123 333 xerox ошибка

• Xerox Phaser 6600 «Invalid Yellow» / «Неверный желтый»

  kotya-potya в форуме Принтеры, МФУ, факсы, копиры формата A4

  5

  5299

  
  3100
  
  Пн ноя 18, 2019 8:24 pm
  

• Xerox WC 3119: «Замятие 1»

  kokubenko в форуме Принтеры, МФУ, факсы, копиры формата A4

  22

  38578

  
  kokubenko
  
  Ср ноя 23, 2011 4:47 pm
  

• Xerox WC3220 — Ложное замятие бумаги, Замятие 0

  Romeo в форуме Принтеры, МФУ, факсы, копиры формата A4

  25

  10107

  
  Romeo
  
  Пн окт 12, 2020 7:13 pm
  

• Xerox WC 3119 без признаков «жизни»

  MorZ в форуме Принтеры, МФУ, факсы, копиры формата A4

  5

  6696

  
  Goldwater
  
  Чт окт 08, 2020 11:34 pm
  

• Xerox 3428 «Установите Картридж»

  Roller-ch в форуме Принтеры, МФУ, факсы, копиры формата A4

  6

  9316

  
  SeMi
  
  Сб авг 27, 2011 6:42 pm
  

BSD-ON:

BSD 2.1 — User Interface (UI)

BSD-ON:

BSD 3.4 — ESS — UI Communication

The system detected that transmission with the Control Panel could not be established.

The H/W connection in the UI is faulty and the internal connection isn’t detected.

Initial Actions

Power Off/On

Procedure

•

Ensure that the customer is programming a job within the parameters of the machine uti-

lizing the UI.

•

Disconnect then reconnect the IIT, UI I/F, ESS, MCU all PWBs connected to them (RAM,

Firmware module, EEPROM)

•

Check the sw version of the controller sw — update if required

•

Replace UI I/F PWB

(PL

1.7)

•

Replace ESS PWB

(PL

35.2) (If not fixed by this, reinstall the original ESS PWB.)

Initial Issue

WorkCentre 5335 Family Service Documentation

123-337 Frame Data RAP

BSD-ON:

BSD 2.1 — User Interface (UI)

BSD-ON:

BSD 3.4 — ESS — UI Communication

The UI software failed and an incorrect data type value is detected.

Initial Actions

Power Off/On

Procedure

•

Ensure that the customer is programming a job within the parameters of the machine uti-

lizing the UI.

•

Disconnect then reconnect the IIT, UI I/F, ESS, MCU all PWBs connected to them (RAM,

Firmware module, EEPROM)

•

Check the sw version of the controller sw — update if required

•

Replace UI I/F PWB

•

Replace ESS PWB

07/2011

2-933

BUS Updated 12/2011

(PL

1.7)

(PL

35.2) (If not fixed by this, reinstall the original ESS PWB.)

Status Indicator RAPs

123-333 , 123-337

Thanks:  0

Likes:  0

Dislikes:  0

1. 11-02-2016

   
   

   #1

   

   
   Trusted Tech
   

   50+ Posts

   

   

   ---

   Rep Power

   17

   Xerox 412 — 123-333 I/F Fail (Impossible Communication)
   

   I’m new to the Xerox world, need to help a field tech with a Xerox 4112 and the manual indicates «install the Monza PWB» as one of the solutions for the 123-333 code. I don’t know what a «Monza Board» is and it’s not explained in the SM can someone explain this to me?

   Thanks in advance!

   ---

2. 11-02-2016

   
   

   #2

   Re: Xerox 412 — 123-333 I/F Fail (Impossible Communication)
   

   This code indicates a communication problem between the main unit (IOT) and your control panel / screen (UI). The cable that connects these two might be loose on either the UI side or the IOT side.

   Maybe this is your situation?
   Problem: At power up all 3 blue LEDs and power saver button flash on and off and machine eventually comes to 123-333 fault code. Unable to enter diagnostics or special boot mode.
   Cause: UI interface cable loose on one side.
   Solution: tighten knurled screws on UI interface cable, before checking MCU ribbon cables, etc.

   The board that this cable connects to on the IOT might be damaged too. I once had a customer that was getting new carpets installed. The carpet installers moved the machine by pulling it by the UI interface cable and damaged the connector on the board.

   ---