Коды сброса ошибок sharp коды сброса ошибок sharp

В большинстве случаев расходные материалы для оборудования SHARP имеют двойной запас прочности. И если нет общих замечаний по качеству отпечатка (или копии) можно попытаться немного сэкономить на сервисе. Так же стоит отметить, что принтеры и МФУ SHARP имеют интуитивно понятную механическую часть, что позволяет минимально подготовленному инженеру в целом разобраться с установкой деталей.

необходимые коды для сброса некоторых сообщений о неисправностях:

Для того, что бы произвести один из сбросов следует войти в сервисный режим. Вход в сервисный режим отличается по моделям устройств (коды для входа в сервисный режим в таблице №2)
После входа в Сервисный режим с кнопочной клавиатуры устройства набираем:
{ основной код } – кнопка Start – { дополнительный код } – кнопка Start

Таблица № 1

Коды входа в сервисный режим оргтехники SHARP:

Таблица № 2

Sharp 1420, 1430

A1 Jam in document feeder

A2 Jam in document feeder

C1 Cassette misfeed

C2 Cassette feed, bypass unplugged

C3 Bypass misfeed

E1 Paper feed jam

E3 Exit jam

EE-EL Developer overtoned during setup

EE-EU Developer undertoned during setup

J0 Developer setup taking place

J1 Add toner

J3 Drum unit not installed properly or missing

J7 Drum unit due for replacing

J8 Wrong drum unit or power was turned on after J7 displayed

L6 Key counter or other optional counter accessory problem

U1 Drive problem

U2 Scan

U3 Lens

U4-01 Fuser thermistor

U4-02 High fuser temperature

U4-03 Low fuser temperature

U5 500 sheet cassette lift motor

U6 Main board problem

U7 Document glass too hot (with document feeder)

U8 Problem with line voltage

U9 Auto developer setup problem

Sharp 2014

A1 Jam in document feeder

A2 Jam in document feeder

C1 Cassette misfeed

C2 Cassette feed, bypass unplugged

C3 Bypass misfeed

E1 Paper feed jam

E3 Exit jam

EE-EL Developer overtoned during setup

EE-EU Developer undertoned during setup

H2-0 Fusing unit temperature error

H3-0 Overheated fusing unit

H4-0 The fusing unit doesn’t heat up

J0 Developer setup taking place

J1 Add toner

J3 Drum unit not installed properly or missing

J7 Drum unit due for replacing

J8 Wrong drum unit or power was turned on after J7 displayed

L1-0 Scanner position error

L3-0 Scanner position error

L4-1 Main motor drive overloaded

L5-2 Lens position error

L6 Key counter or other optional counter accessory problem

L8-1 Zero cross signal error

L8-3 Auto-exposure sensor malfunction

U1 Drive problem

U2 Scan

U3 Lens

U4-01 Fuser thermistor

U4-02 High fuser temperature

U4-03 Low fuser temperature

U5 500 sheet cassette lift motor

U6 Main board problem

U7 Document glass too hot (with document feeder)

U8 Problem with line voltage

U9 Auto developer setup problem

Sharp 2020

CC Original detection problem

CH Lit Steadily: Sorter not installed, or not turned on

CH Flashing: DV unit not installed, not connected properly, or not latched in place properly

F1 Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport motor drive.

F2 Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark sensor problem. . Does not see mark on drum or sensor not working properly.

H2 Sub code 00: Fuser thermistor open.

H3 Sub code 00: Fuser temperature too high.

H4 Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections.

L1 Scan forward problem. Motor, sensor, board

L3 Scan forward problem. Motor, sensor, board.

L4 Drive problem; main motor, gear, sensor, bind.

L5 Lens problem. Motor sensor board.

L8 Sub code 01: Zero cross.

P Paper feed problem or no paper

PC Card counter not installed

U2 Sub code 01: Memory loss.

U4 Sub code 00: Communication problem between copier and duplex unit.

U5 Sub code 00: Communication problem between main board and ADF.

Sharp 2022, 2027, 2035

P10 Set or clear departmental counter

P11 Display individual departmental counts

P13 Clear departmental counters

P14 Enter, clear or change department numbers

P16 Change max. number of copies that can be run

P18 Sends alarm if the wrong department number is tried three times in a row

P19 Change code number

P20 Adjust auto exposure

P21 Adjust automautic shufoff

P22 Adjust manual exposure

P23 Adjust auto clear time

P24 Set up fixed magnification settings

P25 Set maximum number of copies or of sets

P26 Binding margin

P27 Border erase setting

P28 Defaults at power on

P29 Display various counts

P30 Auto repeat on or off

P45 Message display time

P70 Auto paper select on or off

P71 Auto cassette select on or off

P72 Maximum copies in duplex

P73 Copy condition in rewrite

P74 Duplex limit when problems with duplex unit

P75 Prevent auto duplex

P76 Prevent stapling

P77 Prevent cover use

P90 List programs

Sharp 2025, 2030, 2040

C2 Transfer corona problem or HVT

CC Original detection problem.

CH Door open or developer unit not installed, not connected properly, or not latched in place properly.

F1 Sub code 00: Communication error between main board and sorter. 01: Jogger error. 02: Sorter transport motor drive. 04: Sorter bin sensor problem. Lower limit sensed wrong.

F2 Sub code 02: Toner motor problem. 31: Image density sensor problem. Could be a problem with the light level. 32: Drum mark sensor problem. Does not see mark on drum or sensor does not work properly. 35: Grid voltage correction will not work during simulation.

F3 Sub code 12: Copier upper cassette lift motor problem. Copier bottom cassette lift motor problem.

H2 Fuser thermistor open.

H3 Fuser temperature too high.

H4 Fuser temperature too low. Lamp, thermal switch, connections.

L4 Sub code 01: Drive problem, main motor, sensor, bind.

L5 Sub code 03: Drive problem with 4th/5th mirror assembly, motor, sensor, board.

L8 Sub code 01: Power frequency problem.

PC Card counter or key counter not installed.

PF There is an inhibit command from the PC modem. This is reset with simulation 17.

U2 Sub code 00 or 01: Memory error.

U3 Sub code 20: Mirror motor locked. 21: Mirror motor home sensor.

U4 Sub code 02: Duplex alignment plate out of position motor, cable, sensor.

U5 Sub code 00: Communication problem between main board and RADF. 01: RADF motor drive problem. 02: RADF motor drive problem. 03: RADF resist sensor. 04: RADF exit sensor.

U6 Sub code 00: Communication error between copier and desk. 01, 02, 03: Desk lift motor drive problem. 08: Desk 24v problem. 09: LCT motor overload. 10: Desk transport motor drive problem.

U7 Sub code 00: Communication problem between copier and PC modem.

Sharp 2050

CC-nn Original sensing problem

CH Lit steadily: Door open

CH Flashing: Developer unit not installed, not latched or not installed properly

EE-EL During developer calibration, overtoned condition detected

EE-EU During developer calibration, undertoned condition detected

F1-00 Communication problem between main board and stapler

F1-02 Stapler sorter transport drive problem

F1-03 Problem with guide bar oscillator motor

F1-04 Index lower sensor

F1-05 Index upper sensor

F1-06 Shift motor problem in stapler sorter, or index motor problem

F1-08 Staple sorter shift motor drive problem

F1-10 Stapler problem

F2-00 Toner sensor problem

F2-31 Drum surface reflecting problem

F2-32 Drum sensor not scanning mark properly

F2-33 Grid voltage is too high or too low

F2-35 During patch detection, measurement is wrong

F2-37 Drum mark sensor adjustment problem

F3-01 LCT encoder

F3-02 LCT lift problem

F3-03 LCT down problem

F3-12 Cassette 1 lift problem

F3-22 Cassette 2 lift problem

F3-32 Cassette 3 lift problem

F3-42 Cassette 4 lift problem

H2-00 Fuser thermistor

H3-00 Fuser temperature too high

H4-00 Fuser temperature too low

L1-00 Scan problem

L2-00 Mirror motor drive problem

L3-00 Scan return problem

L4-01 Drum motor drive problem

L4-02 Main motor drive problem

L5-00 4/5 mirror drive problem

L8-01 Full wave signal missing to auto exposure

L8-02 Full wave signal to auto exposure is incorrect

L8-03 During auto exposure adjust procedure, the auto exp.

P20 Adjust automatic exposure

P21 Auto shut off timing

P22 Toner save mode

P25 Maximum number of copies that can be selected

P26 Margin shift

P28 Initial status

P29 To read total copies

P70 Auto paper select

P72 Bypass in duplex

P74 Stop document feeder use

P75 Stop duplex use

P76 Stop stapler use

P83 Modem access to codes through phone line

P90 Display all of the operator programs

PC Card counter

PF Modem problem

U0-00 Operation panel problem

U2-00 EEPROM error. Reset with sim. 16

U3-00 Communication problem between master and mirror controller

U3-20 Mirror drive problem

U3-21 Mirror home sensor problem

U3-26 Mirror motor voltage problem

U3-41 Lens motor home correction did not go well

U3-42 4/5 mirror motor problem similar to U3 -41

U4-02 Duplex alignment plate sensor

U4-03 Duplex rear plate sensor

U5-00 Communication problem between RADF and copier

U5-01 RADF resist sensor

U5-02 RADF reverse sensor

U5-03 RADF timing sensor

U5-04 RADF empty sensor

U5-11 RADF paper feed drive problem

U5-12 RADF transport drive problem

U7-00 Communication problem between copier and modem

Sharp 2114

A1 Jam in document feeder

A2 Jam in document feeder

C1 Cassette misfeed

C2 Cassette feed, bypass unplugged

C3 Bypass misfeed

E1 Paper feed jam

E3 Exit jam

EE-EL Developer overtoned during setup

EE-EU Developer undertoned during setup

J0 Developer setup taking place

J1 Add toner

J3 Drum unit not installed properly or missing

J7 Drum unit due for replacing

J8 Wrong drum unit or power was turned on after J7 displayed

L6 Key counter or other optional counter accessory problem

U1 Drive problem

U2 Scan

U3 Lens

U4-01 Fuser thermistor

U4-02 High fuser temperature

U4-03 Low fuser temperature

U5 500 sheet cassette lift motor

U6 Main board problem

U7 Document glass too hot (with document feeder)

U8 Problem with line voltage

U9 Auto developer setup problem

Sharp 2116, 2118

CH Sorter not installed or not turned on

CH blinking DV unit not installed, not connected properly

EE-EL During developer calibration, problem of some kind. Over toned

EE-EU During developer calibration, problem of some kind. Under toned

F1-00 Communication error between main board and sorter

F1-02 Transport motor drive

F1-04 Bin sensor problem. Upper or lower limit sensor problem

F1-05 Sorter bin home sensor

F1-06 Sorter bin motor drive

F1-14 Take out sensor problem

F2-31 Image density sensor problem

F2-32 Drum mark sensor problem

F2-35 Grid voltage correction will not work on the patch voltage is outside the expected range

H2-00 Fuser thermistor open

H3-00 Fuser temperature too high

H4-00 Fuser temperature too low. Lamp, thermal switch, connections

L1 Scan forward problem

L3 Scan return problem

L4 Drive problem; main motor, gear, sensor, bind

L5 Lens problem

L8-01 Zero cross (board problem)

L8-03 Auto exposure sensor problem

P Paper feed problem

PC Card counter not installed

U2-01 Memory loss

U2-04 EEPROM error

U5-00 Communication problem between main board and ADF

U5-01 Registration sensor problem during adjustment, or adjustment value is not a valid number

U5-02 Exit sensor adjustment problem; invalid adjustment value

U5-11 Paper feed drive problem

U5-12 Transport motor drive

Sharp 2120, 2216

CC Original detection problem

CH Sorter not installed, or not turned on

CH blinking DV unit not installed, not connected properly, or not latched in place properly

F1 Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport motor drive.

F2 Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark sensor problem. Does not see mark on drum or sensor not working properly.

H2 Sub code 00: Fuser thermistor open.

H3 Sub code 00: Fuser temperature too high.

H4 Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections.

L1 Scan forward problem. Motor, sensor, board

L3 Scan forward problem. Motor, sensor, board.

L4 Drive problem; main motor, gear, sensor, bind.

L5 Lens problem. Motor sensor board.

L8 Sub code 01: Zero cross.

P Paper feed problem or no paper

PC Card counter not installed

U2 Sub code 01: Memory loss.

U4 Sub code 00: Communication problem between copier and duplex unit.

U5 Sub code 00: Communication problem between main board and ADF.

Sharp 2214

A1 Jam in document feeder

A2 Jam in document feeder

C1 Cassette misfeed

C2 Cassette feed, bypass unplugged

C3 Bypass misfeed

E1 Paper feed jam

E3 Exit jam

EE-EL Developer overtoned during setup

EE-EU Developer undertoned during setup

J0 Developer setup taking place

J1 Add toner

J3 Drum unit not installed properly or missing

J7 Drum unit due for replacing

J8 Wrong drum unit or power was turned on after J7 displayed

L6 Key counter or other optional counter accessory problem

U1 Drive problem

U2 Scan

U3 Lens

U4-01 Fuser thermistor

U4-02 High fuser temperature

U4-03 Low fuser temperature

U5 500 sheet cassette lift motor

U6 Main board problem

U7 Document glass too hot (with document feeder)

U8 Problem with line voltage

U9 Auto developer setup problem

Sharp 2216

CC Original not detected in DF

CH Sorter problems

CH blinking Dev unit is not properly installed

L1 Scanner position error

L3 Scanner position error

L4 Main motor drive overloaded

L5 Lens position error

L8-01 Main board malfunction

L8-03 Auto-exposure sensor malfunction

H2-00 Fusing unit temperature error

H3-00 Overheated fusing unit

H4-00 The fusing unit doesn’t heat up

U2-01 Memory back-up battery dead

U2-04 EPROM error

U5-00 Communication with the ADF is lost

U5-02 Exit sensor error in ADF

U5-11 Paper feed drive overloaded in ADF

U5-16 Cooling fan overloaded in ADF

F1-00 Lost communication with the Sorter

F1-02 Main drive overloaded in Sorter

F1-04 Bin position error in sorter

F1-05 Bin position error in sorter

F1-06 Paper exit drive overloaded in sorter

F1-14 Paper presence sensor error in sorter

F1-16 Paper transport motor overloaded in sorter

F2-31 ID pattern reading error

F2-32 ID pattern reading error

F2-33 Grid voltage error

F2-35 Grid voltage error

F2-37 ID pattern reading error

EE-EU Low toner density in the developer

EE-EL High toner density in the developer

P Add paper

PC Key counter not installed

Sharp 2314

CH If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing, developer seal still installed, or toner density sensor/main board problem.

EE Sub code EU: undertoned. May be toner density sensor problem or developer unit problem.Sub code EL: Over toned. May be toner density sensor problem or developer unit problem.

H2 Sub code 0: Fuser thermistor.

H3 Sub code 0: Fuser temperature too high.

H4 Sub code 0: Fuser temperature too low.

L1 Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.

L3 Scan return problem. Sub code 0. Approximately same causes as L1

L4 Sub code 1: Main drive problem. Sensor, gear, motor.

L5 Sub code 2: Lens drive, motor, sensor.

L8 Sub code 1: Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE sensor problem.

PC Key counter not installed.

SPFJAM Document feeder problem.

U2 Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem.

U5 Sub code 5: high temperature at exposure glass when using document feeder.

Sharp 2414, 2514

CH If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing, developer seal still installed, or toner density sensor/main board problem.

EE Sub code EU: undertoned. May be toner density sensor problem or developer unit problem. Sub code EL: Over toned. May be toner density sensor problem or developer unit problem.

H2 Sub code 0: Fuser thermistor.

H3 Sub code 0: Fuser temperature too high.

H4 Sub code 0: Fuser temperature too low.

L1 Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.

L3 Scan return problem. Sub code 0. Approximately same causes as L1

L4 Sub code 1: Main drive problem. Sensor, gear, motor.

L5 Sub code 2: Lens drive, motor, sensor.

L8 Sub code 1 Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE sensor problem.

PC Key counter not installed.

SPFJAM Document feeder problem.

U2 Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem.

U5 Sub code 5: high temperature at exposure glass when using document feeder

Sharp 7100, 7200

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH possible DV unit not installed properly

CH Interlock or thermal fuse

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 7320, 7370

CH Door open or developer unit out

EL Developer problem

EU Developer set up problem

P flashing Out of paper

P lit No cassette in machine

PC Personal counter not installed

U3 Auto exposure sensor problem

Sharp 750

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH Interlock or thermal fuse

CH possible DV unit not installed properly

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 755, 756, 760

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH possible DV unit not installed properly

CH Interlock or thermal fuse

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 770

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH possible DV unit not installed properly

CH Interlock or thermal fuse

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

0 Main board, operations panel

0 Data transfer (main and operations)

0 Data transfer (main and ADF)

1 Document feeded motors

1 Exposure lamp board or operations

2 Automatic exposure sensor, exposure lamp board

U Press {Print} and read secondary code:

U3 Press {Print} and read secondary code:

U4 Press {Print} and read secondary code:

Sharp 7700, 7750

0 Data transfer (main and ADF)

0 Data transfer (main and operations)

0 Main board, operations panel

1 Document feeded motors

1 Exposure lamp board or operations

2 Automatic exposure sensor, exposure lamp board

U Press {Print} and read secondary code:

U3 Press {Print} and read secondary code:

U4 Press {Print} and read secondary code:

Sharp 771

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH possible DV unit not installed properly

CH Interlock or thermal fuse

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 780

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH Interlock or thermal fuse

CH possible DV unit not installed properly

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

CC Document sensor

CH Door open

EE Developer did not set up properly

EL Developer sensor

EU Developer sensor

H2 Thermistor

H3 High temperature

H4 Low temperature

L1 Forward scan

L2 Forward scan

L3 Scan return

L5 Lens

L6 Bottom rotating cassette

L8 Signal

L9 Sorter

U1 Battery

U2 Back up battery

U3 Auto exposure sensor

U5 Problem in interface between machine and ADF

Sharp 7800

CC Document sensor

CH Door open

EE Developer did not set up properly

EL Developer sensor

EU Developer sensor

H2 Thermistor

H3 High temperature

H4 Low temperature

L1 Forward scan

L2 Forward scan

L3 Scan return

L5 Lens

L6 Bottom rotating cassette

L8 Signal

L9 Sorter

U1 Battery

U2 Back up battery

U3 Auto exposure sensor

U5 Problem in interface between machine and ADF

Sharp 781

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH possible DV unit not installed properly

CH Interlock or thermal fuse

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

L6 Charge block switch

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 7850

CC Document sensor

CH Door open

EE Developer did not set up properly

EL Developer sensor

EU Developer sensor

H2 Thermistor

H3 High temperature

H4 Low temperature

L1 Forward scan

L2 Forward scan

L3 Scan return

L5 Lens

L6 Bottom rotating cassette

L8 Signal

L9 Sorter

U1 Battery

U2 Back up battery

U3 Auto exposure sensor

U5 Problem in interface between machine and ADF

Sharp 7900

CC Not sensing document on glass

CH Door open/DV unit not installed properly

EE DV did not set up properly

EL DV problem-overtoned condition

EU DV problem-undertoned condition

H2 Fuser thermistor

H3 Fuser temperature too high

H4 Fuser temperature too low

L1 Forward scan

L3 Return scan

L7 Developer unit shift problem

PC Key counter

U1 Dead battery

U2 Battery problem

Sharp 810

1 Open interlock switch

2 Bad thermofuse/thermistor

3 High or low temperature

4 Scanner problem

0 Data transfer

10 Mirror base

4 Stepping motor clock pulse

40 Lens

8 Mirror motor

U3 Press {Print} and read secondary code:

Sharp 8100

0 Data transfer

10 Mirror base

4 Stepping motor clock pulse

40 Lens

8 Mirror motor

U3 Press {Print} and read secondary code:

Sharp 811

1 Door or separator interlock

2 Instantly=Thermofuse

3 High temperature

4 Low temperature (if it takes 11 min)

5 Scanner problem if it takes several seconds

6 Optics problem on 820

7 Thermistor

Sharp 815

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH possible DV unit not installed properly

CH Interlock or thermal fuse

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

L6 Charge block switch

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 816

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH Interlock or thermal fuse

CH possible DV unit not installed properly

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

L6 Charge block switch

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 820

1 Door or separator interlock

2 Instantly=Thermofuse

3 High temperature

4 Low temperature (if it takes 11 min)

5 Scanner problem if it takes several seconds

6 Optics problem on 820

7 Thermistor

A1 Document feeder problem.

CH Toner cartridge not installed or not installed properly.

H2 Sub code 0: Fuser thermistor.

H3 Sub code 0: Fuser temperature too high.

H4 Sub code 0: Fuser temperature too low.

L1 Document feeder problem.

L3 Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.

L4 Sub code 1: Main drive problem. Sensor gear motor.

L5 Sub code 2: Lens drive, motor, sensor

P Paper feed.

U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.

U5 Sub code 5: high temperature at exposing glass when using document feeder.

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH Interlock or thermal fuse

CH possible DV unit not installed properly

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

L6 Charge block switch

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 8200

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH Interlock or thermal fuse

CH possible DV unit not installed properly

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

L6 Charge block switch

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 825

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

A1 Document feeder problem.

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH possible DV unit not installed properly

CH Interlock or thermal fuse

CH Toner cartridge not installed or not installed properly.

H1 Heater thermal fuse

H2 Sub code 0: Fuser thermistor.

H2 Thermistor

H3 High Temperature

H3 Sub code 0: Fuser temperature too high.

H4 Sub code 0: Fuser temperature too low.

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Document feeder problem.

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L3 Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.

L4 PT/main motor

L4 Sub code 1: Main drive problem. Sensor gear motor.

L5 Lens

L5 Sub code 2: Lens drive, motor, sensor

L6 Charge block switch

P Paper feed.

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.

U3 Dark box

U5 Sub code 5: high temperature at exposing glass when using document feeder.

Sharp 826

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH Interlock or thermal fuse

CH possible DV unit not installed properly

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

L6 Charge block switch

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 8260

0 Data transfer

10 Mirror base

4 Stepping motor clock pulse

40 Lens

8 Mirror motor

U3 Press {Print} and read secondary code:

Sharp 830, 835

A1 Document feeder problem.

CH Toner cartridge not installed or not installed properly.

H2 Sub code 0: Fuser thermistor.

H3 Sub code 0: Fuser temperature too high.

H4 Sub code 0: Fuser temperature too low.

L1 Document feeder problem.

L3 Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.

L4 Sub code 1: Main drive problem. Sensor gear motor.

L5 Sub code 2: Lens drive, motor, sensor

P Paper feed.

U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.

U5 Sub code 5: high temperature at exposing glass when using document feeder.

CC Not sensing document on glass

CH Door open/DV unit not installed properly

EE DV did not set up properly

EL DV problem-overtoned condition

EU DV problem-undertoned condition

H2 Fuser thermistor

H3 Fuser temperature too high

H4 Fuser temperature too low

L1 Forward scan

L3 Return scan

L7 Developer unit shift problem

PC Key counter

U1 Dead battery

U2 Battery problem

Sharp 8300, 8350, 8400

CC Not sensing document on glass

CH Door open/DV unit not installed properly

EE DV did not set up properly

EL DV problem-overtoned condition

EU DV problem-undertoned condition

H2 Fuser thermistor

H3 Fuser temperature too high

H4 Fuser temperature too low

L1 Forward scan

L3 Return scan

L7 Developer unit shift problem

PC Key counter

U1 Dead battery

U2 Battery problem

Sharp 845

A1 Document feeder problem.

CH Toner cartridge not installed or not installed properly.

H2 Sub code 0: Fuser thermistor.

H3 Sub code 0: Fuser temperature too high.

H4 Sub code 0: Fuser temperature too low.

L1 Document feeder problem.

L3 Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.

L4 Sub code 1: Main drive problem. Sensor gear motor.

L5 Sub code 2: Lens drive, motor, sensor

P Paper feed.

U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.

U5 Sub code 5: high temperature at exposing glass when using document feeder.

Sharp 850

1 Door or separator interlock

2 Instantly=Thermofuse

3 High temperature

4 Low temperature (if it takes 11 min)

5 Scanner problem if it takes several seconds

6 Optics problem on 820

7 Thermistor

Sharp 8600

0 Data transfer

10 Mirror base

4 Stepping motor clock pulse

40 Lens

8 Mirror motor

U3 Press {Print} and read secondary code:

Sharp 8875

C2 Transfer corona problem

CH If lit steadily, open door or other interlock. If flashing, developer unit not installed or not connected properly

H2 Fuser thermistor

H3 Fuser overheat. Triac pinched wire

H4 Low fuser temperature. Lamp, thermal fuse, thermistor, connection

L1 Scan problem. Did not leave home position

L2 Scan left home, but did not complete scan

L3 No return scan

L4 Drive problem

L5 Lens problem

L9 Sorter index. If 0 is flashing, sorter index home sensor did not actuate. If 1 is flashing, sorter bottom actuator remained actuated

U1 Battery. Replace battery (might have 2) and do simulation 13 to reset

U2 Communication problem within boards. To reset, jumper test points W2 & U2

Sharp 900, 901

0 Stepping motor

10 Mirror motor

40 Dark box switch

8 Mirror motor

C1 Charge corona

C2 Transfer corona

C3 Discharge corona

CH possible DV unit not installed properly

CH Interlock or thermal fuse

H1 Heater thermal fuse

H2 Thermistor

H3 High Temperature

H4 Low Temperature

H5 Lower thermofuse

H6 Lower thermistor

H7 High temperature in lower roller

H8 Low temperature in lower roller

L1 Forward Scan

L2 End of Scan

L3 Return of Scan

L4 PT/main motor

L5 Lens

L6 Charge block switch

P1 Copy lamp thermal fuse

U1 Low battery

U2 Data transfer

U3 Dark box

Sharp 9300, 9500, 9550

0 Desk board and main board

0 Data transfer

10 Desk alignment board

10 Mirror base

20 Sort gate

4 Stepping motor clock pulse

40 Lens

8 Mirror motor

U3 Press {Print} and read secondary code:

U4 Press {Print} and read secondary code:

[b]Sharp 9700, 9750

40 Flashing — Lens home problem

C2 Transfer corona

CH Lit — Door open

CH Flashing — DV unit not installed

CL Drum cleaner connector

H2 Thermistor

H3 High fuser temperature

H4 Low fuser temperature

L1 Mirror

L2 Scan

L3 Scan return

L4 Drive

L5 Lens

PC Key counter

U1 Dead battery

U2 Dead battery

U3 Lens or mirror

U4 Duplex

Sharp Z50, 55, 70

(Z70)E Magnification dial not set properly

H Heater problem (fuser has resettable

L Scan problem

P Paper feed problem

Sharp Z60

F Thermal fuse — exposure or fuser

H Heater problem

L Scan problem

U Low Battery

Sharp Z800

[b:5

Вернуться в Принтеры, МФУ, копиры формата A3

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 12