point value using the display Certain configuration values (for example, Lower Range Value and Upper Range Value) are entered as floating-point values.
Page 311
Using the transmitter display If the current value is positive and there is a blank space at the left of the value, activate Select until the cursor is flashing under the blank space, then activate Scroll until the minus sign appears. If the current value is positive and there is no blank space at the left of the value, activate Select until the cursor is flashing under the leftmost digit, then activate Scroll until the minus sign appears.
Page 312
Using the transmitter display • S = Sign. A minus sign (−) indicates a negative number. A blank indicates a positive number. • X.XXX = The 4-digit mantissa. • E = The exponent indicator. • YY = The 2-digit exponent. Procedure Switch from decimal notation to exponential notation.
Page 313: Display Codes For Process Variables

Using the transmitter display To save the displayed value to transmitter memory, activate Scroll and Select simultaneously and hold until the display changes. • If the displayed value is the same as the value in transmitter memory, you will be returned to the previous screen.
Page 314: Codes And Abbreviations Used In Display Menus

Using the transmitter display Table D-2: Display codes for process variables (continued) Code Definition Comment or reference STD V Standard volume flow rate Concentration measurement application only STDVI Standard volume inventory Concentration measurement application only TCDENS Temperature-corrected density Petroleum measurement application only TCORI Temperature-corrected inventory Petroleum measurement application only…
Page 315
Using the transmitter display Table D-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference CUSTODY XFER Custody transfer DENS Density D EV Discrete event Events configured using the enhanced event model DGAIN, DRIVE % Drive gain DISBL Disable…
Page 316
Using the transmitter display Table D-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference INTERN Internal Input/output LANG Language LOCK Write-protect LOOP CUR Loop current M_ASC Modbus ASCII M_RTU Modbus RTU MAO1 mA Output 1 (primary mA Output) MAO2…
Page 317
Using the transmitter display Table D-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference WRPRO Write protect PVR applications only XMTR Transmitter Configuration and Use Manual…
Page 318
Using the transmitter display Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 319: Appendix E Using Prolink Iii With The Transmitter

In most ProLink III installations, the manual is installed with the ProLink III program. Additionally, the ProLink III manual is available on the documentation CD or at www.emerson.com. ProLink III features and functions ProLink III offers complete transmitter configuration and operation functions. ProLink III also offers a number of additional features and functions, including: •…
Page 320
Using ProLink III with the transmitter ProLink III messages As you use ProLink III with a Micro Motion transmitter, you will see a number of messages and notes. This manual does not document all of these messages and notes. Important The user is responsible for responding to messages and notes and complying with all safety messages.
Page 321: Appendix F Using A Field Communicator With The Transmitter

If you are unable to perform these tasks, consult the Field Communicator manual before attempting to use the Field Communicator. The Field Communicator manual is available on the documentation CD or at www.emerson.com. Field Communicator menus and messages Many of the menus in this manual start with the On-Line menu. Ensure that you are able to navigate to the On-Line menu.
Page 322: Connect With The Ff Host

Using a Field Communicator with the transmitter Connect with the FF host A connection from the FOUNDATION Fieldbus host to your transmitter allows you to read process data, configure the transmitter, and perform maintenance and troubleshooting tasks. Procedure Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 323: Appendix G Default Values And Ranges

Default values and ranges Appendix G Default values and ranges Default values and ranges The default values and ranges represent the typical factory transmitter configuration. Depending on how the transmitter was ordered, certain values may have been configured at the factory and are not represented in the default values and ranges. Table G-1: Transmitter default values and ranges Type…
Page 324
Default values and ranges Table G-1: Transmitter default values and ranges (continued) Type Parameter Default Range Comments Density units g/cm Density cutoff 0.2 g/cm 0.0 – 0.5 g/cm 0 g/cm 1 g/cm 1000 µsec 1000 – 50,000 µsec 50,000 µsec 1000 –…
Page 325
Default values and ranges Table G-1: Transmitter default values and ranges (continued) Type Parameter Default Range Comments External pressure 0.000 psi Mass flow rate 200.000 g/s Volume flow rate 0.200 L/s Density 10.000 g/cm Temperature 450.000 °C Drive gain 100.000% Gas standard volume flow rate 423.78 SCFM External temperature…
Page 326
Default values and ranges Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 327: Appendix H Transmitter Components And Installation Wiring

Transmitter components and installation wiring Appendix H Transmitter components and installation wiring Topics covered in this appendix: • Installation types • Power supply terminals and ground • Fieldbus wiring terminals Installation types The transmitter was ordered and shipped to be installed in one of several possible configurations.
Page 328
Transmitter components and installation wiring Figure H-2: High-temperature meters with factory connection The transmitter is shipped with a flexible connection factory installed between the sensor and the transmitter. The transmitter must be dismounted from its shipping location (spot‐welded to the sensor case) and then mounted separately.
Page 329
Transmitter components and installation wiring Figure H-4: 4-wire remote installation for density and viscosity meters (CDM, FDM, or FVM with fieldbus only) The transmitter is installed remotely from the Compact Density Meter (CDM), Fork Density Meter (FDM), or Fork Viscosity Meter (FVM). The 4‐wire connection between the sensor and transmitter must be field wired. Power supply must be field wired to the transmitter.
Page 330
Transmitter components and installation wiring Figure H-5: 9-wire remote installation The transmitter and core processor are combined in a single unit that is installed remotely from the sensor. The 9‐wire connection between the transmitter/core processor and the sensor must be field wired. Power supply must be field wired to the transmitter.
Page 331
Transmitter components and installation wiring Figure H-6: Remote core processor with remote sensor installation The transmitter, core processor, and sensor are all mounted separately. The 4‐wire connection between the transmitter and core processor must be field wired. The 9‐wire connection between the core processor and the sensor must be field wired.
Page 332: Power Supply Terminals And Ground

Transmitter components and installation wiring Power supply terminals and ground Figure H-7: Power supply wiring terminals Warning flap Equipment ground Power supply wiring terminals (9 and 10) Fieldbus wiring terminals FOUNDATION Fieldbus Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 333: Appendix Ine53 History

NE53 history Appendix I NE53 history This document can be found at www.emerson.com. Operating instructions within this document are English versions. Instructions in other languages have different part numbers but matching revision letters. Operating Date Version Type Change instruction 09/2000…
Page 334
NE53 history Operating Date Version Type Change instruction Expansion • Software version information available either through the display or through Modbus • Totalizers can be disabled, in addition to starting and stopping • Doubled the number of virtual communication rela- tionshups (VCRs) Adjustment •…
Page 335
NE53 history Operating Date Version Type Change instruction 07/2012 Adjustment • Added DI channels to increment the Concentration 3600326 EB Mass Curve • Added Special units support for both Mass Flow and Volume Flow • Moved mass flow, volume flow, and density limit pa- rameters from the Device Info TB to the Measurement •…
Page 336
NE53 history Micro Motion Model 2700 Transmitters with FOUNDATION Fieldbus…
Page 337
NE53 history Configuration and Use Manual…
Page 338
© 2018 Micro Motion, Inc. All rights reserved. The Emerson logo is a trademark and service mark of Emerson Electric Co. Micro Motion, ELITE, ProLink, MVD and MVD Direct Connect marks are marks of one of the Emerson Automation Solutions family of companies. All other marks are property of their respective owners.

Источник

Contents
Table of Contents
Troubleshooting
Bookmarks

Quick Links

Configuration and Use Manual

MMI-20019048, Rev AB

March 2018

Micro Motion

Model 2700 Transmitters with

Intrinsically Safe Outputs

Configuration and Use Manual

Related Manuals for Emerson Micro Motion 2700

Summary of Contents for Emerson Micro Motion 2700

Page 1
Configuration and Use Manual MMI-20019048, Rev AB March 2018 ® Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs Configuration and Use Manual…
Page 2
Micro Motion employees. Micro Motion will not accept your returned equipment if you fail to follow Micro Motion procedures. Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion Customer Service department.
Page 3: Table Of Contents

Contents Contents Part I Getting started Chapter 1 Before you begin ………………….3 About this manual ……………………. 3 Transmitter model code …………………… 3 Communications tools and protocols ……………….. 4 Additional documentation and resources ………………4 Chapter 2 Quick start ……………………5 Power up the transmitter …………………..5 Check meter status ……………………5 2.2.1…
Page 4
Contents 4.5.2 Configure two-phase flow parameters …………….43 4.5.3 Configure Density Damping ………………45 4.5.4 Configure Density Cutoff ………………..46 Configure temperature measurement ………………47 4.6.1 Configure Temperature Measurement Unit …………..47 4.6.2 Configure Temperature Damping …………….48 4.6.3 Effect of Temperature Damping on process measurement ……….. 48 4.6.4 Configure Temperature Input ………………
Page 5
Contents Configure the transmitter channels ………………… 87 Configure the mA Output ………………….88 6.2.1 Configure mA Output Process Variable ……………. 88 6.2.2 Configure Lower Range Value (LRV) and Upper Range Value (URV) …….91 6.2.3 Configure AO Cutoff …………………93 6.2.4 Configure Added Damping ……………….94 6.2.5 Configure mA Output Fault Action and mA Output Fault Level ……..
Page 6
Contents Use Smart Meter Verification (SMV) ………………140 9.2.1 SMV requirements …………………. 140 9.2.2 SMV test preparation ………………..140 9.2.3 Run SMV ……………………141 9.2.4 View test data ………………….145 9.2.5 Schedule automatic execution of the SMV test …………149 Use PVR, TBR, and TMR ………………….152 9.3.1 PVR, TBR, and TMR applications ………………
Page 7
Contents 10.22 Check Frequency Output Fault Action ………………198 10.23 Check Flow Direction …………………… 199 10.24 Check the cutoffs ……………………199 10.25 Check for two-phase flow (slug flow) ………………199 10.26 Check the drive gain ……………………200 10.26.1 Collect drive gain data ………………..201 10.27 Check the pickoff voltage ………………….
Page 8
Contents Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 9: Part I Getting Started

Getting started Part I Getting started Chapters covered in this part: • Before you begin • Quick start Configuration and Use Manual…
Page 10
Getting started Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 11: Before You Begin

Before you begin Before you begin Topics covered in this chapter: • About this manual • Transmitter model code • Communications tools and protocols • Additional documentation and resources About this manual This manual helps you configure, commission, use, maintain, and troubleshoot Micro Motion Model 2700 transmitters with intrinsically safe outputs.
Page 12: Communications Tools And Protocols

Smart Wireless THUM Adapter. Use of AMS or the Smart Wireless THUM Adapter is not discussed in this manual. For more information on the Smart Wireless THUM Adapter, refer to the documentation available at www.emerson.com. Additional documentation and resources Topic…
Page 13: Chapter 2 Quick Start

Quick start Quick start Topics covered in this chapter: • Power up the transmitter • Check meter status • Make a startup connection to the transmitter • Verify mass flow measurement • Verify the zero Power up the transmitter The transmitter must be powered up for all configuration and commissioning tasks, or for process measurement.
Page 14: Transmitter Status Reported By Led

Quick start Wait approximately 10 seconds for the power-up sequence to complete. Immediately after power-up, the transmitter runs through diagnostic routines and checks for error conditions. During the power-up sequence, Alert A009 is active. This alert should clear automatically when the power-up sequence is complete. Check the status LED on the transmitter.
Page 15: Make A Startup Connection To The Transmitter

Quick start Make a startup connection to the transmitter For all configuration tools except the display, you must have an active connection to the transmitter to configure the transmitter. Identify the connection type to use, and follow the instructions for that connection type in the appropriate appendix.
Page 16: Terminology Used With Zero Verification And Zero Calibration

Quick start • The zero is required by site procedures. • The stored zero value fails the zero verification procedure. Procedure Allow the flowmeter to warm up for at least 20 minutes after applying power. Run the process fluid through the sensor until the sensor temperature reaches the normal process operating temperature.
Page 17
Quick start Term Definition Prior Zero The zero value stored in the transmitter at the time a field zero calibration is begun. May be the factory zero or a previous field zero. Manual Zero The zero value stored in the transmitter, typically obtained from a zero calibration procedure.
Page 18
Quick start Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 19: Part Ii Configuration And Commissioning

Configuration and commissioning Part II Configuration and commissioning Chapters covered in this part: • Introduction to configuration and commissioning • Configure process measurement • Configure device options and preferences • Integrate the meter with the control system Complete the configuration •…
Page 20
Configuration and commissioning Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 21: Introduction To Configuration And Commissioning

Introduction to configuration and commissioning Introduction to configuration and commissioning Topics covered in this chapter: • Configuration flowchart • Default values and ranges • Enable access to the off-line menu of the display • Disable write-protection on the transmitter configuration •…
Page 22
Introduction to configuration and commissioning Figure 3-1: Configuration flowchart Configure device options and Test and move to production Configure process measurement preferences Configure mass flow Test or tune transmitter Configure display measurement using sensor simulation parameters Configure volume flow meaurement Configure fault handling Back up transmitter parameters…
Page 23: Default Values And Ranges

Introduction to configuration and commissioning Default values and ranges Section D.1 to view the default values and ranges for the most commonly used parameters. Enable access to the off-line menu of the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY ProLink III Device Tools >…
Page 24: Set The Hart Lock

Introduction to configuration and commissioning Set the HART lock If you plan to use a HART connection to configure the device, you can lock out all other HART masters. If you do this, other HART masters will be able to read data from the device but will not be able to write data to the device.
Page 25
Introduction to configuration and commissioning Important You cannot restore factory configurations with a 700 core. Restoring the factory configuration is not a common action. You may want to contact customer support to see if there is a preferred method to resolve any issues. Configuration and Use Manual…
Page 26
Introduction to configuration and commissioning Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 27: Configure Process Measurement

Configure process measurement Configure process measurement Topics covered in this chapter: • Configure mass flow measurement • Configure volume flow measurement for liquid applications • Configure GSV flow measurement • Configure Flow Direction • Configure density measurement • Configure temperature measurement •…
Page 28
Configure process measurement If the measurement unit you want to use is not available, you can define a special measurement unit. Options for Mass Flow Measurement Unit The transmitter provides a standard set of measurement units for Mass Flow Measurement Unit, plus one user-defined special measurement unit.
Page 29
Configure process measurement Define a special measurement unit for mass flow Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure > Manual Setup > Measurements > Special Units > Mass Special Units Overview A special measurement unit is a user-defined unit of measure that allows you to report process data, totalizer data, and inventory data in a unit that is not available in the…
Page 30: Configure Flow Damping

Configure process measurement a. 1 lb/sec = 16 oz/sec b. Mass Flow Conversion Factor = 1 ÷ 16 = 0.0625 Set Mass Flow Conversion Factor to 0.0625. Set Mass Flow Label to oz/sec. Set Mass Total Label to oz. 4.1.2 Configure Flow Damping Display Not available…
Page 31: Configure Mass Flow Cutoff

Configure process measurement Effect of flow damping on volume measurement Flow damping affects volume measurement for liquid volume data. Flow damping also affects volume measurement for gas standard volume data. The transmitter calculates volume data from the damped mass flow data. Interaction between Flow Damping and mA Output Damping In some circumstances, both Flow Damping and mA Output Damping are applied to the…
Page 32: Configure Volume Flow Measurement For Liquid Applications

Configure process measurement Interaction between Mass Flow Cutoff and mA Output Cutoff Mass Flow Cutoff defines the lowest mass flow value that the transmitter will report as measured. mA Output Cutoff defines the lowest flow rate that will be reported via the mA output.
Page 33: Configure Volume Flow Type For Liquid Applications

Configure process measurement Restriction You cannot implement both liquid volume flow and gas standard volume flow at the same time. Choose one or the other. Note If you need to switch from gas standard volume to liquid volume, polling for base density will automatically be disabled.
Page 34
Configure process measurement Overview Volume Flow Measurement Unit specifies the unit of measurement that will be displayed for the volume flow rate. The unit used for the volume total and volume inventory is based on this unit. Prerequisites Before you configure Volume Flow Measurement Unit, be sure that Volume Flow Type is set to Liquid.
Page 35
Configure process measurement Label Unit description Display ProLink III Field Communicator l/hr Liters per hour MILL/D mil l/day ML/d Million liters per day UKGPS Imp gal/sec Impgal/s Imperial gallons per second UKGPM Imp gal/min Impgal/min Imperial gallons per minute Imperial gallons per hour UKGPH Imp gal/hr Impgal/h…
Page 36: Configure Volume Flow Cutoff

Configure process measurement Base Volume Unit is the existing volume unit that the special unit will be based on. Specify Base Time Unit. Base Time Unit is the existing time unit that the special unit will be based on. Calculate Volume Flow Conversion Factor as follows: a.
Page 37
Configure process measurement The default value for Volume Flow Cutoff is 0.0 l/sec (liters per second). The lower limit is Interaction between Volume Flow Cutoff and mAO Cutoff Volume Flow Cutoff defines the lowest liquid volume flow value that the transmitter will report as measured.
Page 38: Configure Gsv Flow Measurement

Configure process measurement Configure GSV flow measurement The gas standard volume (GSV) flow measurement parameters control how volume flow is measured and reported in a gas application. Restriction You cannot implement both liquid volume flow and gas standard volume flow at the same time. Choose one or the other.
Page 39
Configure process measurement Overview The Standard Density of Gas value is the gas density at standard reference conditions. Use it to convert the measured mass flow data to volume flow at reference conditions. Prerequisites Ensure that Density Measurement Unit is set to the measurement unit you want to use for Standard Density of Gas.
Page 40: Configure Gas Standard Volume Flow Unit

Configure process measurement Set Polling Control n as one of the following options: The n is the value you selected in the Polling Slot field. If there is another master, and if that master is primary, then set this field to secondary.
Page 41
Configure process measurement For polling, the first transmitter (master) requests density from a second transmitter (slave) via HART communications. Special units for GSV are allowed on the master side, but the device being polled (slave) cannot have special units set for density, otherwise the master will reject the base density and report an A115: No External Input or Polled Data Alert.
Page 42
Configure process measurement Label Unit description Display ProLink III Field Communicator SLPD SLPD SLPD Standard liters per day SPECL special Special Special measurement unit Define a special measurement unit for gas standard volume flow Display Not available ProLink III Device Tools > Configuration > Process Measurement > Flow > Special Units Field Communicator Configure >…
Page 43: Configure Gas Standard Volume Flow Cutoff

Configure process measurement The special measurement unit is stored in the transmitter. You can configure the transmitter to use the special measurement unit at any time. Example: Defining a special measurement unit for gas standard volume flow You want to measure gas standard volume flow in thousands of standard cubic feet per minute.
Page 44: Configure Flow Direction

Configure process measurement Gas Standard Volume Flow Cutoff affects both the gas standard volume flow values reported via outputs and the gas standard volume flow values used in other transmitter behavior (e.g., events defined on gas standard volume flow). mA Output Cutoff affects only flow values reported via the mA Output. Example: Cutoff interaction with mA Output Cutoff lower than Gas Standard Volume Flow Cutoff Configuration:…
Page 45: Options For Flow Direction

Configure process measurement Overview Flow Direction controls how forward flow and reverse flow affect flow measurement and reporting. Flow Direction is defined with respect to the flow arrow on the sensor: • Forward flow (positive flow) moves in the direction of the flow arrow on the sensor. •…
Page 46
Configure process measurement Effect of Flow Direction on mA Outputs Flow Direction affects how the transmitter reports flow values via the mA Outputs. The mA Outputs are affected by Flow Direction only if mA Output Process Variable is set to a flow variable.
Page 47
Configure process measurement Figure 4-2: Effect of Flow Direction on the mA Output: Lower Range Value < 0 Flow Direction = Forward Flow Direction = Reverse, Negate Forward Flow Direction = Absolute Value, Bidirectional, Negate Bidirectional Reverse flow Forward flow Reverse flow Forward flow Reverse flow…
Page 48
Configure process measurement • Under conditions of forward flow, for flow rates between 0 and +100 g/sec, the mA Output varies between 12 mA and 20 mA in proportion to (the absolute value of) the flow rate. • Under conditions of forward flow, if (the absolute value of) the flow rate equals or exceeds 100 g/sec, the mA Output is proportional to the flow rate up to 20.5 mA, and will be level at 20.5 mA at higher flow rates.
Page 49
Configure process measurement Table 4-1: Effect of the flow direction parameter and actual flow direction on Frequency Outputs (continued) Actual flow direction Flow Direction setting Forward Zero flow Reverse Negate Bidirectional Hz > 0 0 Hz Hz > 0 Effect of flow direction on Discrete Outputs The flow direction parameter affects the Discrete Output behavior only if Discrete Output Source is set to Flow Direction.
Page 50: Configure Density Measurement

Configure process measurement Table 4-3: Effect of the flow direction on flow values (continued) Actual flow direction Flow Direction setting Forward Zero flow Reverse Negate Bidirectional Negative Positive (1) Refer to the digital communications status bits for an indication of whether flow is positive or negative. Effect of flow direction on flow totals Flow direction affects how flow totals and inventories are calculated.
Page 51: Configure Two-Phase Flow Parameters

Configure process measurement Options for Density Measurement Unit The transmitter provides a standard set of measurement units for Density Measurement Unit. Different communications tools may use different labels. Label Unit description Display ProLink III Field Communicator Specific gravity Grams per cubic centimeter G/CM3 g/cm3 g/Cucm…
Page 52
Configure process measurement Gas entrainment can cause your process density to drop temporarily. To reduce the occurrence of two-phase flow alerts that are not significant to your process, set Two-Phase Flow Low Limit slightly below your expected lowest process density. You must enter Two-Phase Flow Low Limit in g/cm³, even if you configured another unit for density measurement.
Page 53: Configure Density Damping

Configure process measurement If Two-Phase Flow Timeout is set to 0.0 seconds, the outputs that represent flow rate will report a flow rate of 0 as soon as two-phase flow is detected. 4.5.3 Configure Density Damping Display Not available ProLink III Device Tools >…
Page 54: Configure Density Cutoff

Configure process measurement The value you enter is automatically rounded off to the nearest valid value. The valid values for Density Damping depend on the setting of Update Rate. Update Rate setting Valid damping values Normal 0.0, 0.2, 0.4, 0.8, 1.6, 3.2, 6.4, 12.8, 25.6, 51.2 Special 0.0, 0.04, 0.08, 0.16, 0.32, 0.64, 1.28, 2.56, 5.12, 10.24, 20.48, 40.96…
Page 55: Configure Temperature Measurement

Configure process measurement Effect of Density Cutoff on volume measurement Density Cutoff affects liquid volume measurement. If the density value goes below Density Cutoff, the volume flow rate is reported as 0. Density Cutoff does not affect gas standard volume measurement. Gas standard volume values are always calculated from the value configured for Standard Gas Density or polled value if configured for polled base density.
Page 56: Configure Temperature Damping

Configure process measurement 4.6.2 Configure Temperature Damping Display Not available ProLink III Device Tools > Configuration > Temperature Field Communicator Configure > Manual Setup > Measurements > Temperature > Temp Damping Overview Temperature Damping controls the amount of damping that will be applied to the line temperature value, when the on-board temperature data is used (RTD).
Page 57: Configure Temperature Input

Configure process measurement Temperature compensation Temperature compensation adjusts process measurement to compensate for the effect of temperature on the sensor tubes. Petroleum measurement Temperature Damping affects petroleum measurement process variables only if the transmitter is configured to use temperature data from the sensor. If an external temperature value is used for petroleum measurement, Temperature Damping does not affect petroleum measurement process variables.
Page 58
Configure process measurement Prerequisites You will need API documentation for the API table that you select. Depending on your API table, you may need to know the thermal expansion coefficient (TEC) for your process fluid. You must know the reference temperature that you want to use. Procedure Choose Device Tools >…
Page 59: Set Up Temperature Data For Petroleum Measurement Using Prolink Iii

Configure process measurement b. Verify that the referred density range of the selected table is adequate for your application. If you chose a C table, enter Thermal Expansion Coefficient (TEC) for your process fluid. Set Reference Temperature to the temperature to which density will be corrected in referred density calculations.
Page 60: Configure Petroleum Measurement Using The Field Communicator

Configure process measurement Option Description Setup Polling The meter polls an external de- a. Set Line Temperature Source to Poll for External Value. vice for temperature data. This b. Set Polling Slot to an available slot. data will be available in addi- c.
Page 61
Configure process measurement a. Open the Petroleum Measurement Source menu and select the API table number. Depending on your choice, you may be prompted to enter a reference temperature or a thermal expansion coefficient. b. Enter the API table letter. These two parameters uniquely specify the API table.
Page 62: Api Tables Supported By The Petroleum Measurement Application

Configure process measurement 4.7.4 API tables supported by the petroleum measurement application The API tables listed here are supported by the petroleum measurement application. Table name Process fluid CTL source data Reference temperature Density unit Generalized crude and Observed density and 60 °F (non-configurable) Degrees API observed temperature…
Page 63: Set Up Concentration Measurement

Configure process measurement Restriction These tables are not appropriate for the following process fluids: propane and propane mixes, butane and butane mixes, butadiene and butadiene mixes, isopentane, LNG, LPG, NGL, ethylene, propylene, cyclohexane, aeromatics, asphalts, and road tars. Set up concentration measurement This section guides you through loading and setting up a concentration matrix used for measurement.
Page 64
Configure process measurement Important • All concentration matrices on your transmitter must use the same derived variable. If you are using one of the standard matrices from Micro Motion, set Derived Variable to Mass Concentration (Density). If you are using a custom matrix, see the reference information for your matrix.
Page 65: Configure Concentration Measurement Using The Field Communicator

Configure process measurement Set Temperature Source to the method that the transmitter will use to obtain temperature data. Option Description The transmitter will poll an external temperature device, us- Poll for external value ing HART protocol over the primary mA output. The transmitter will use the temperature data from the sen- sor.
Page 66
Configure process measurement Choose Online > Configure > Manual Setup > Measurements > Temperature and set Temperature Unit to match the temperature unit used by your matrix. Choose Online > Configure > Manual Setup > Measurements and click Concentration Measurement. Enable or disable matrix switching, as desired.
Page 67: Standard Matrices For The Concentration Measurement Application

Configure process measurement Option Setup A user-configured a. Choose Online > Configure > Manual Setup > Measurements . static temperature b. Click External Inputs. value c. Click Next. d. Enable External Temperature. e. Set Correction Temperature to the value to be used. Polling for tempera- a.
Page 68: Derived Variables And Calculated Process Variables

Configure process measurement If the standard matrices are not appropriate for your application, you can build a custom matrix or purchase a custom matrix from Micro Motion. Temperature Matrix name Description Density unit unit Derived variable Deg Balling °F Mass Concentration Matrix represents percent extract, by g/cm (Density)
Page 69
Configure process measurement Calculated process variables Density at reference Standard Derived tempera- volume Specific Concen- Net mass volume Variable Description ture flow rate gravity tration flow rate flow rate ✓ ✓ Density Mass/unit volume, cor- at Reference rected to a given refer- ence temperature ✓…
Page 70: Configure Pressure Compensation

Not all sensors or applications require pressure compensation. The pressure effect for a specific sensor model can be found in the product data sheet located at www.emerson.com. If you are uncertain about implementing pressure compensation, contact customer service. Prerequisites You will need the flow factor, density factor, and calibration pressure values for your sensor.
Page 71
Configure process measurement The calibration pressure is the pressure at which your sensor was calibrated, and defines the pressure at which there is no pressure effect. If the data is unavailable, enter 20 PSI. Enter Flow Factor for your sensor. The flow factor is the percent change in the flow rate per PSI.
Page 72: Configure Pressure Compensation Using The Field Communicator

Configure process measurement If you want to use digital communications, click Apply, then perform the necessary host programming and communications setup to write pressure data to the transmitter at appropriate intervals. Postrequisites If you are using an external pressure value, verify the setup by checking the External Pressure value displayed in the Inputs area of the main window.
Page 73: Options For Pressure Measurement Unit

Configure process measurement Option Setup Polling for pressure a. Ensure that the primary mA Output has been wired to support HART polling. b. Choose Online > Configure > Manual Setup > Measurements > External Pressure/Temperature > External Polling . c. Set Poll Control to Poll As Primary Host or Poll as Secondary Host. d.
Page 74
Configure process measurement Label Unit description Display ProLink III Field Communicator mBAR millibar mbar Millibar G/SCM g/cm2 g/Sqcm Grams per square centimeter KG/SCM kg/cm2 kg/Sqcm Kilograms per square centimeter Pascals pascals Kilopascals Kilopascals Megapascals Megapascals Torr @ 0 °C TORR Torr @ 0°C torr Atmospheres…
Page 75: Configure Device Options And Preferences

Configure device options and preferences Configure device options and preferences Topics covered in this chapter: • Configure the transmitter display • Enable or disable operator actions from the display • Configure security for the display menus • Configure response time parameters •…
Page 76
Configure device options and preferences Overview You can control the process variables and diagnostic variables shown on the display, and the order in which they appear. The display can scroll through up to 15 variables in any order you choose. In addition, you can repeat variables or leave slots unassigned. Restrictions •…
Page 77: Configure The Number Of Decimal Places (Precision) Shown On The Display

Configure device options and preferences Configure Display Variable 1 to track the primary mA Output Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLY > VAR 1 ProLink III Device Tools > Configuration > Transmitter Display > Display Security Field Communicator Not available Overview You can configure Display Variable 1 to track mA Output Process Variable for the primary mA Output.
Page 78: Configure The Refresh Rate Of Data Shown On The Display

Configure device options and preferences For temperature and density process variables, the default value is 2 decimal places. For all other variables, the default value is 4 decimal places. The range is 0 to 5. The lower the precision, the greater the change must be for it to be reflected on the display. Do not set the precision too low or too high to be useful.
Page 79: Enable Or Disable The Display Backlight

Configure device options and preferences Option Description Disabled (de- The display shows Display Variable 1 and does not scroll automatically. The operator can move to the next display variable at any time using Scroll. fault) If you enabled Auto Scroll, set Scroll Rate as desired. The default value is 10 seconds.
Page 80: Enable Or Disable Operator Actions From The Display

Configure device options and preferences Enable or disable operator actions from the display You can configure the transmitter to let the operator perform specific actions using the display. • Enable or disable Totalizer Start/Stop from the display (Section 5.2.1) • Enable or disable Totalizer Reset from the display (Section 5.2.2) •…
Page 81: Enable Or Disable Totalizer Reset From The Display

Configure device options and preferences 5.2.2 Enable or disable Totalizer Reset from the display Display OFF-LINE MAINT > OFF-LINE CONFG > DISPLAY > TOTALS RESET ProLink III Device Tools > Configuration > Totalizer Control Methods Field Communicator Configure > Manual Setup > Display > Display Variable Menu Features > Totalizer Reset Overview You can configure whether or not the operator is able to reset totalizers from the display.
Page 82: Configure Security For The Display Menus

Configure device options and preferences Procedure Ensure that the alert menu is accessible from the display. To acknowledge alerts from the display, operators must have access to the alert menu. Enable or disable Acknowledge All Alerts as desired. Option Description Enabled (default) Operators can use a single display command to acknowledge all alerts at once.
Page 83: Configure Response Time Parameters

Configure device options and preferences Option Description Disabled Operator cannot access the alert menu. Note The transmitter status LED changes color to indicate that there are active alerts, but does not show specific alerts. To require a password for access to the maintenance section of the off-line menu and the Smart Meter Verification menu, enable or disable Off-Line Password.
Page 84: Configure Update Rate

Configure device options and preferences 5.4.1 Configure Update Rate Display Not available ProLink III Device Tools > Configuration > Process Measurement > Response > Update Rate Field Communicator Configure > Manual Setup > Measurements > Update Rate Overview Update Rate controls the rate at which process data is polled and process variables are calculated.
Page 85
Configure device options and preferences Effects of Update Rate = Special Incompatible features and functions Special mode is not compatible with the following features and functions: • Enhanced events. Use basic events instead. • All calibration procedures. • Zero verification. •…
Page 86: Configure Response Time

Configure device options and preferences 5.4.2 Configure Response Time Display Not available ProLink III Device Tools > Configuration > Process Measurement > Response > Response Time Field Communicator Not available Overview Response Time is used to apply a different algorithm to the calculation of process variables from the raw process data.
Page 87: Configure Fault Timeout

Configure device options and preferences 5.5.1 Configure Fault Timeout Display Not available ProLink III Device Tools > Configuration > Fault Processing Field Communicator Configure > Alert Setup > Alert Severity > Fault Timeout Overview Fault Timeout controls the delay before fault actions are performed. Restriction Fault Timeout is applied only to the following alerts (listed by Status Alert Code): A003, A004, A005, A008, A016, A017, A033.
Page 88
Configure device options and preferences Use the default settings for Status Alert Severity unless you have a specific requirement to change them. Procedure Select a status alert. For the selected status alert, set Status Alert Severity as desired. Option Description Fault Actions when fault is detected: •…
Page 89
Configure device options and preferences Table 5-2: Status alerts and Status Alert Severity (continued) Alert code Status message Default severity Notes Configurable? Fault A009 Transmitter Initializing/ Warming Up A010 Calibration Failure Fault A011 Zero Calibration Failed: Fault A012 Zero Calibration Failed: Fault High Fault…
Page 90
Configure device options and preferences Table 5-2: Status alerts and Status Alert Severity (continued) Alert code Status message Default severity Notes Configurable? Meter Verification Aborted Fault A035 Applies only to transmitters with Smart Meter Verification. A100 mA Output 1 Saturated Informational Can be set to either Informational or Ignore, but cannot be set to Fault.
Page 91: Configure Informational Parameters

Configure device options and preferences Table 5-2: Status alerts and Status Alert Severity (continued) Alert code Status message Default severity Notes Configurable? Informational A121 Extrapolation Alarm (Con- Applies only to transmitters with centration) the concentration measurement application. A131 Meter Verification in Pro- Informational Applies only to transmitters with gress: Outputs to Last…
Page 92: Configure Sensor Material

Configure device options and preferences 5.6.2 Configure Sensor Material Display Not available ProLink III Device Tools > Configuration > Informational Parameters > Sensor Field Communicator Configure > Manual Setup > Info Parameters > Sensor Information > Tube Wetted Mate- rial Overview Sensor Material lets you store the type of material used for your sensor’s wetted parts in transmitter memory.
Page 93: Configure Descriptor

Configure device options and preferences Overview Sensor Flange Type lets you store your sensor’s flange type in transmitter memory. This parameter is not used in processing and is not required. Procedure Obtain your sensor’s flange type from the documents shipped with your sensor, or from a code in the sensor model number.
Page 94: Configure Date

Configure device options and preferences 5.6.7 Configure Date Display Not available ProLink III Device Tools > Configuration > Informational Parameters > Transmitter Field Communicator Configure > Manual Setup > Info Parameters > Transmitter Info > Date Overview Date lets you store a static date (not updated by the transmitter) in transmitter memory. This parameter is not used in processing and is not required.
Page 95: Integrate The Meter With The Control System

Integrate the meter with the control system Integrate the meter with the control system Topics covered in this chapter: • Configure the transmitter channels • Configure the mA Output • Configure the Frequency Output • Configure the Discrete Output • Configure events •…
Page 96: Configure The Ma Output

Integrate the meter with the control system Postrequisites For each channel that you configured, perform or verify the corresponding input or output configuration. When the configuration of a channel is changed, the channel’s behavior will be controlled by the configuration that is stored for the selected input or output type, and the stored configuration may not be appropriate for your process.
Page 97
Integrate the meter with the control system • If you are using the HART variables, be aware that changing the configuration of mA Output Process Variable will change the configuration of the HART Primary Variable (PV). • If you are using the HART variables, be aware that changing the configuration of mA Output Process Variable will change the configuration of the HART Primary Variable (PV) and/or the HART Secondary Variable (SV).
Page 98
Integrate the meter with the control system Table 6-2: Petroleum measurement mA Output process variables Label Process variable Display ProLink III Field Communicator Average corrected density AVE D Average Density TC Avg Dens Average temperature AVE T Average Temperature TC Avg Temp Temperature-corrected TCVOL Volume Flow Rate at Reference…
Page 99: Configure Lower Range Value (Lrv) And Upper Range Value (Urv)

Integrate the meter with the control system Table 6-5: PVR mA Output process variables (continued) Label Process variable Display ProLink III Field Communicator Corrected water flow WTR60 Water Flow Rate At Reference Water Flow Rate at Reference Shrinkage factor corrected SFOIL SF Oil Flow Rate At Line Shrinkage Factor Oil Flow Rate…
Page 100
Integrate the meter with the control system Ensure that the measurement unit for the configured process variable has been set as desired. Procedure Set LRV and URV as desired. • LRVis the value of mA Output Process Variable represented by an output of 4 mA. The default value for LRV depends on the setting of mA Output Process Variable.
Page 101: Configure Ao Cutoff

Integrate the meter with the control system Table 6-6: Default values for Lower Range Value (LRV) and Upper Range Value (URV) (continued) Process variable Concentration 100% Baume Specific gravity 6.2.3 Configure AO Cutoff Display Not available ProLink III Device Tools > Configuration > I/O > Outputs > mA Output Field Communicator •…
Page 102: Configure Added Damping

Integrate the meter with the control system Example: Cutoff interaction Configuration: • mA Output Process Variable = Mass Flow Rate • Frequency Output Process Variable = Mass Flow Rate • AO Cutoff = 10 g/sec • Mass Flow Cutoff = 15 g/sec Result: If the mass flow rate drops below 15 g/sec, all outputs representing mass flow will report zero flow.
Page 103
Integrate the meter with the control system Added Damping affects the reporting of mA Output Process Variable through the mA Output only. It does not affect the reporting of that process variable via any other method (e.g., a Frequency Output or digital communications), or the value of the process variable used in calculations.
Page 104: Configure Ma Output Fault Action And Ma Output Fault Level

Integrate the meter with the control system • mA Output Damping = 2 seconds Result: A change in the mass flow rate will be reflected in the mA Output over a time period that is greater than 3 seconds. The exact time period is calculated by the transmitter according to internal algorithms which are not configurable.
Page 105: Configure The Frequency Output

Integrate the meter with the control system Options for mA Output Fault Action and mA Output Fault Level Option mA Output behavior mA Output Fault Level Upscale Goes to the configured fault level Default: 22.0 mA Range: 21.0 to 24.0 mA Downscale (default) Goes to the configured fault level Default: 3.2 mA…
Page 106
Integrate the meter with the control system Prerequisites If you plan to configure the output to report volume flow, ensure that you have set Volume Flow Type as desired: Liquid or Gas Standard Volume. If you plan to configure an output to report a concentration measurement process variable, ensure that the concentration measurement application is configured so that the desired variable is available.
Page 107: Configure Frequency Output Polarity

Integrate the meter with the control system Table 6-10: Concentration measurement FO process variables (continued) Label Process variable Display ProLink III Field Communicator Standard volume flow rate STD V Volume Flow Rate at Reference ED Std Vol flo Temperature Table 6-11: Fuel consumption FO process variables Label Process variable…
Page 108: Configure Frequency Output Scaling Method

Integrate the meter with the control system Polarity option Reference voltage (OFF) Pulse voltage (ON) Active Low As determined by power supply, pull-up resistor, and load. See the installation manual for your transmitter. 6.3.3 Configure Frequency Output Scaling Method Display OFF-LINE MAINT >…
Page 109: Configure Frequency Output Fault Action And Frequency Output Fault Level

Integrate the meter with the control system If you specify Frequency=Flow, you must provide values for Rate Factor and Frequency Factor: Rate Factor The maximum flow rate that you want the Frequency Output to report. Frequency A value calculated as follows: Factor RateFactor FrequencyFactor =…
Page 110: Configure The Discrete Output

Integrate the meter with the control system The default value is 15000 Hz. The range is 10 to 15000 Hz. Options for Frequency Output Fault Action Table 6-12: Options for Frequency Output Fault Action Label Frequency Output behavior Upscale Goes to configured Upscale value: •…
Page 111: Configure Discrete Output Source

Integrate the meter with the control system 6.4.1 Configure Discrete Output Source Display OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET DO > DO SRC ProLink III Device Tools > Configuration > I/O > Outputs > Discrete Output Field Communicator Configure >…
Page 112
Integrate the meter with the control system Important If you assign Flow Switch to the Discrete Output, you should also configure Flow Switch Variable, Flow Switch Setpoint, and Hysteresis. Related information Configure an enhanced event Fault indication with the Discrete Output Configure Flow Switch parameters Display OFF-LINE MAINT >…
Page 113: Configure Discrete Output Polarity

Integrate the meter with the control system 6.4.2 Configure Discrete Output Polarity Display OFF-LINE MAINT > OFF-LINE CONFG > IO > CH B > SET DO > DO POLAR ProLink III Device Tools > Configuration > I/O > Outputs > Discrete Output Field Communicator Configure >…
Page 114: Configure Events

Integrate the meter with the control system Note For some faults only: If Fault Timeout is set to a non-zero value, the transmitter will not implement the fault action until the timeout has elapsed. CAUTION! Do not use Discrete Output Fault Action as a fault indicator. If you do, you may not be able to distinguish a fault condition from a normal operating condition.
Page 115: Configure A Basic Event

Integrate the meter with the control system • Enhanced event model 6.5.1 Configure a basic event Display Not available ProLink III Device Tools > Configuration > Events > Basic Events Field Communicator Not available Overview A basic event is used to provide notification of process changes. A basic event occurs (is ON) if the real-time value of a user-specified process variable moves above (HI) or below (LO) a user-defined setpoint.
Page 116
Integrate the meter with the control system Overview An enhanced event is used to provide notification of process changes and, optionally, to perform specific transmitter actions if the event occurs. An enhanced event occurs (is ON) if the real-time value of a user-specified process variable moves above (HI) or below (LO) a user-defined setpoint, or in range (IN) or out of range (OUT) with respect to two user- defined setpoints.
Page 117: Configure Digital Communications

Integrate the meter with the control system Options for Enhanced Event Action Label Action Display ProLink III Field Communicator Standard None (default) NONE None None Start sensor zero START ZERO Start Sensor Zero Perform auto zero Start/stop all totalizers START STOP Start/Stop All Totalization Start/stop totals Reset mass total…
Page 118: Configure Hart/Bell 202 Communications

Integrate the meter with the control system Note The service port responds automatically to a wide range of connection requests. It is not configurable. 6.6.1 Configure HART/Bell 202 communications HART/Bell 202 communications parameters support HART communications with the transmitter’s primary mA terminals over a HART/Bell 202 network. Configure basic HART parameters Basic HART parameters include the HART address, HART tags, and the operation of the primary mA Output.
Page 119
Integrate the meter with the control system Important If you use ProLink III to set HART Address to 0, the program automatically enables mA Output Action. If you use ProLink III to set HART Address to any other value, the program automatically disables mA Output Action.
Page 120
Integrate the meter with the control system • If you set Burst Mode Output to send four user-specified variables, set the four process variables to be sent in each burst. • If you set Burst Mode Output to any other option, ensure that the HART variables are set as desired.
Page 121
Integrate the meter with the control system Table 6-13: Standard HART process variables (continued) Process variable Primary Varia- Secondary Third Variable Fourth Varia- ble (PV) Variable (SV) (TV) ble (QV ) ✓ Mass Inventory ✓ Mass Total ✓ Meter Temperature (T-Series) ✓…
Page 122
Integrate the meter with the control system Table 6-15: Concentration measurement HART process variables (continued) Process variable Primary Varia- Secondary Third Variable Fourth Varia- ble (PV) Variable (SV) (TV) ble (QV ) ✓ CM Standard Volume Total Table 6-16: Fuel consumption HART process variables Process variable Primary Varia- Secondary…
Page 123
Integrate the meter with the control system Table 6-18: TMR-only HART process variables Process variable Primary Varia- Secondary Third Variable Fourth Varia- ble (PV) Variable (SV) (TV) ble (QV ) ✓ ✓ ✓ Remediated Mass Flow ✓ Remediated Mass Total ✓…
Page 124: Configure Digital Communications Fault Action

Integrate the meter with the control system 6.6.2 Configure Digital Communications Fault Action Display Not available ProLink III Device Tools > Configuration > Fault Processing Field Communicator Configure > Alert Setup > I/O Fault Actions > Comm Fault Action Overview Digital Communications Fault Actionspecifies the values that will be reported via digital communications if the device encounters an internal fault condition.
Page 125
Integrate the meter with the control system Label ProLink III Field Communicator Description Not a Number Not-a-Number • Process variables are reported as IEEE NAN. • Drive gain is reported as measured. • Modbus scaled integers are reported as Max Int.
Page 126
Integrate the meter with the control system Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 127: Complete The Configuration

Complete the configuration Complete the configuration Topics covered in this chapter: • Test or tune the system using sensor simulation • Back up transmitter configuration • Enable write-protection on the transmitter configuration Test or tune the system using sensor simulation Use sensor simulation to test the system’s response to a variety of process conditions, including boundary conditions, problem conditions, or alert conditions, or to tune the loop.
Page 128: Sensor Simulation

Complete the configuration Option Required values Sine Period Minimum Maximum For density, set Wave Form as desired and enter the required values. Option Required values Fixed Fixed Value Sawtooth Period Minimum Maximum Sine Period Minimum Maximum For temperature, set Wave Form as desired and enter the required values. Option Required values Fixed…
Page 129: Back Up Transmitter Configuration

Complete the configuration • All mass flow rate, temperature, and density values displayed or reported via outputs or digital communications • The mass total and mass inventory values • All volume calculations and data, including reported values, volume totals, and volume inventories •…
Page 130
Complete the configuration Overview If the transmitter is write-protected, the configuration is locked and nobody can change it until it is unlocked. This prevents accidental or unauthorized changes to the transmitter configuration parameters. Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 131: Part Iii Operations, Maintenance, And Troubleshooting

Operations, maintenance, and troubleshooting Part III Operations, maintenance, and troubleshooting Chapters covered in this part: • Transmitter operation • Measurement support • Troubleshooting Configuration and Use Manual…
Page 132
Operations, maintenance, and troubleshooting Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 133: Chapter 8 Transmitter Operation

Transmitter operation Transmitter operation Topics covered in this chapter: • Record the process variables • View process variables • View transmitter status using the status LED • View and acknowledge status alerts • Read totalizer and inventory values • Start and stop totalizers and inventories •…
Page 134: View Process Variables

Transmitter operation View process variables Display Scroll to the desired process variable. If AutoScroll is enabled, you can wait until the process variable is displayed. See Section 8.2.1 for more information. ProLink III View the desired variable on the main screen under Process Variables. See Section 8.2.2 for more information.
Page 135: View Process Variables And Other Data Using Prolink Iii

Transmitter operation Figure 8-1: Transmitter display features A. Status LED B. Display (LCD panel) C. Process variable D. Scroll optical switch E. Optical switch indicator: turns red when either Scroll or Select is activated F. Select optical switch G. Unit of measure for process variable H.
Page 136: View Transmitter Status Using The Status Led

Transmitter operation • To view a more complete set of process variables, plus the current state of the outputs, choose Service Tools > Variables. View transmitter status using the status LED The status LED shows the current alert condition of the transmitter. The status LED is located on the face of the transmitter.
Page 137: View And Acknowledge Status Alerts

Transmitter operation Table 8-1: Transmitter status reported by status LED (continued) LED state Description Recommendation Flashing red (if ena- One or more high-severity alerts are active A high-severity alert condition affects meas- bled) and have not been acknowledged. urement accuracy and output behavior. Re- solve the alert condition before continuing.
Page 138
Transmitter operation Figure 8-2: Using the display to view and acknowledge the status alerts Scroll and Select simultaneously for 4 seconds SEE ALARM Select Is ACK ALL enabled? ACK ALL Select Scroll EXIT Select Scroll Active/ unacknowledged alarms? Alarm code NO ALARM Scroll Select…
Page 139: View And Acknowledge Alerts Using Prolink Iii

Transmitter operation Postrequisites • To clear the following alerts, you must correct the problem, acknowledge the alert, then power-cycle the transmitter: A001, A002, A010, A011, A012, A013, A018, A019, A022, A023, A024, A025, A028, A029, A031. • For all other alerts: If the alert is inactive when it is acknowledged, it will be removed from the list.
Page 140: View Alerts Using The Field Communicator

Transmitter operation If the alert is active when it is acknowledged, it will be removed from the list when the alert condition clears. Related information Alert data in transmitter memory 8.4.3 View alerts using the Field Communicator You can view a list containing all alerts that are active, or inactive but unacknowledged. •…
Page 141: Read Totalizer And Inventory Values

Transmitter operation Transmitter action if condition occurs Alert data structure Contents Clearing Recent Alerts 50 most recent alert postings or alert clearings Not cleared; maintained across transmitter power cycles Read totalizer and inventory values Display To read a totalizer or inventory value from the display, it must be configured as a display variable.
Page 142: Start And Stop Totalizers And Inventories Using The Display

Transmitter operation Important Totalizers and inventories are started or stopped as a group. When you start any totalizer, all other totalizers and all inventories are started simultaneously. When you stop any totalizer, all other totalizers and all inventories are stopped simultaneously. You cannot start or stop inventories directly.
Page 143: Reset Totalizers

Transmitter operation Reset totalizers Display Section 8.7.1. ProLink III Device Tools > Totalizer Control > Totalizer and Inventories > Reset Mass Total Device Tools > Totalizer Control > Totalizer and Inventories > Reset Volume Total Device Tools > Totalizer Control > Totalizer and Inventories > Reset Gas Total Device Tools >…
Page 144: Reset Inventories

Transmitter operation Reset and Yes? alternately flash beneath the current totalizer value. 5. Select again to confirm. 6. Scroll to EXIT. 7. Select. • To reset the volume totalizer: 1. Scroll until the volume totalizer value appears. 2. Select. Exit displays beneath the current totalizer value. 3.
Page 145
Transmitter operation Overview When you reset an inventory, the transmitter sets its value to 0. It does not matter whether the inventory is started or stopped. If the inventory is started, it continues to track process measurement. Mass and volume inventory totals cannot be set separately. They can only be reset together simultaneously.
Page 146
Transmitter operation Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 147: Chapter 9 Measurement Support

Measurement support Measurement support Topics covered in this chapter: • Options for measurement support • Use Smart Meter Verification (SMV) • Use PVR, TBR, and TMR • Piecewise linearization (PWL) for calibrating gas meters • Use the fuel consumption application •…
Page 148: Use Smart Meter Verification (Smv)

Measurement support Use Smart Meter Verification (SMV) You can run an SMV test, view and interpret the results, and set up automatic execution. 9.2.1 SMV requirements To use SMV, the transmitter must be paired with an enhanced core processor. Table 9-1 for the minimum version of the transmitter, enhanced core processor, and communication tool needed to support SMV.
Page 149: Run Smv

Measurement support SMV has an output mode called Continuous Measurement that allows the transmitter to keep measuring while the test is in progress. If you choose to run the test in Last Measured Value or Fault modes instead, the transmitter outputs will be held constant for the two minute duration of the test.
Page 150
Measurement support Option Description Last Value During the test, all outputs will report the last measured value of their as- signed process variable. The test will run for approximately 140 seconds. While the test is in progress, dots traverse the display and test progress is shown. Postrequisites View the test results and take any appropriate actions.
Page 151
Measurement support SMV flowchart: Running a test using the display Figure 9-2: Running an SMV test using the display RUN VERFY Select OUTPUTS EXIT Scroll Select CONTINUE MEASR FAULT LAST VALUE EXIT Scroll Scroll Scroll Select Select Select ARE YOU SURE/YES? Select .
Page 152
Measurement support You may need to wait a few seconds while ProLink III synchronizes its database with the transmitter data. Enter any desired information on the Test Definition screen, and click Next. All information on this screen is optional. Choose the desired output behavior. Option Description Continue Measur-…
Page 153: View Test Data

Measurement support Postrequisites View the test results and take any appropriate actions. 9.2.4 View test data You can view the results of the current test. You can also view results from previous tests. Important You can view previous test results and see detailed test reports only if SMV is licensed. The transmitter stores the following information about the previous twenty SMV tests: •…
Page 154
Measurement support Figure 9-3: SMV – Top-level menu Scroll and Select simultaneously for 4 seconds Scroll ENTER METER VERFY Select RUN VERFY RESULTS READ SCHEDULE VERFY EXIT Scroll Scroll Scroll Select Select Select Scroll Select b. Scroll to Results Read and press Select. The runcount of the most recent test is displayed.
Page 155
Measurement support SMV flowchart: Viewing test results using the display Figure 9-4: Viewing SMV test results using the display RESULTS READ Select RUNCOUNT x Select Scroll Pass Result type Abort Fail xx HOURS xx HOURS xx HOURS Select Select Select PASS FAIL Abort Type…
Page 156
Measurement support Procedure Choose Device Tools > Diagnostics > Meter Verification and click Previous Test Results. The chart shows test results for all tests stored in the ProLink III database. (Optional) Click Next to view and print a test report. (Optional) Click Export Data to CSV File to save the data to a file on your PC.
Page 157: Schedule Automatic Execution Of The Smv Test

Measurement support Table 9-3: SMV abort codes Code Description Recommended actions User-initiated abort None required. Wait 15 seconds before starting an- other test. Frequency drift Ensure that temperature, flow, and density are sta- ble, and rerun the test. High drive gain Ensure that flow is stable, minimize entrained gas, and rerun the test.
Page 158
Measurement support Figure 9-5: SMV – Top-level menu Scroll and Select simultaneously for 4 seconds Scroll ENTER METER VERFY Select RUN VERFY RESULTS READ SCHEDULE VERFY EXIT Scroll Scroll Scroll Select Select Select Scroll Select Scroll to Schedule Verfy and press Select. To schedule a single test or the first test in recurring execution: a.
Page 159
Measurement support SMV flowchart: Scheduling test execution using the display Figure 9-6: Scheduling SMV test execution using the display SCHEDULE VERFY Select Schedule set? SCHED IS OFF TURN OFF SCHED/YES? Scroll Scroll Select Schedule deleted HOURS LEFT Scroll Select xx HOURS Select SET NEXT SET RECUR…
Page 160: Use Pvr, Tbr, And Tmr

Measurement support To schedule recurring execution, specify a value for Hours Between Recurring Runs. To disable scheduled execution: • To disable execution of a single scheduled test, set Hours Until Next Run to 0. • To disable recurring execution, set Hours Between Recurring Runs to 0. •…
Page 161: Pvr, Tbr, And Tmr Applications

Measurement support 9.3.1 PVR, TBR, and TMR applications PVR, TBR, and TMR are applications designed to provide more accurate process data in the presence of multiple phases. For example, if bubbles are present in the process fluid, or the process fluid is flashing, the volume measurements are often incorrect. Production Volume Reconciliation (PVR) •…
Page 162: Piecewise Linearization (Pwl) For Calibrating Gas Meters

PWL does not apply when measuring liquid flow. When better accuracy is required over the published gas measurement specifications, an Emerson-approved independent gas laboratory can calibrate gas up to 10 PWL adjustment points.
Page 163: Zero The Meter

Measurement support Standard process variables Standard and differential process variables Supply transmitter Return transmitter HART cable Engine Supply sensor Return sensor Storage tank Zero the meter Zeroing the meter establishes a baseline for process measurement by analyzing the sensor’s output when there is no flow through the sensor tubes. Prerequisites Verify the zero and prepare the meter using the procedures in Section…
Page 164: Validate The Meter

Measurement support Tool Path Field Communicator Service Tools > Maintenance > Zero Calibration > Perform Auto Zero If necessary, modify Zero Time. Zero Time controls the amount of time the transmitter takes to determine its zero-flow reference point. The default Zero Time is 20 seconds. For most applications, the default Zero Time is appropriate.
Page 165
Measurement support Important To adjust volume flow, you must set the meter factor for volume flow. Setting a meter factor for mass flow and a meter factor for density will not produce the desired result. The volume flow calculations are based on original mass flow and density values, before the corresponding meter factors have been applied.
Page 166: Alternate Method For Calculating The Meter Factor For Volume Flow

Measurement support The new meter factor for mass flow is 0.9996. 9.7.1 Alternate method for calculating the meter factor for volume flow The alternate method for calculating the meter factor for volume flow is used to avoid the difficulties that may be associated with the standard method. This alternate method is based on the fact that volume is inversely proportional to density.
Page 167: Perform A D1 And D2 Density Calibration Using Prolink Iii

Measurement support Use meter validation and meter factors, rather than calibration, to prove the meter against a regulatory standard or to correct measurement error. Prerequisites • During density calibration, the sensor must be completely filled with the calibration fluid, and flow through the sensor must be at the lowest rate allowed by your application.
Page 168: Perform A D1 And D2 Density Calibration Using The Field Communicator

Measurement support Postrequisites If you disabled LD Optimization before the calibration procedure, re-enable it. 9.8.2 Perform a D1 and D2 density calibration using the Field Communicator Read the Prerequistes on page 159 if you have not already done so. See the following figure. Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 169: Perform A D3 And D4 Density Calibration (T-Series Sensors Only)

Measurement support Postrequisites If you disabled LD Optimization before the calibration procedure, re-enable it. Perform a D3 and D4 density calibration (T- Series sensors only) For T-Series sensors, the optional D3 and D4 calibration could improve the accuracy of the density measurement if the density of your process fluid is less than 0.8 g/cm or greater than 1.2 g/cm…
Page 170: Perform A D3 Or D3 And D4 Density Calibration Using Prolink Iii

Measurement support • Perform both the D3 and D4 calibrations if you have two calibrated fluids (other than air and water). The calibrations must be performed without interruption, in the order shown. Make sure that you are prepared to complete the process without interruption.
Page 171: Perform A D3 Or D3 And D4 Density Calibration Using The Field Communicator

Measurement support Figure 9-7: D3 or D3 and D4 density calibration using ProLink III Close shutoff valve downstream from sensor D3 Calibration D4 Calibration Fill sensor with D3 fluid Fill sensor with D4 fluid Device Tools > Device Tools > Calibration >…
Page 172: Perform Temperature Calibration

Measurement support Figure 9-8: D3 or D3 and D4 density calibration using the Field Communicator D3 Calibration D4 Calibration Close shutoff valve Fill sensor with D3 fluid Fill sensor with D4 fluid downstream from sensor On-Line Menu > Service Tools > Service Tools >…
Page 173: Perform Temperature Calibration Using The Display

Measurement support Prerequisites The temperature calibration is a two-part procedure: temperature offset calibration and temperature slope calibration. The two parts must be performed without interruption, in the order shown. Ensure that you are prepared to complete the process without interruption. You will need a low-temperature calibration fluid and a high-temperature calibration fluid.
Page 174
Measurement support Temperature Offset Calibration Temperature Slope Calibration Fill sensor with Fill sensor with low-temperature fluid high-temperature fluid Wait until sensor achieves Wait until sensor achieves thermal equilibrium thermal equilibrium Device Tools > Device Tools > Calibration > Calibration > Temperature Calibration >…
Page 175: Perform Temperature Calibration Using The Field Communicator

Measurement support 9.10.3 Perform temperature calibration using the Field Communicator Temperature Offset calibration Temperature Slope calibration Fill sensor with low- Fill sensor with high- temperature fluid temperature fluid Wait until sensor achieves Wait until sensor achieves thermal equilibrium thermal equilibrium Service Tools >…
Page 176
Measurement support Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 177: Chapter 10 Troubleshooting

Troubleshooting Troubleshooting Topics covered in this chapter: • Status LED states • Status alerts, causes, and recommendations • Locate a device using the HART 7 Squawk feature • Flow measurement problems • Density measurement problems • Temperature measurement problems • Milliamp output problems •…
Page 178: Status Led States

Troubleshooting 10.1 Status LED states The status LED on the transmitter indicates whether or not alerts are active. If alerts are active, view the alert list to identify the alerts, then take appropriate action to correct the alert condition. Your transmitter has a status LED only if it has a display. If the transmitter has a display and LED Blinking is disabled, the status LED does not flash to indicate an unacknowledged alert.
Page 179
Troubleshooting Alert num- Alert title Possible cause Recommended actions A002 RAM Error (Core Pro- The core processor has experienced • Cycle power to the meter. cessor) a memory error. • Replace the core processor. • Contact customer support. A003 No Sensor Response The transmitter is not receiving one •…
Page 180
Troubleshooting Alert num- Alert title Possible cause Recommended actions A008 Density Overrange The line density is greater than • If other alerts are present, resolve those 10 g/cm (10000 kg/m alert conditions first. If the current alert persists, continue with the recommen- ded actions.
Page 181
Troubleshooting Alert num- Alert title Possible cause Recommended actions A011 Zero Calibration Many possible causes, such as too • Verify that there is no flow through the Failed: Low much flow, especially reverse flow, sensor, cycle power to the meter, then through the sensor during a calibra- retry the procedure.
Page 182
Troubleshooting Alert num- Alert title Possible cause Recommended actions A017 Sensor Case Tem- The values computed for the resist- • Check your process conditions against perature (RTD) Fail- ance of the meter and case RTDs the values reported by the device. Tem- are outside limits.
Page 183
Troubleshooting Alert num- Alert title Possible cause Recommended actions A020 Calibration Factors Some calibration factors have not • Verify all of the characterization or cali- Missing been entered or are incorrect. bration parameters. See the sensor tag or the calibration sheet for your meter. •…
Page 184
Troubleshooting Alert num- Alert title Possible cause Recommended actions A026 Sensor/Transmitter The transmitter has lost communi- • Check the wiring between the sensor Communications cation with the core processor. and the transmitter. Failure There may be a problem with the •…
Page 185
Troubleshooting Alert num- Alert title Possible cause Recommended actions A033 Insufficient Pickoff The signal from the sensor pick- • Check for air in the flow tubes, tubes Signal off(s) is insufficient. This suggests not filled, foreign material in the tubes, that the sensor tubes or vibrating coating in the tubes, or other process elements are not vibrating.
Page 186
Troubleshooting Alert num- Alert title Possible cause Recommended actions A102 Drive Overrange The drive power (current/voltage) is • Check the drive gain and the pickoff at its maximum. voltage. • Check the wiring between the sensor and the transmitter. • Verify that internal wiring is secure and that there are no internal electrical problems.
Page 187
Troubleshooting Alert num- Alert title Possible cause Recommended actions A108 Basic Event 1 On The process has triggered Basic • No action required. Event 1. • Review event configuration if you be- lieve the event was triggered errone- ously. A109 Basic Event 2 On The process has triggered Basic •…
Page 188
Troubleshooting Alert num- Alert title Possible cause Recommended actions A117 Density Overrange The measured density is outside the • Check your process conditions against (Petroleum) range of the API table. the values reported by the device. • Verify the configuration of the petrole- um measurement application and rela- ted parameters.
Page 189: Locate A Device Using The Hart 7 Squawk Feature

Troubleshooting 10.3 Locate a device using the HART 7 Squawk feature The Squawk feature causes the device to show a specific pattern on its display. You can use this to locate or identify a device. Restriction The Squawk feature is available only with HART 7 connections from the Field Communicator. It is not available with ProLink III.
Page 190
Troubleshooting Problem Possible causes Recommended actions Erratic non-zero flow • Leaking valve or seal • Verify that the sensor orientation is appro- rate at no-flow condi- • Two-phase flow priate for your application (refer to the tions • Plugged or coated sensor tube sensor installation manual).
Page 191: Density Measurement Problems

Troubleshooting Problem Possible causes Recommended actions Inaccurate flow rate • Wiring problem • Check the wiring between the sensor and or batch total • Inappropriate measurement unit the transmitter. • Incorrect flow calibration factor • Verify that the measurement units are con- •…
Page 192: Temperature Measurement Problems

Troubleshooting Problem Possible causes Recommended actions Unusually high densi- • Plugged or coated sensor tube • Ensure that all of the calibration parame- ty reading • Incorrect density calibration factors ters have been entered correctly. See the • Incorrect temperature measurement sensor tag or the calibration sheet for your •…
Page 193: Milliamp Output Problems

Troubleshooting Problem Possible causes Recommended actions Temperature reading • Sensor temperature not yet equalized • If the error is within the temperature speci- slightly different from • Sensor leaking heat fication for the sensor, there is no prob- process temperature lem.
Page 194
Troubleshooting Table 10-2: Milliamp output problems and recommended actions (continued) Problem Possible causes Recommended actions Loop test failed • Output not powered • Verify that the output loop is powered ex- • Power supply problem ternally. • Wiring problem • If applicable, check the output wiring to •…
Page 195: Frequency Output Problems

Troubleshooting Table 10-2: Milliamp output problems and recommended actions (continued) Problem Possible causes Recommended actions Consistently incorrect • Loop problem • Check the mA Output trim. mA measurement • Output not trimmed correctly • Verify that the measurement units are con- •…
Page 196: Using Sensor Simulation For Troubleshooting

Troubleshooting 10.9 Using sensor simulation for troubleshooting When sensor simulation is enabled, the transmitter reports user-specified values for basic process variables. This allows you to reproduce various process conditions or to test the system. You can use sensor simulation to help distinguish between legitimate process noise and externally caused variation.
Page 197: Check Sensor-To-Transmitter Wiring

Troubleshooting Ensure that the power supply wires are connected to the correct terminals. Ensure that the power supply wires are making good contact, and are not clamped to the wire insulation. Inspect the voltage label inside the wiring compartment. The voltage supplied to the transmitter should match the voltage specified on the label.
Page 198: Check Grounding

Troubleshooting Verify that the wires are making good contact with the terminals. Check the continuity of all wires from the transmitter to the sensor. 10.12 Check grounding A sensor and the transmitter must be grounded. If the core processor is installed as part of the transmitter or the sensor, it is grounded automatically.
Page 199
Troubleshooting b. Read the mA current at the receiving device and compare it to the transmitter output. The readings do not need to match exactly. If the values are slightly different, you can correct the discrepancy by trimming the output. c.
Page 200: Perform Loop Tests Using Prolink Iii

Troubleshooting Postrequisites • If the mA Output readings are within 20 microamps of the expected values, you can correct this discrepancy by trimming the output. • If the discrepancy between the mA Output readings is greater than 20 microamps, or if at any step the reading was faulty, verify the wiring between the transmitter and the remote device, and try again.
Page 201: Perform Loop Tests Using The Field Communicator

Troubleshooting c. Click Fix FO. d. Read the frequency signal at the receiving device and compare it to the transmitter output. e. Click UnFix FO. Test the Discrete Output(s). a. Choose Device Tools > Diagnostics > Testing > Discrete Output Test. b.
Page 202
Troubleshooting e. Read the mA current at the receiving device and compare it to the transmitter output. The readings do not need to match exactly. If the values are slightly different, you can correct the discrepancy by trimming the output. f.
Page 203: Trim Ma Output

Troubleshooting 10.14 Trim mA output Trimming an mA output calibrates the transmitter’s mA output to the receiving device. If the current trim value is inaccurate, the transmitter will under-compensate or over- compensate the output. 10.14.1 Trim mA output using ProLink III Trimming the mA output establishes a common measurement range between the transmitter and the device that receives the mA output.
Page 204: Check The Hart Communication Loop

Troubleshooting Check the trim results. If any trim result is less than −20 microamps or greater than +20 microamps, contact customer service. 10.15 Check the HART communication loop If you cannot establish or maintain HART communications, the HART loop may be wired incorrectly.
Page 205: Check Hart Burst Mode

Troubleshooting When HART Address is changed, some configuration tools will automatically change mA Output Action. Always verify mA Output Action after setting or changing HART Address. Procedure Set HART Address as appropriate for your HART network. The default address is 0. This is the recommended value unless the transmitter is in a multidrop network.
Page 206: Check For Radio Frequency Interference (Rfi)

Troubleshooting Restriction For some status alerts, Alert Severity is not configurable. If there are no active fault conditions, continue troubleshooting. 10.20 Check for radio frequency interference (RFI) The transmitter’s Frequency Output or Discrete Output can be affected by radio frequency interference (RFI).
Page 207: Check Flow Direction

Troubleshooting Restriction For some status alerts, Alert Severity is not configurable. If there are no active fault conditions, continue troubleshooting. 10.23 Check Flow Direction If Flow Direction is set inappropriately for your process, the transmitter may report flow data that is not appropriate for your requirements. The Flow Direction parameter interacts with actual flow direction to affect flow values, flow totals and inventories, and output behavior.
Page 208: Check The Drive Gain

Troubleshooting Check the process for cavitation, flashing, or leaks. Monitor the density of your process fluid output under normal process conditions. Check the settings of Two-Phase Flow Low Limit, Two-Phase Flow High Limit, and Two-Phase Flow Timeout. You can reduce the occurrence of two-phase flow alerts by setting Two-Phase Flow Low Limit to a lower value, Two-Phase Flow High Limit to a higher value, or Two-Phase Flow Timeout to a higher value.
Page 209: Collect Drive Gain Data

Troubleshooting Table 10-4: Possible causes and recommended actions for excessive (saturated) drive gain (continued) Possible cause Recommended actions Plugged sensor tube Check the pickoff voltages (see Section 10.27). If either of them are close to zero (but neither is zero), plugged tubes may be the source of your prob- lem.
Page 210: Collect Pickoff Voltage Data

Troubleshooting To know whether your pickoff voltage is unusually low, you must collect pickoff voltage data during the problem condition and compare it to pickoff voltage data from a period of normal operation. Drive gain and pickoff voltage are inversely proportional. As drive gain increases, pickoff voltages decrease and vice versa.
Page 211: Check For Internal Electrical Problems

Troubleshooting 10.28 Check for internal electrical problems Shorts between sensor terminals or between the sensor terminals and the sensor case can cause the sensor to stop working. Possible cause Recommended action Moisture inside the sensor junction Ensure that the junction box is dry and no corrosion is present.
Page 212
Troubleshooting Table 10-7: Coils and test terminal pairs (continued) Coil Sensor model Terminal colors Resistance temperature detector Yellow to violet (RTD) Lead length compensator (LLC) All except T-Series and CMF400 Yellow to orange (see note) Composite RTD All CMFSs, T-Series, H300, and Yellow to orange F300 Fixed resistor (see note)
Page 213: Check The Core Processor Led

Troubleshooting h. Test the yellow terminal against all other terminals except the orange and violet ones. i. Test the violet terminal against all other terminals except the yellow and orange ones. There should be infinite resistance for each pair. If there is any resistance at all, there is a short between terminals.
Page 214
Troubleshooting Figure 10-1: Integral installation components A. Transmitter B. Transition ring C. 4 x cap screws (4 mm) D. Base E. Core processor b. Rotate the transmitter counter-clockwise so that the cap screws are in the unlocked position. c. Gently lift the transmitter straight up, disengaging it from the cap screws. Important Do not disconnect or damage the wires that connect the transmitter to the core processor.
Page 215
Troubleshooting Figure 10-2: 9-wire remote installation components A. Transmitter B. Core processor C. 4 x cap screws (4 mm) D. End cap b. Inside the core processor housing, loosen the three screws that hold the core processor mounting plate in place. Do not remove the screws.
Page 216: Core Processor Led States

Troubleshooting Postrequisites To return to normal operation: • For a 4-wire remote installation or a remote core processor with remote transmitter installation, replace the core processor lid. • For an integral installation: 1. Without pinching or stretching the wires, lower the transmitter onto the base, inserting the cap screws into the slots.
Page 217
Troubleshooting Table 10-8: Standard core processor LED states (continued) LED state Description Recommended actions Core processor receiving less • Verify power supply wiring to core processor. than 5 volts • If transmitter status LED is lit, transmitter is re- ceiving power. Check voltage across terminals 1 (VDC+) and 2 (VDC–) in core processor.
Page 218: Perform A 700 Core Processor Resistance Test

Troubleshooting Table 10-9: Enhanced core processor LED states (continued) LED state Description Recommended action Core processor internal failure The meter requires factory service. 10.30 Perform a 700 core processor resistance test Note You can perform a resistance test only on a 700 core processor. Procedure Power down the transmitter.
Page 219
Troubleshooting c. Gently lift the transmitter straight up, disengaging it from the cap screws. If you have a 9-wire remote installation: a. Remove the end-cap. Figure 10-3: 9-wire remote installation components A. Transmitter B. Core processor C. 4 x cap screws (4 mm) D.
Page 220
Troubleshooting Measure the resistance between core processor terminal pairs 3–4, 2–3, and 2–4. Terminal pair Function Expected resistance 3–4 RS-485/A and RS-485/B 40 kΩ to 50 kΩ 2–3 VDC– and RS-485/A 20 kΩ to 25 kΩ 2–4 VDC– and RS-485/B 20 kΩ…
Page 221: Appendix A Using The Transmitter Display

Using the transmitter display Appendix A Using the transmitter display Topics covered in this appendix: • Components of the transmitter interface • Use the optical switches • Access and use the display menu system • Display codes for process variables •…
Page 222: Use The Optical Switches

Using the transmitter display Figure A-1: Transmitter interface Status LED Display (LCD panel) Process variable Scroll optical switch Optical switch indicator Select optical switch Unit of measure for process variable Current value of process variable Use the optical switches Use the optical switches on the transmitter interface to control the transmitter display. The transmitter has two optical switches: Scroll and Select.
Page 223: Access And Use The Display Menu System

Using the transmitter display Table A-1: Optical switch indicator and optical switch states Optical switch indicator State of optical switches Solid red One optical switch is activated. Flickering red Both optical switches are activated. Access and use the display menu system The display menu system is used to perform various configuration, administrative, and maintenance tasks.
Page 224: Enter A Floating-Point Value Using The Display

Using the transmitter display Use the Scroll and Select optical switches to navigate to your destination in the display menu system. • Use Scroll to move through a list of options. • Use Select to choose the current option. If Scroll flashes on the display, activate the Scroll optical switch, then the Select optical switch, and then the Scroll optical switch again.
Page 225
Using the transmitter display Procedure • To change the value: 1. Activate Select until the digit you want to change is active (flashing). Select moves the cursor one position to the left. From the leftmost position, Select moves the cursor to the rightmost digit. 2.
Page 226
Using the transmitter display If the displayed value is the same as the value in transmitter memory, you will be returned to the previous screen. If the displayed value is not the same as the value in transmitter memory, SAVE/ YES? flashes on the display.
Page 227: Display Codes For Process Variables

Using the transmitter display d. Activate Scroll until the desired character is displayed. e. Activate Select to move the cursor one digit to the left. f. Activate Scroll until the desired character is displayed. g. Activate Select to move the cursor one digit to the left. h.
Page 228: Codes And Abbreviations Used In Display Menus

Using the transmitter display Table A-2: Display codes for process variables (continued) Code Definition Comment or reference LZERO Live zero flow MASSI Mass inventory MTR_T Case temperature (T-Series sensors only) NET M Net mass flow rate Concentration measurement application only NET V Net volume flow rate Concentration measurement application only…
Page 229
Using the transmitter display Table A-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference AUTO SCRLL Auto Scroll BKLT Backlight B LIGHT Calibrate CH A Channel A CHANGE PASSW Change password Change the password or passcode required for or passcode access to display functions CHANGE CODE…
Page 230
Using the transmitter display Table A-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference EXTRN External FAC Z Factory zero Flow calibration factor FLDIR Flow direction FL SW Flow switch FLSWT Frequency Output FO FREQ Frequency factor FO RATE…
Page 231
Using the transmitter display Table A-3: Codes and abbreviations used in display menus (continued) Code or abbrevia- tion Definition Comment or reference QUAD Quadrature Revision SCALE Scaling method SFM60 Shrinkage factor PVR applications only corrected volume of mix at 60F SFO60 Shrinkage Fac Corr PVR applications only…
Page 232
Using the transmitter display Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 233: Appendix B Using Prolink Iii With The Transmitter

In most ProLink III installations, the manual is installed with the ProLink III program. Additionally, the ProLink III manual is available on the documentation CD or at www.emerson.com. ProLink III features and functions ProLink III offers complete transmitter configuration and operation functions. ProLink III also offers a number of additional features and functions, including: •…
Page 234: Connect With Prolink Iii

Using ProLink III with the transmitter • The ability to connect to and view information for more than one device • A guided connection wizard These features are documented in the ProLink III manual. They are not documented in the current manual.
Page 235: Connect With Prolink Iii To The Service Port

Using ProLink III with the transmitter • You cannot make concurrent Modbus connections if the connections use the same terminals. You can make concurrent Modbus connections if the connections use different terminals. B.2.2 Connect with ProLink III to the service port CAUTION! If the transmitter is in a hazardous area, do not use a service port connection.
Page 236: Make A Hart/Bell 202 Connection

Using ProLink III with the transmitter Figure B-1: Connection to service port A. PC B. Signal converter C. Service port terminal 7 (RS-485/A) D. Service port terminal 8 (RS-485/B) E. Transmitter, with wiring compartment and power supply compartment opened Note This figure shows a serial port connection.
Page 237
Using ProLink III with the transmitter CAUTION! If the transmitter is in a hazardous area, do not connect directly to the transmitter terminals. Connecting directly to the transmitter terminals requires opening the wiring compartment, and opening the wiring compartment while the transmitter is powered up could cause an explosion.
Page 238
Using ProLink III with the transmitter Figure B-2: Connection to transmitter terminals – A. Computer B. Signal converter Ω resistance C. 250–600 D. Transmitter, with wiring compartment and power supply compartment opened E. External power supply Note This figure shows a serial port connection. USB connections are also supported. The signal converter must be connected across a resistance of 250–600 Ω.
Page 239
Using ProLink III with the transmitter Figure B-3: Supply voltage and resistance requirements 1000 Operating range Supply voltage VDC (volts) Note To connect to a point in the local HART loop: a. Attach the leads from the signal converter to any point in the loop. b.
Page 240
Using ProLink III with the transmitter Figure B-4: Connection over local loop – A. PC B. Signal converter C. Any combination of resistors R1, R2, and R3 as necessary to meet HART communication resistance requirements D. DCS or PLC E. Transmitter, with wiring compartment and power supply compartment opened F.
Page 241
Using ProLink III with the transmitter Figure B-5: Supply voltage and resistance requirements 1000 Operating range Supply voltage VDC (volts) Note To connect over a HART multidrop network: a. Attach the leads from the signal converter to any point on the network. b.
Page 242
Using ProLink III with the transmitter Figure B-6: Connection over multidrop network A. Signal converter Ω resistance B. 250–600 C. Devices on the network D. Master device Start ProLink III. Choose Connect to Physical Device. Set Protocol to HART Bell 202. HART/Bell 202 connections use standard connection parameters.
Page 243
Using ProLink III with the transmitter Option Description Primary Use this setting if no other primary host is on the network. The Field Communicator is a secondary host. Click Connect. Need help? If an error message appears: • Verify the HART address of the transmitter, or poll HART addresses 1–15. •…
Page 244
Using ProLink III with the transmitter Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 245: Appendix C Using A Field Communicator With The Transmitter

If you are unable to perform these tasks, consult the Field Communicator manual before attempting to use the Field Communicator. The Field Communicator manual is available on the documentation CD or at www.emerson.com. Device descriptions (DDs) In order for the Field Communicator to work with your device, the appropriate device…
Page 246: Connect With The Field Communicator

Using a Field Communicator with the transmitter Field Communicator menus and messages Many of the menus in this manual start with the On-Line menu. Ensure that you are able to navigate to the On-Line menu. As you use the Field Communicator with a Micro Motion transmitter, you will see a number of messages and notes.
Page 247
Using a Field Communicator with the transmitter Figure C-1: Field Communicator connection to transmitter terminals A. Field Communicator Ω resistance B. 250–600 C. External power supply D. Transmitter, with wiring compartment and power supply compartment opened To connect to a point in the local HART loop, attach the leads from the Field Communicator to any point in the loop and add resistance as necessary.
Page 248
Using a Field Communicator with the transmitter Figure C-3: Field Communicator connection to multidrop network A. Field Communicator B. Devices on the network C. External power supply (may be provided by the PLC) Ω resistance (may be provided by the PLC) D.
Page 249: Appendix D Default Values And Ranges

Default values and ranges Appendix D Default values and ranges Default values and ranges The default values and ranges represent the typical factory transmitter configuration. Depending on how the transmitter was ordered, certain values may have been configured at the factory and are not represented in the default values and ranges. Table D-1: Transmitter default values and ranges Type…
Page 250
Default values and ranges Table D-1: Transmitter default values and ranges (continued) Type Parameter Default Range Comments Volume factor Density Density damping 1.6 sec 0.0 – 51.2 sec User-entered value is corrected to nearest valid value in a list of preset values.
Page 251
Default values and ranges Table D-1: Transmitter default values and ranges (continued) Type Parameter Default Range Comments Special units Base mass unit Base mass time Mass flow conversion factor Base volume unit Base volume time Volume flow conversion factor Variable map- Primary variable Mass flow ping…
Page 252
Default values and ranges Table D-1: Transmitter default values and ranges (continued) Type Parameter Default Range Comments 0.00 g/cm Read-only. LSL is calculated based on the sensor size and characterization parameters. 10.00 g/cm Read only. USL is calculated based on the sensor size and characterization parameters.
Page 253
Default values and ranges Table D-1: Transmitter default values and ranges (continued) Type Parameter Default Range Comments Frequency Output polarity Active high Last measured value timeout 0.0 seconds 0.0 – 60.0 sec Discrete Out- Source Flow direction Fault Indicator None Power Internal Polarity…
Page 254
Default values and ranges Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 255: Appendix E Transmitter Components And Installation Wiring

Transmitter components and installation wiring Appendix E Transmitter components and installation wiring Topics covered in this appendix: • Installation types • Power supply terminals and ground • Input/output (I/O) wiring terminals Installation types The transmitter was ordered and shipped to be installed in one of several possible configurations.
Page 256
Transmitter components and installation wiring Figure E-2: High-temperature meters with factory connection The transmitter is shipped with a flexible connection factory installed between the sensor and the transmitter. The transmitter must be dismounted from its shipping location (spot-welded to the sensor case) and then mounted separately.
Page 257
Transmitter components and installation wiring Figure E-4: Remote core processor with remote sensor installation The transmitter, core processor, and sensor are all mounted separately. The 4-wire connection between the transmitter and core processor must be field wired. The 9-wire connection between the core processor and the sensor must be field wired.
Page 258: Power Supply Terminals And Ground

Transmitter components and installation wiring Power supply terminals and ground Figure E-5: Power supply wiring terminals Warning flap Equipment ground Power supply wiring terminals (9 and 10) Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 259: Input/Output (I/O) Wiring Terminals

Transmitter components and installation wiring Input/output (I/O) wiring terminals Figure E-6: I/O wiring terminals mA/HART Frequency Output or Discrete Output mA Output Configuration and Use Manual…
Page 260
Transmitter components and installation wiring Micro Motion Model 2700 Transmitters with Intrinsically Safe Outputs…
Page 261: Appendix F Ne 53 History

NE 53 history Appendix F NE 53 history NE 53 history Important Not all features and capabilities described in this section may apply to your transmitter or configuration. August 2000, Version 1.x Modification type Change Expansion Added writing of the device tag using Modbus Adjustment Improved communication handling with the HART Tri-Loop prod- Feature…
Page 262
NE 53 history December 2001, version 3.x Modification type Change Expansion • Added support for the configurable I/O option board • Software version information available via the display or Modbus • Configurable density cutoff • Additional HART variables can be assigned to QV •…
Page 263
NE 53 history September 2006, version 5.x Modification type Change Expansion • Discrete Output assignable as a flow switch • Discrete Output fault indication configurability • Discrete Input support for multiple action assignments • Added support for querying the display LED status via Mod- •…
Page 264
NE 53 history Modification type Change Feature • Configurable hysteresis for flow switch • Field Verification Zero added to support Weights & Measures application • Transmitter firmware checksum and core processor firmware checksum assignable as display variables and viewable in Pro- Link February 2018, version 8.x Modification type…
Page 265
NE 53 history Modification type Change Adjustment • Sensors that are not straight tube sensors are now correctly identified • The mA Output fixed alert is now set • The Factory Configuration Invalid status bit is now set cor- rectly when connected to a 700 core processor — as the 700 core processor does not support saving and restoring the fac- tory configuration •…
Page 266
NE 53 history Modification type Change An AMS Field Device did not respond message no longer displays when the concentration offset is con- figured even though the value was changed When the volume flow type is changed, the new setting is updated from the transmitter without having to rescan the device Feature…
Page 267
NE 53 history Configuration and Use Manual…
Page 268
© 2018 Micro Motion, Inc. All rights reserved. The Emerson logo is a trademark and service mark of Emerson Electric Co. Micro Motion, ELITE, ProLink, MVD and MVD Direct Connect marks are marks of one of the Emerson Automation Solutions family of companies. All other marks are property of their respective owners.

Источник

VLADiz: новенький; Сообщения: 1; Зарегистрирован: 13 авг 2021, 15:39; Имя: владислав; Страна: россия; город/регион: волгоград

Micro Motion победить

Сообщение

VLADiz » 16 авг 2021, 16:47

Трансмиттеры моделей 1700 и 2700 обеспечивают:
1) компактный интегральный монтаж на расходомере с возможностью поворота на 360 градусов
2) интерфейс оператора по месту для зон Класса I, Раздела 1/Зоны 1, позволяющий:
— Просматривать технологические переменные
— Быстро определять функциональное состояние расходомера
— Просматривать и принимать аварийные сообщения
— Запускать, останавливать и сбрасывать сумматор трансмиттера
— Устанавливать расходомер на ноль
— Выполнять имитационные проверки выходов
— Изменять единицы измерения
— Назначать переменные по выходам
— Масштабировать выходы
— Устанавливать параметры обмена данными через RS-485
— функции интерфейса могут настраиваться и защищаться паролем
набор инструментов впечатляет .
вылетает ошибка А009 А0014 А026 А 003 больше всего ошибка 26 пугает сбой связи сенсора ( маленькое отступление ему поменяли сам преобразователь и у него версия по5 у трансмитера версия 2 . произвожу сброс ошибок при помощи хардика ошибки сбрасываються но проходит пять минут и он опять перестает работать .скажите может у кого было так

Источник

Micro motion 2700 ошибки

Related Manuals for Emerson Micro Motion 2700

Summary of Contents for Emerson Micro Motion 2700

Page 3: Table Of Contents

Page 9: Getting Started

Page 11: Before You Begin

Page 12: Additional Documentation And Resources

Page 13: Chapter 2 Quick Start

Page 14: Transmitter Status Reported By Led

Page 15: Determine The Foundation Fieldbus Unique Device Id

Page 17: Part Ii Configuration And Commissioning

Page 19: Introduction To Configuration And Commissioning

Page 21: Default Values And Ranges

Page 22: Place Function, Transducer, And Resource Blocks In Oos Mode

Page 23: Restore The Factory Configuration

Page 25: Configure Process Measurement

Page 28: Configure Flow Damping

Page 29: Configure Mass Flow Cutoff

Page 30: Configure Volume Flow Measurement For Liquid Applications

Page 33: Configure Volume Flow Cutoff

Page 34: Configure Gsv Flow Measurement

Page 35: Configure Standard Density Of Gas

Page 38: Configure Gas Standard Volume Flow Cutoff

Page 39: Configure Flow Direction

Page 41: Configure Density Measurement

Page 42: Configure Two-Phase Flow Parameters

Page 43: Configure Density Damping

Page 44: Configure Density Cutoff

Page 45: Configure Temperature Measurement

Page 46: Configure Temperature Damping

Page 47: Effect Of Temperature Damping On Process Measurement

Page 49: Configure Petroleum Measurement Using The Field Communicator

Page 51: Set Up Concentration Measurement

Page 52: Configure Concentration Measurement Using The Field Communicator

Page 54: Standard Matrices For The Concentration Measurement Application

Page 55: Derived Variables And Calculated Process Variables

Page 56: Set Up Concentration Measurement Using A Basic Ff Host

Page 57: Set Reference Temperature Values For Specific Gravity Using A Basic Ff Host

Page 58: Modify Extrapolation Alerts For Concentration Measurement Using A Basic Ff Host

Page 59: Select The Active Concentration Matrix Using A Basic Ff Host

Page 60: Configure Pressure Compensation Using Prolink Iii

Page 61: Options For Pressure Measurement Unit

Page 63: Configure Device Options And Preferences

Page 64: Configure The Process Variables And Diagnostic Variables Shown On The Display

Page 65: Configure The Number Of Decimal Places (Precision) Shown On The Display

Page 66: Configure The Refresh Rate Of Data Shown On The Display

Page 67: Enable Or Disable The Display Backlight

Page 68: Enable Or Disable Operator Actions From The Display

Page 69: Enable Or Disable Totalizer Reset From The Display

Page 70: Configure Security For The Display Menus

Page 72: Configure Response Time Parameters

Page 73: Configure Status Alert Severity

Page 75: Configure Informational Parameters

Page 76: Configure Sensor Serial Number

Page 77: Configure Sensor Liner Material

Page 78: Configure Descriptor

Page 79: Complete The Configuration

Page 80: Return Function Blocks To In Service (Auto) Mode

Page 81: Part Iii Operations, Maintenance, And Troubleshooting

Page 83: Chapter 7 Transmitter Operation

Page 84: View Process Variables

Page 85: View Process Variables And Other Data Using Prolink Iii

Page 86: View Transmitter Status Using The Status Led

Page 87: View And Acknowledge Status Alerts

Page 89: View And Acknowledge Alerts Using Prolink Iii

Page 90: View Alerts Using The Field Communicator

Page 91: Alert Data In Transmitter Memory

Page 92: Start And Stop Totalizers And Inventories

Page 93: Reset Totalizers

Page 94: Reset Totalizers Using The Display

Page 95: Reset Inventories

Page 97: Chapter 8 Measurement Support

Page 98: Smv Requirements

Page 99: Run Smv

Page 102: View Test Data

Page 105: Schedule Automatic Execution Of The Smv Test

Page 108: Zero The Meter

Page 109: Validate The Meter

Page 111: Alternate Method For Calculating The Meter Factor For Volume Flow

Page 112: Perform A D1 And D2 Density Calibration Using Prolink Iii