Machine not homed multicam ошибка

1. 03-24-2016, 10:25 PM

   
   

   #1

   

   
   Registered
   

   ---

   I have a Multicam MG 3000 and it has its days. I think my first wife had fewer issues than it. My usual problem is having to adjust the 5-volt voltage to 5.04 this will give ey power faults. Today I was cutting fine and was going along great till I tried cutting 1 3/4 » in one pass ( ok yes it was me not the Enroute software more on the in another form.) after hitting the master stop I needed to find home again when the machine found z &y it then slowed like usual at the end of x but instead of stopping completely it just kept inching it’s way to the stop till it started bending the stops over. Tried a few times and the same each time. Everything looks good I did have to set the 5-volt voltage again but …
   Thanks in advance,
   Joe
   BTW Great resource this cnczone.com

   ---

2. 03-25-2016, 03:00 AM

   
   

   #2

   

   
   Registered
   

   ---

   Re: Not finding home on Multicam MG 3000
   

   Joe,

   You have a couple of problems going on:

   1. If you are adjusting your power supply often, then most likely it is time to replace the power supply. The 5 volt is something that you adjust to 5.09 and if you do a yearly PM, that is something we normally check and adjust if needed.

   2. Your machine not finding X, seems little sudden to not be able to find X but check:
   a. Find you limits on the XA/XB sides, open your control cabinet and look for the control board, take a screw driver and check to see when you touch the front of the sensor that it does the light go off on the sensor. If so on the control board there are some LED lights, look for the ones labeled XA/XB home, as you touch the limit sensor with the screwdriver does corresponding LED go off on the control board.

   Depending on the age of your machine, if could be sensor, cable or if the sensor has move position and need to be adjusted.

   If you are still having problems give me a call
   678-548-1483
   Maurice
   MCP Services

   ---

3. 03-25-2016, 01:40 PM

   
   

   #3

   

   
   Registered
   

   ---

   Re: Not finding home on Multicam MG 3000
   

   Maurice, Looks you were right on, I needed to do a little adjusting and we are up and running this morning. I also bumped up the power supply we will see how that works.
   Thanks for all your help,
   Joe

   ---

4. 03-27-2016, 02:39 PM

   
   

   #4

   

   
   Registered
   

   ---

   Re: Not finding home on Multicam MG 3000
   

   Glad i was able to help you out Joe. This maybe a time for you to schedule a PM of your machine, have someone come in a check it out, if you have ran for multiple years, small problems start to happen that can be madding. We check out the electrical/mechanical give recommendation on what we see weather is happens to be machine related i.e. tooling, feeds speeds, application related questions.

   I know that having a technician to come in and check your machine out is not a guarantee that you aren’t going to run into issue with your machine. How many of you can be down, with your tight production timelines or the added expense of a electrical component shorting out another component.

   1. Stop using duct tape, it is not for permanent repair. I have seen duct tape cause 10K in electrical damage
   2. If your spindle is making a louder then normal sounds, don’t ignore. A basic bearing repair about 2500-3000, can easily be 10K plus if ignored.
   3. Fliters for your vacuum pump are not forever, and those that have PD pumps with roots blowers they require a oil change every year.

   These are things I see constantly, that users (operators) and owners disregard.

   Take the time to have technician come in if not every year at least once every 2 years.

   Sorry Joe, just me on my soapbox. My apologies for going off on a tangent.
   

   OH…..and if a technician comes in for a repair, tell us everything. If someone ran into it with a forklift, you recently moved the machine ( on a new power circuit), a part was replaced by someone else or a classic you or your IT dept has done a replacement or upgrade and now it won’t communicate.

   Small pieces of information, help us greatly.

   ---

Вернуться в «Граверы и фрезеры MULTICAM»

На производстве стоит 2 станка мультикам5000, те кто их покупал и настраивал — давно уволены и недоступны. На каждый станок стоит свой комп. На одном компе глюкнул винт — винда не загружается. Для работы компа со станком ТОЧНО нужен установленный job server. Дистрибутива нет. Реестр сдох. Все компы и станки висят в общей локальной сети, но каждый станок видит только свой комп (папку с рабочими файлами).

Вопрос: как станок определяет, где его комп, и как перенести/настроить jobserver с исправного компа? Или может кто знает, где взять дистрибутив и как оно настраивается с нуля. Ещё есть забэкапленая (ранее, пока комп был исправен) папка «Productivity Software Suite» с этим jobserver-ом, но я не вижу там никаких настроек на конкретный станок. Куда они привязываются? К айпишнику, к серийнику? Единственное что нашёл — в реестре есть айпишник станка. Но вряд ли при установке руками реестр правят, а из джобсервера настройку айпишника не нашёл.

Вопрос не такой срочный: мы используем кривоглючную программу type edit3 4.2, хотелось бы перейти на более современные, но нужен постпроцессор под мультикам, может есть у кого готовые, и не жалко?

Mechanical Installation: PHASE II

Electricity is required.

 Slightly loosen gantry bolts – Loosen both sides of the X-axis (moving gantry only).

 Hard Home – If machine will not find limits, then see Help Docs.

 Verify Resolutions – See Help Docs for more information on how to check resolution

 Verify Table Parameters – Jog the full distance in X-, Y-, & Z-axes. Make sure that the gantry & head

do not make physical contact with the end stops.

 Verify the cutting head is parallel to the table.

 Square Table – Use a pen taped to the side of the head to make 4 points to verify the square of the

gantry. The bigger the perfect rectangle or square, the more accurate.

 Tighten Gantry Bolts – Tighten both sides of the X-axis (moving gantry only).

Suite4 Machine Software Installation

 Reboot Machine – Check for red letter errors.

 Capture NVRAM – Check the factory Flash settings before making any modifications. Save to

Computer and Tech computers.

 Check Init and Firmware Version – Type v & press Enter. Capture the screen or write down the

information. Make updates if necessary.

Interface Board

Controller Board Revision

Firmware Version (MCIF)

 Help Files – Manuals & Help Docs

 JobReporter – Confirm operations.

 ConnectionManager – Confirm operations.

Innovation. Quality. Performance. Best in Industry. Worldwide.

Voltage Chart

Incoming at Switch

(L1,L2,L3)

Transformed Power

(Pins 23&24)

____________

Init File Version Loader

____________

Init File Version STD

____________

MD4 Version

 JobNameServer – Confirm operations.

 JobEditor – Confirm operations.

 JobConsole – Check if Auto Preview

____________

____________

works & if Job Monitor is on.

Routers * Lasers * Plasma * WaterJets * Knife Cutters

www.MultiCam.com

____________

____________

____________

I just got a used MG 4000 series MultiCam CNC machine, and I can’t get it to run any files that I make in Fusion 360. After spending lots of time on the phone with MultiCam and searching through many threads here I haven’t been able to figure out how to fix the issue. All help is appreciated. 

Currently I am trying to cut out a simple rectangular shelf with some slots in it. Here are the steps I look to make it:

1. I created two operations doing a set of 2d slots, then a 2d contour. I ran the simulation, and it cuts just how I’d like.

2. I did the post process using the MultiCam ISO and left the «retract Z level» at «1» (I don’t understand what this does honestly so I didn’t mess with it).

3. On the machine side I set a «home», «surface height», and «maximum depth» using the controller.

4. Finally I went to the CNC file on my MultiCam controller and hit run program. 

This is where I get an error code on the machine control pad. It says:

Out Of Bounds

Axis = Z

Position = -0.6000

Attached is a picture of the model with tool paths, a copy of the .cnc file, and a picture of the control pad with error. Not sure why but it wouldn’t let me post a .cnc file so I just changed it to a .nc file. No other aspects of the file were changed.

Thank you again for your help.