|
29 / 2 / 1 Регистрация: 22.12.2017 Сообщений: 5 |
|
|
1 |
|
|
10.12.2019, 12:13. Показов 11455. Ответов 4
Всем Привет, подскажите пожалуйста кто нибудь сталкивался с проблемой на принтере canon image runner advance c3320i Принтер был приобретён в 2016 отработал 3 года. За 3 года поменял: Миниатюры
__________________
0 |
|
Programming Эксперт 94731 / 64177 / 26122 Регистрация: 12.04.2006 Сообщений: 116,782 |
10.12.2019, 12:13 |
|
Ответы с готовыми решениями: Прошивка Canon C3320i
Подключили к сети — МФУ Canon c3320i. Установили драйвера на ПК, в настройках… Canon imageRUNNER Canon imagerunner 2520i 4 |
Настройка МФУ Canon c3320i|
Модератор
6871 / 3816 / 477 Регистрация: 13.03.2013 Сообщений: 14,056 Записей в блоге: 9 |
|
|
10.12.2019, 13:44 |
2 |
|
Рустам Хакимов, пробег аппарата?
0 |
|
2459 / 923 / 177 Регистрация: 03.03.2015 Сообщений: 6,477 |
|
|
10.12.2019, 20:24 |
3 |
|
подскажите пожалуйста кто нибудь сталкивался с проблемой на принтере canon image runner advance c3320i После перезагрузки выдаёт системную ошибку: E602-0801 Да.
0 |
|
29 / 2 / 1 Регистрация: 22.12.2017 Сообщений: 5 |
|
|
12.12.2019, 07:11 [ТС] |
4 |
|
Решение Добрый день всем, по проблеме принтера была решена следующим путём: Миниатюры
1 |
|
1 / 1 / 0 Регистрация: 20.06.2022 Сообщений: 1 |
|
|
13.07.2022, 15:11 |
5 |
|
на C3320 (без буквы i) с такой же ошибкой вход в инженерное меню получился так: на экране с ошибкой нажатие головы, потом одновременно 2+8 и снова голову. Выдается текстовое меню, где пункт 2 — проверка HDD. После выбора его и выключения с последующим включением начинается проверка на графическом уже фоне. После того как проверка прошла 1 раз, принтер снова выпал в ошибку, выключение и включение снова запустило проверку, которая уже прошла нормально и принтер загрузился.
1 |
E602-0801-00
Detection Description
Remedy
E602-0811-00
Detection Description
Remedy
HDD error
An error was detected in the general application-related area. (Initialization failed at startup or I/O
error at startup)
When this error occurs, the system has not been started normally. Therefore, it may not be
recorded in the error log.
[Related parts]
— Harness between the Main Controller PCB (UN05) and the HDD
— HDD
— Main Controller PCB (UN05)
[Remedy] Perform the following in the order while checking whether the error is cleared. When
prioritizing clearing of the error, skip Remedies 2 and 3.
Although the error is cleared by «HD-CHECK», it may occur again. Thus, perform Remedies 1 to
4.
1. Check the related harness/cable and connector.
2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> «8», and execute «HD-CHECK». Then,
turn OFF and then ON the main power.
3. Obtain the necessary backup data by referring to the backup data list.
[Reference] For backup and restoration, refer to «Adjustment> Main Controller System» and
«Appendix> Backup Data List» in the Service Manual.
4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> «8», and execute «HD-CLEAR». Then,
turn OFF and then ON the main power.
[Reference] Only the data in the corresponding partitions is deleted.
5. Enter safe mode using (2+8) startup. Then format the HDD and reinstall the system software
using SST or a USB flash drive.
6. Check/replace the related parts.
[Reference] Before replacing the Main Controller PCB, back up the service mode data (approx. 2
min) and restore the backup data after the replacement so the data may be able to be protected.
— Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP
— Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
HDD error
An error was detected in the general application-related area. (File could not be written in the HDD
after startup or I/O error after startup)
[Related parts]
— Harness between the Main Controller PCB (UN05) and the HDD
— HDD
— Main Controller PCB (UN05)
[Remedy] Perform the following in the order while checking whether the error is cleared. When
prioritizing clearing of the error, skip Remedies 2 and 3.
Although the error is cleared by «HD-CHECK», it may occur again. Thus, perform Remedies 1 to
4.
1. Check the related harness/cable and connector.
2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> «8», and execute «HD-CHECK». Then,
turn OFF and then ON the main power.
3. Obtain the necessary backup data by referring to the backup data list.
[Reference] For backup and restoration, refer to «Adjustment> Main Controller System» and
«Appendix> Backup Data List» in the Service Manual.
4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> «8», and execute «HD-CLEAR». Then,
turn OFF and then ON the main power.
[Reference] Only the data in the corresponding partitions is deleted.
5. Enter safe mode using (2+8) startup. Then format the HDD and reinstall the system software
using SST or a USB flash drive.
6. Check/replace the related parts.
[Reference] Before replacing the Main Controller PCB, back up the service mode data (approx. 2
min) and restore the backup data after the replacement so the data may be able to be protected.
— Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP
— Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
422
7. Error/Jam/Alarm
-
03-13-2021
#1
Junior Member
- Rep Power
- 0
[error e602-0801] C3325i format disk USB
Hello I cant seem to find a thread so I’ll try another.
I have this error code and I’m very new to this process. I’m trying to update the firmware with the USB. I’ve got the firmware for my machine and made the USB with SST. When I boot in safe mode i cant seem to get the format scrip to come up as the service manual suggests. Am I missing something?
I cannot format using 1+ 9
when I boot in safe mode,«
[[[[Wait for USB/SSTConnect menu<V8.04>]]]]] (v08.04)
[9] :version information
[RESET] : STart Shutdown Sequence
Checking USB.
Waiting SST infpormation
Starting USB task.«
Service manual says
«5. Terminate the SST.
6. Connect the USB memory device to the host machine, and start the host machine with download mode in safe mode.
7. Press keys on the Control Panel in the order shown below.� Press any keys� [4] : Clear/Format� [1] : Disk Format� [0] : OK� Press any keys� [C] : Return to Menu� [Reset] : Start shutdown sequence� [0] : OK (The power of the host machine is turned OFF automatically.)
«Im not getting anything when I hole any key.
I saw a youtube video that helped me reg the USB key, resolution of the video was poor but the info was helpful. It mentioned something about a verifying the format disk tool be on the USB. Do i need to add this manually?
All help or links for more info would be greatly appreciated.
Thank you.