C0f32 ошибка bizhub 211

Если вы не нашли на этой странице ваш код ошибки, то нажмите на кнопку «Запросить код ошибки», которая находится под этим текстом, заполните данные, после этого мы отправим информацию на указанную вами электронную почту, а также возможно, что мы добавим вашу ошибку в наш список.

Инфа сотка

• 

  Bizhub hack
  

  Серия подсказок «bizhub hack» сделает ваше общение с техникой Konica Minolta …

• 

  5партнер на связи
  

  Компания Пятый партнер не ушла с Российского рынка и продолжает работать. …

• 

  5partner награды в 2022
  

  Очередной год подряд самый большой объем продаж оборудования Konica Minolta …

• 

  C4065 vs C7090
  

  В этой статье мы наглядно покажем чем отличается профессиональная модель …

• 

• 

• 

  C257i офис в цвете
  

  Konica Minolta в 2021 году выпустила очередной хит цветной офисной бюджетной …

• 

• 

• 

• 

  C3070L vs C6085
  

  В этой статье мы наглядно покажем чем отличается профессиональная модель …

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• 

• MINOLTA EP1054 «Замятие» и C0F30

  Emperor RmPS в форуме Принтеры, МФУ, копиры формата A3

  4

  5934

  
  Emperor RmPS
  
  Ср дек 21, 2011 12:42 pm
  

• Konica 7013: Ошибка «H-VltFuse Diskonnect»

  aav в форуме Принтеры, МФУ, факсы, копиры формата A4

  1

  2475

  
  kvg
  
  Пт окт 28, 2011 11:23 pm
  

• canon bizhub c3110 ошибка «нет тонера»

  gruz18 в форуме Принтеры, МФУ, факсы, копиры формата A4

  12

  1874

  
  gruz18
  
  Пт дек 24, 2021 2:55 pm
  

• прошу помощи с программой Minolta-Epson Chip Reset

  kalina_vet в форуме Инструментарий

  14

  8338

  
  kalina_vet
  
  Ср фев 19, 2014 5:49 pm
  

• Minolta PagePro 1480MF — сканирует и копирует черный лист

  maksimthuk в форуме Xerox 3100 и иже с ним…

  5

  7089

  
  maksimthuk
  
  Чт дек 07, 2017 5:22 pm
  

Field Service Ver. 1.0 Apr. 2005

15.3.14

15.3.15

C0F33: Improperly Adjusted ATDC Sensor

A. Detection Timing

Trouble Code

• The measurement taken by the ATDC Sensor (UN1) at a time 2.0 sec. after the

C0F32

• The measurement taken by the ATDC Sensor (UN1) at a time 2.0 sec. after the

• The adjustment of the ATDC control voltage is not completed within 1 sec. after

C0F33

• The ATDC Sensor control voltage falls outside the range of 5.39 V to 8.15 V

B. Action

ATDC Sensor (UN1)

Step

Operations

1

Check to see if developer is available.

Check the ATDC Sensor connectors

2

for proper connection and correct as

necessary.

3

Change UN1.

4

Run «ATDC Auto Adjust.»

5

Change PWB-A.

6

Change PU1.

Main Motor (M1) has started turning is less than 5% (greater than 4.63 V).

Main Motor (M1) has started turning is 19% or more (1.41 V or less).

sampling has started of the ATDC Sensor (UN1) as part of an operation of

ATDC Sensor Automatic Adjustment.

during an operation of ATDC Sensor Automatic Adjustment.

Relevant Electrical Components

Ref.

Page

☞

Description

Master Board (PWB-A)

Power Supply Unit (PU1)

WIRING DIAGRAM

Control signal

–

–

–

–

–

–

103

–

–

–

–

–

15. Malfunction code

Location

(Electrical

Components)

–

–

–

–

–

–

145

Thanks:  0

Likes:  0

Dislikes:  0

1. 09-19-2013

   
   

   #1

   Dear Copy technet members,
   i am new(a student) here and i would like to request a solution for my problem( honestly it’s my fault).
   Our copier is Konica Minolta Bizhub210. the machine generates a black line as wide as 0.5 cm of line on the right margin of every paper we print. And because of that we can’t print any official papers, we could use it only for non-important papers to print. then i thought it was the problem of the drum and i tried to remove the drum. i tried to see if the drum has any defects and tried to shake it if there are things loosened. but i found nothing and when i put it back to test again the machine says (C0F32) call the technician. i did not know what to do. when i do a research about this error they say it is the problem of the ATDC sensor, as they suggest i tried to set the high gain of it. but no difference!
   And sadly, i am scolded almost everyday because of that. They complain me of playing with machine..i am really sad.
   actually i did not remember what i really did i remove the power cord from electrical out let? i am not sure. because i was in a hurry to print a little booklet. all i did was i un-screwed the drum unit from the machine and see, then i put it back…that’s all.
   1. is it because of i did not unplug the machine?
   2. what could be the problem and
   3. what could be the solution?
   Please help me in fraternal spirit. thank you and God bless all.

   ---

2. 09-20-2013

   
   

   #2

   Re: C0f32 error
   

   Take the drum unit out again. Hold it level and shake it gently. This will level out the developer inside the drum unit. Then re-install the drum unit. Turn the power off and then back on.

   ---

3. 09-20-2013

   
   

   #3

   Re: C0f32 error
   

   Lets start from black band. Suppose it is on the back side where are the gears. Drum might be ok but developer, rolls (distance) and some seals must me replaced. Is there an indication maintenance M1 or M2 on display…? Anyway You will need technician to do this work. You are just this «lucky» one that touched the machine right before it is dead.

   BR

   ---

4. 09-20-2013

   
   

   #4

   Re: C0f32 error
   

   Important data you left out…How many copies are on the meter? The code is caused by an imbalance of toner to developer. Developer has to be changed every so often, as does the drum. If your meter is way over the life, it was time to change anyway and you just aggravated it by messing with the drum. Until you post the meter, everyone is just guessing at your problem. Every field tech looks at the meter when they are working in the field, I always wonder how they can troubleshoot online without that info. The drum being at end of life can also be the cause of the black line.

   If you do not have access to a tech, you should at least buy a manual to understand how a copier works.

   The greatest enemy of knowledge isn’t ignorance, it is the illusion of knowledge. Stephen Hawking

   ---

5. 09-20-2013

   
   

   #5

   Re: C0f32 error
   

   This Parts & Service manual can now be purchased for $12.77 and downloaded immediately after payment from:

   Just Manuals, The Internet’s largest selection of manuals ~ Instant Downloads

   Paul@justmanuals.com

   ---

6. 09-21-2013

   
   

   #6

   Re: C0f32 error
   

   Originally Posted by ko lay
   

   Dear Copy technet members,
   i am new(a student) here and i would like to request a solution for my problem( honestly it’s my fault).
   Our copier is Konica Minolta Bizhub210. the machine generates a black line as wide as 0.5 cm of line on the right margin of every paper we print. And because of that we can’t print any official papers, we could use it only for non-important papers to print. then i thought it was the problem of the drum and i tried to remove the drum. i tried to see if the drum has any defects and tried to shake it if there are things loosened. but i found nothing and when i put it back to test again the machine says (C0F32) call the technician. i did not know what to do. when i do a research about this error they say it is the problem of the ATDC sensor, as they suggest i tried to set the high gain of it. but no difference!
   And sadly, i am scolded almost everyday because of that. They complain me of playing with machine..i am really sad.
   actually i did not remember what i really did i remove the power cord from electrical out let? i am not sure. because i was in a hurry to print a little booklet. all i did was i un-screwed the drum unit from the machine and see, then i put it back…that’s all.
   1. is it because of i did not unplug the machine?
   2. what could be the problem and
   3. what could be the solution?
   Please help me in fraternal spirit. thank you and God bless all.

   thanks for your kind answers…i am grateful to all of you. however..someone came and messed up the machine again, i think, now the machine showing not error C0f32 but c0f500. i do not want to touch it again. but if there is another solution i would like to receive it. in the meter…i see 143488… thanks

   ---

7. 09-21-2013

   
   

   #7

   Re: C0f32 error
   

   Did You mean C0500 — it is fuser error. Get service technician…

   BR

   ---

8. 09-21-2013

   
   

   #8

   Re: C0f32 error
   

   Originally Posted by fixthecopier
   

   Important data you left out…How many copies are on the meter? The code is caused by an imbalance of toner to developer. Developer has to be changed every so often, as does the drum. If your meter is way over the life, it was time to change anyway and you just aggravated it by messing with the drum. Until you post the meter, everyone is just guessing at your problem. Every field tech looks at the meter when they are working in the field, I always wonder how they can troubleshoot online without that info. The drum being at end of life can also be the cause of the black line.

   If you do not have access to a tech, you should at least buy a manual to understand how a copier works.

   yes, thank you i saw some number :143488…

   ---

9. 09-21-2013

   
   

   #9

   Re: C0f32 error
   

   Originally Posted by ivovb
   

   Did You mean C0500 — it is fuser error. Get service technician…

   BR

   yes. it is. my hands are off. thanks. God bless you.

   ---

10. 09-21-2013

    
    

    #10

    Change dv110.c0f32 is a low concentration in dv unit.old dv

    ---

Tags for this Thread